Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
75976G
1.INSTALL NO. 2 FRONT DOOR STRIPE
75986G
2.INSTALL FRONT DOOR OUTSIDE STRIPE
75966B
3.INSTALL NO. 4 FRONT DOOR STRIPE
75754A
4.INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING
75752C
5.INSTALL FRONT DOOR FRONT WINDOW FRAME MOULDING
62112
6.INSTALL COWL SIDE TRIM BOARD
67914
7.INSTALL FRONT DOOR SCUFF PLATE
75720
8.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY
9.INSTALL HOLE CAP
Install the hole cap.
75788A
10.INSTALL FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY
75732A
11.INSTALL FRONT DOOR OUTSIDE MOULDING
67001A
12.INSTALL FRONT DOOR PANEL CUSHION
Engage the claws to install the 2 front door panel cushions.
68216
13.INSTALL FRONT DOOR FIX WINDOW WEATHERSTRIP
Install the front door fix window weatherstrip to the front door fix window glass.
68126
14.INSTALL FRONT DOOR FIX WINDOW GLASS
|
Install in this Direction |
Install the front door fix window glass with front door fix window weatherstrip as shown in the illustration.
86160
15.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY (w/ Speaker)
86262E
16.INSTALL FRONT SPEAKER COVER (w/o Speaker)
Engage the guide and claw to temporarily install the front speaker cover.
Using an air riveter or a hand riveter, install the front speaker cover with 3 new rivets in the order shown in the illustration.
| *a | Riveter |
| *b | Mandrel |
| *c | Incorrect |
Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.
| *a | Riveter |
| *b | Incorrect |
Confirm that the rivets are seated properly against the moulding.
Do not tilt the riveter when installing the rivet to the moulding.
Do not leave any space between the rivet head and moulding.
| *a | Riveter |
| *b | Incorrect |
Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.
Connect the connector.
67837B
17.INSTALL FRONT DOOR DUST PROOF SEAL
Install the 3 front door dust proof seals.
67862
18.INSTALL FRONT DOOR WEATHERSTRIP
| *a | Clip (A) |
Engage the clip (A) and other clip to install the front door weatherstrip.
68610
19.INSTALL FRONT DOOR CHECK ASSEMBLY
Apply MP grease to the sliding parts of the front door check assembly.
Clean the bolt hole in the vehicle body.
Clean the threads of the bolt (A).
Apply adhesive to the threads of the bolt (A).
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
| *a | Bolt (A) |
| *b | Bolt (B) |
Install the front door check assembly with the bolt (A) and 2 bolts (B).
69312
20.INSTALL FRONT DOOR LOCK OPEN ROD
| *a | Snap |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the snap to install the front door lock open rod to the front door outside frame sub-assembly as shown in the illustration.
69202A
21.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
w/ Protector:
Install the door outside handle protector with the 3 screws.
Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.
w/ Entry and Start System:
| *a | Guide |
| *b | Clamp |
Engage the clamps and guide.
| *a | Grommet |
| *b | Guide |
|
Install in this Direction |
Engage the grommet and guides to install the front door outside handle frame sub-assembly as shown in the illustration.
Using a T30 "TORX" socket wrench, tighten the screw.
w/o Entry and Start System:
| *a | Grommet |
| *b | Guide |
|
Install in this Direction |
Engage the grommet and guides to install the front door outside handle frame sub-assembly as shown in the illustration.
Using a T30 "TORX" socket wrench, tighten the screw.
69040A
22.INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY
69242E
23.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD
|
Install in this Direction |
Engage the guides to install the front door rear outside handle pad as shown in the illustration.
69241H
24.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD
|
Install in this Direction |
Engage the guide and claws to install the front door front outside handle pad as shown in the illustration.
69220
25.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY
|
Install in this Direction |
Install the front door outside handle assembly as shown in the illustration.
w/ Entry and Start System:
Connect the connector.
Engage the claws.
69217D
26.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
| *1 | Hole Plug |
|
Remove in this Direction |
Engage the claws to install the front door outside handle cover as shown in the illustration.
Using a T30 "TORX" socket wrench, tighten the screw.
Install the hole plug.
69217D
27.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)
|
Install in this Direction |
Engage the guides and claw to install the front door outside handle cover as shown in the illustration.
Apply MP grease to the sliding area of the front door lock cylinder assembly.
| *1 | Hole Plug |
|
Install in this Direction |
Install the front door outside handle cover with lock cylinder assembly as shown in the illustration.
Check that the front door lock cylinder assembly is inserted into the front door lock with motor assembly.
Using a T30 "TORX" socket wrench, tighten the screw.
Install the hole plug.
67404F
28.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
|
Install in this Direction |
Engage the guide to install the front door rear lower frame sub-assembly.
Install the bolt.
67402F
29.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Temporarily install the front door front lower frame sub-assembly with the 2 bolts.
Raise up the front door weatherstrip.
Install the screw.
Install the front door weatherstrip.
Tighten the 2 bolts.
68151C
30.INSTALL FRONT DOOR GLASS RUN
Install the front door glass run.
67664
31.INSTALL DOOR FRAME UPPER GARNISH
Engage the guides to install the door frame upper garnish.
32.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY
Apply MP grease to the sliding parts of the front door window regulator assembly.
| *a | Temporary Bolt |
Temporarily install the temporary bolt to the front door window regulator assembly.
Temporarily install the front door window regulator assembly with the 5 bolts.
Tighten the temporary bolt and 3 bolts to install the front door window regulator assembly.
Tighten the bolts in the order shown in the illustration.
Tighten the 2 bolts.
Connect the connector.
67831C
33.INSTALL NO. 2 FRONT DOOR SERVICE HOLE COVER
Engage the claws to install the No. 2 front door service hole cover.
68102
34.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
for Driver Side:
Connect the power window regulator master switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the front door glass sub-assembly so that the door glass bolt holes can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the power window regulator master switch assembly.
for Front Passenger Side:
Connect the power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the front door glass sub-assembly so that the door glass bolt holes can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the power window regulator switch assembly.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.
Be careful not to damage the front door glass sub-assembly.
Install the front door glass sub-assembly with the 2 bolts.
Install the hole plug.
89835
35.INSTALL DOOR SIDE AIRBAG SENSOR
67832
36.INSTALL FRONT DOOR SERVICE HOLE COVER
Engage the clips to install a new front door service hole cover.
Insert 3 new front door weatherstrip clips and turn them 45° as shown in the illustration.
87912A
37.INSTALL OUTER MIRROR PROTECTOR
|
Install in this Direction |
Engage the claws to install the outer mirror protector as shown in the illustration.
Install the 2 screws.
87940
38.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY
67838A
39.INSTALL FRONT DOOR VENT SEAL
Install the front door vent seal.
68195
40.INSTALL FRONT DOOR BELT SEAL
|
Install in this Direction |
Install the front door belt seal to the front door glass inner weatherstrip as shown in the illustration.
68172A
41.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP
|
Install in this Direction |
Install the front door glass inner weatherstrip with the front door belt seal as shown in the illustration.
67492A
42.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH
Engage the clips to install the front door lower frame bracket garnish.
81080S
43.INSTALL NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ Illumination)
69206B
44.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the claw and guides to install the front door inside handle sub-assembly.
67602
45.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
|
Install in this Direction |
Engage the guides to connect the front door lock remote control cable assembly and front door inside locking cable assembly as shown in the illustration.
w/ Illumination:
Connect the connector.
|
Install in this Direction |
Engage the claws as shown in the illustration.
| *a | Clip (A) |
Engage the clips (A), other clips and guide to install the front door trim board sub-assembly.
Install the 3 screws.
74232
46.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)
Connect the 2 connectors.
|
Install in this Direction |
Engage the guides, clips and claws to install the multiplex network master switch assembly with front door upper armrest base panel as shown in the illustration.
74231
47.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)
Connect the connector.
|
Install in this Direction |
Engage the guides, clips and claws to install the power window regulator switch assembly with front door upper armrest base panel as shown in the illustration.
69284C
48.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG
|
Install in this Direction |
Engage the claws to install the front door inside handle bezel plug as shown in the illustration.
49.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
50.INITIALIZE POWER WINDOW CONTROL SYSTEM
51.INSPECT POWER WINDOW OPERATION
52.INSPECT SRS WARNING LIGHT