Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061818 DOOR LOCK _0304543 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 69760C 1.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.

w/o Double Locking System:

i.
B402286

Engage the guide to install the front door inside locking cable assembly to the front door lock with motor assembly.



b.

w/ Double Locking System:

i.
B450670

Engage the guide to install the front door inside locking cable assembly to the front door lock with motor assembly.


ii.
B450675C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws as shown in the illustration.



Hide 69720B 2.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.

w/o Double Locking System:

i.
B402285

Engage the guide to install the front door lock remote control cable assembly to the front door lock with motor assembly.



b.

w/ Double Locking System:

i.
B450668

Engage the guide to install the front door lock remote control cable assembly to the front door lock with motor assembly.



Hide 69035A 3.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY (w/o Double Locking System)

a.
B402284

Engage the guides to install the front door lock cover sub-assembly to the front door lock with motor assembly.


b.
B402287C02
0,0 0,0 false
V113147

Install in this Direction


Engage the claws as shown in the illustration.


Hide 69040A 4.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing a removed front door lock with motor assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock with motor assembly.



a.

Apply MP grease to the sliding parts of the front door lock with motor assembly.


b.

When reusing the front door lock with motor assembly (w/o Double Locking System):

i.

Install a new door lock wiring harness seal to the front door lock with motor assembly.



c.

When reusing the front door lock with motor assembly (w/ Double Locking System):

i.

Install a new door lock wiring harness seal to the front door lock with motor assembly.



d.
B450676C01
3.01,1.51 2.698,1.042 true 2.458,0.948 2.688,1.135 0.229,0.188 10 true *1
*1 Front Door Lock Open Rod
V113147

Install in this Direction


Connect the front door lock open rod as shown in the illustration.

HINT:

Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.



e.

Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


f.

Connect the connector.


Hide 69217D 5.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

Hide 67404F 6.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Hide 68151C 7.INSTALL FRONT DOOR GLASS RUN

Hide 67664 8.INSTALL DOOR FRAME UPPER GARNISH

Hide 68102 9.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Hide 67832 10.INSTALL FRONT DOOR SERVICE HOLE COVER

Hide 68195 11.INSTALL FRONT DOOR BELT SEAL

Hide 68172A 12.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

Hide 67602 13.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74231 14.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

Hide 74232 15.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

Hide 69284C 16.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

Hide 17.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 18.INITIALIZE POWER WINDOW CONTROL SYSTEM