Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR
RM32K0E _59 Vehicle Exterior _061791 DOOR / HATCH _0304558 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B332383C04
0.719,0.146 1.031,0.344 0.313,0.198 10 false *a 2.479,0.146 2.792,0.344 0.313,0.198 10 false *b
*a Centering Bolt
*b Standard Bolt


HINT:
·

Centering bolts are used to install the door hinges to the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.

·

The specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSPECT BACK DOOR

a.

Check that the clearance measurements of areas "A" to "O" are within the standard ranges.

B458061N01
3.229,2.844 3.385,3.042 0.156,0.198 10 false G 0.427,0.594 0.583,0.792 0.156,0.198 10 false A 0.865,0.979 1.021,1.177 0.156,0.198 10 false B 1.792,0.604 1.948,0.802 0.156,0.198 10 false C 2.229,1.021 2.385,1.219 0.156,0.198 10 false D 3.198,0.615 3.354,0.813 0.156,0.198 10 false F 3.802,1.115 3.958,1.313 0.156,0.198 10 false E 6.5,1.99 6.656,2.188 0.156,0.198 10 false I 6.104,2.938 6.26,3.135 0.156,0.198 10 false K 6.5,3.24 6.656,3.438 0.156,0.198 10 false J 6.823,4.688 6.979,4.885 0.156,0.198 10 false L 6.094,5.146 6.25,5.344 0.156,0.198 10 false M 5,5.094 5.156,5.292 0.156,0.198 10 false O 5.563,4.688 5.719,4.885 0.156,0.198 10 false N 2.198,4.229 2.354,4.427 0.156,0.198 10 false H

Standard Clearance
Area Measurement Area Measurement
A 7.1 to 11.1 mm (0.280 to 0.437 in.) B -1.0 to 3.0 mm (-0.039 to 0.118 in.)
C 7.1 to 11.1 mm (0.280 to 0.437 in.) D -1.0 to 3.0 mm (-0.039 to 0.118 in.)
E -2.0 to 2.0 mm (-0.079 to 0.079 in.) F 4.0 to 8.0 mm (0.157 to 0.315 in.)
G 3.5 to 8.5 mm (0.138 to 0.335 in.) H 3.5 to 8.5 mm (0.138 to 0.335 in.)
I 3.3 to 7.3 mm (0.130 to 0.287 in.) J 3.5 to 7.5 mm (0.138 to 0.295 in.)
K 2.4 to 5.4 mm (0.094 to 0.213 in.) L 4.0 to 8.0 mm (0.157 to 0.315 in.)
M 2.8 to 5.8 mm (0.110 to 0.228 in.) N 4.0 to 8.0 mm (0.157 to 0.315 in.)
O 3.8 to 6.8 mm (0.150 to 0.268 in.) - -


Hide 64716D 2.REMOVE DECK TRIM REAR COVER

Hide 3.ADJUST BACK DOOR

a.
B458062

Loosen the 4 hinge bolts on the back door and adjust the back door position.


b.

Tighten the 4 hinge bolts on the back door after adjustment.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
B458063

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


d.

Using a brass bar and a hammer, hit the striker to adjust its position.


e.

Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 64716D 4.INSTALL DECK TRIM REAR COVER