Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304571 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the hybrid vehicle control ECU. When the hybrid vehicle control ECU receives the signal, it cancels control of vehicle speed by the dynamic radar cruise control system. The fail-safe function operates to enable normal operation even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake pedal is depressed, voltage is applied to terminal STP of the hybrid vehicle control ECU through the STOP fuse and the stop light switch assembly, and the hybrid vehicle control ECU turns the dynamic radar cruise control system off.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, voltage of STP terminal and that of ST1- terminal of hybrid vehicle control ECU are less than 1 V for approximately 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

Hybrid vehicle control ECU



WIRING DIAGRAM

C367147E01
1.073,0.792 1.521,1.031 0.448,0.24 10 false STOP 0.833,1.448 1.823,1.688 0.99,0.24 10 false ECU-IG2 NO. 3 2.792,0.531 2.958,0.76 0.167,0.229 10 false 7 2.781,1.146 2.948,1.375 0.167,0.229 10 false 6 2.802,1.615 2.969,1.844 0.167,0.229 10 false 2 2.958,0.604 3.125,0.833 0.167,0.229 10 false B 2.958,1.219 3.125,1.448 0.167,0.229 10 false B 2.969,1.698 3.354,1.927 0.385,0.229 10 false GND 3.698,0.573 3.865,0.802 0.167,0.229 10 false L 3.708,1.344 3.875,1.573 0.167,0.229 10 false L 3.875,0.49 4.042,0.719 0.167,0.229 10 false 3 3.875,1.26 4.042,1.49 0.167,0.229 10 false 5 5.313,0.375 5.531,0.604 0.219,0.229 10 false 15 5.281,0.563 5.563,0.781 0.281,0.219 10 false A49 5.313,1.188 5.531,1.417 0.219,0.229 10 false 28 5.281,1.354 5.563,1.573 0.281,0.219 10 false A48 5.635,0.5 6,0.719 0.365,0.219 10 false STP 5.625,1.281 5.99,1.5 0.365,0.219 10 false ST1- 2.844,2.094 3.167,2.292 0.323,0.198 10 false A45 2.833,2.25 3.99,2.698 1.156,0.448 10 false Stop Light Switch Assembly 5.521,2.115 6.927,2.563 1.406,0.448 10 false Hybrid Vehicle Control ECU 3.75,3.24 3.979,3.448 0.229,0.208 10 false 37 3.313,3.313 3.729,3.51 0.417,0.198 10 false STP2 5.417,3.323 5.833,3.521 0.417,0.198 10 false STP1 5.188,3.25 5.417,3.458 0.229,0.208 10 false 25 2.521,3.719 2.844,3.917 0.323,0.198 10 false A39 2.5,3.927 4.583,4.344 2.083,0.417 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.156,3.719 5.479,3.917 0.323,0.198 10 false M67 5.146,3.896 6.667,4.354 1.521,0.458 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
C367136C02
1.469,0.135 1.969,0.385 0.5,0.25 0.677,1.813 1.25,1.104 true 1.958,1.813 2.083,1.104 true 2.615,1.823 2.344,1.083 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 0.406,1.833 0.75,2.01 0.344,0.177 10 false GND 1.906,1.844 2.146,2.021 0.24,0.177 10 false B 2.615,1.833 2.854,2.01 0.24,0.177 10 false B 1.594,0.167 1.938,0.344 0.344,0.177 10 false A45
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A45 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A45-7 (B) - Body ground Power switch off 11 to 14 V
A45-6 (B) - Body ground Power switch on (IG) 11 to 14 V
A45-6 (B) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the stop light switch assembly connector.


c.

Disconnect the brake actuator assembly connector.


d.

Disconnect the certification ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-28 (ST1-) - A45-5 (L) Always Below 1 Ω
A49-15 (STP) - A45-3 (L) Always Below 1 Ω
A48-28 (ST1-) or A45-5 (L) - Body ground Always 10 kΩ or higher
A49-15 (STP) or A45-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR