Home › Engine / Hybrid System › CRUISE CONTROL › SPEED LIMITER SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304570 SPEED LIMITER SYSTEM J

CRUISE CONTROL  SPEED LIMITER SYSTEM  Speed Limiter System does not Operate  


DESCRIPTION

When the speed limiter is turned on using the speed limiter switch, the hybrid vehicle control ECU illuminates the speed limiter indicator and activates the speed limiter system. Each function of the speed limiter system can be activated by operating the cruise control main switch. When the cruise control system is operating, the speed limiter system will not operate.

WIRING DIAGRAM

C367113E02
1.583,0.781 2.479,1.25 0.896,0.469 10 false Speed Limiter Switch 2.792,0.604 3.104,0.802 0.313,0.198 10 false z1 2.792,1.573 3.104,1.771 0.313,0.198 10 false z1 2.833,0.417 3.146,0.615 0.313,0.198 10 false 9 2.833,1.385 3.146,1.583 0.313,0.198 10 false 7 3.573,0.531 3.958,0.719 0.385,0.188 10 false ASL 3.563,1.5 4.01,1.698 0.448,0.198 10 false ECC 4.021,0.604 4.406,0.792 0.385,0.188 10 false F29 4.021,1.573 4.406,1.76 0.385,0.188 10 false F29 4.104,0.417 4.49,0.604 0.385,0.188 10 false 4 4.104,1.385 4.49,1.573 0.385,0.188 10 false 2 5.125,0.531 5.51,0.719 0.385,0.188 10 false 14 5.438,0.625 5.938,0.823 0.5,0.198 10 false ASLM 4.854,1.958 5.354,2.156 0.5,0.198 10 false F2 4.854,2.125 6.708,2.365 1.854,0.24 10 false Hybrid Vehicle Control ECU 2.958,2.135 4.063,2.521 1.104,0.385 10 false Spiral Cable Sub-assembly 1.281,2.125 2.594,2.51 1.313,0.385 10 false Steering Pad Switch Assembly

PROCEDURE

1.CHECK CRUISE CONTROL SYSTEM
a.

Turn the power switch on (IG).


b.

Turn the cruise control on using the cruise control main switch.


c.

Check the operation of each function by operating the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>ROAD TEST


OK:

Each function of the cruise control system operates normally.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (ASL SWITCH)

NG

2.READ VALUE USING GTS (ASL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus : Powertrain / Hybrid Control / Data List / ASL Switch.


e.

According to the display on the GTS, read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ASL Switch Speed limiter switch signal ON or OFF OFF: Speed limiter switch off
ON: Speed limiter switch on
-
Powertrain > Hybrid Control > Data List
Tester Display
ASL Switch
50003 397 33
OK:

The Data List item ASL Switch changes according to the operation of the switch.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the F2 hybrid vehicle control ECU connector.


b.

Disconnect the F29 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-14 (ASLM) - F29-4 (ASL) Always Below 1 Ω
F2-14 (ASLM) or F29-4 (ASL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the F29 spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-2 (ECC) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

6.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

6.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE STEERING PAD SWITCH