Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304569 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch (ON/OFF button) is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch contains momentary type contacts for each function. The contacts close only while the cruise control main switch is being operated in the direction of the relative function arrow, and open when the cruise control main switch is released. The voltage at the terminal of the hybrid vehicle control ECU changes as each of the different contacts open or close. The hybrid vehicle control ECU reads this voltage and controls the SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL functions accordingly.

WIRING DIAGRAM

C367148E03
0.438,1.083 1.115,1.281 0.677,0.198 10 false CANCEL 1.104,1.083 1.563,1.281 0.458,0.198 10 false -SET 1.76,1.083 2.219,1.281 0.458,0.198 10 false +RES 2.396,1.083 3.021,1.281 0.625,0.198 10 false ON/OFF 0.094,1.948 2.563,2.229 2.469,0.281 10 false Cruise Control Main Switch 3.75,0.448 3.896,0.625 0.146,0.177 10 false 3 3.719,0.646 3.896,0.823 0.177,0.177 10 false z4 3.719,1.542 3.896,1.719 0.177,0.177 10 false z4 3.75,1.344 3.896,1.521 0.146,0.177 10 false 4 4.74,0.552 5.094,0.74 0.354,0.188 10 false CCS 4.74,1.458 5.094,1.646 0.354,0.188 10 false ECC 5.26,0.438 5.406,0.615 0.146,0.177 10 false 1 5.188,0.656 5.531,0.833 0.344,0.177 10 false F29 5.188,1.552 5.531,1.729 0.344,0.177 10 false F29 5.271,1.344 5.417,1.521 0.146,0.177 10 false 2 6.135,0.563 6.385,0.74 0.25,0.177 10 false 28 6.385,0.667 6.74,0.854 0.354,0.188 10 false CCS 4.021,1.948 5.125,2.333 1.104,0.385 10 false Spiral Cable Sub-assembly 6.229,1.854 6.573,2.031 0.344,0.177 10 false F2 6.229,2.01 7.156,2.417 0.927,0.406 10 false Hybrid Vehicle Control ECU 3.052,2.073 3.958,2.427 0.906,0.354 10 false Cruise Control Switch Wire 2.99,0.563 3.135,0.74 0.146,0.177 10 false 3 2.99,1.458 3.135,1.635 0.146,0.177 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.READ VALUE ON GTS (CANCEL SWITCH, -SET SWITCH, +RES SWITCH, CRUISE MAIN SWITCH OPERATION CONDITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
-SET Switch -SET switch status ON or OFF ON: -SET switch on
OFF: -SET switch off
-
+RES Switch +RES switch status ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Cruise Main Switch Operation Condition Cruise control main switch (ON/OFF button) status ON or OFF ON: Cruise control main switch (ON/OFF button) pushed
OFF: Cruise control main switch (ON/OFF button) not pushed
-
Powertrain > Cruise Control > Data List
Tester Display
Cancel Switch
-SET Switch
+RES Switch
Cruise Main Switch Operation Condition
50003 399 21,22,23,1

OK:

The Data List items shown in the table change according to the operation of the cruise control main switch.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

Remove the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL


b.

Inspect the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL SWITCH WIRE

NG

3.CHECK CRUISE CONTROL SWITCH WIRE
a.
A306566C77
0.333,1.25 0.833,1.5 0.5,0.25 0.177,0.615 0.49,0.771 0.313,0.156 10 false *a 0.177,2.969 0.49,3.125 0.313,0.156 10 false *b 0.51,1.271 0.823,1.469 0.313,0.198 10 false z4
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Main Switch)


Remove the cruise control switch wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Specified Condition
Cruise control main switch side connector terminal 3 - z4-3 Below 1 Ω
Cruise control main switch side connector terminal 1 - z4-4 Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU AND BODY GROUND)
a.

Disconnect the spiral cable sub-assembly connector.


b.

Disconnect the hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-1 (CCS) - F2-28 (CCS) Always Below 1 Ω
F29-2 (ECC) - Body ground Always Below 1 Ω
F29-1 (CCS) or F2-28 (CCS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR