Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _062180 METER / GAUGE / DISPLAY _0304590 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1500 Fuel Sender Open Detected When IG voltage is 9.5 V or more and the following condition is detected:
·

Average input signal of fuel sender gauge assembly is 630 Ω or more 3 times consecutively


·

Harness or connector

·

Fuel suction tube with pump and gauge assembly

·

Fuel sender gauge assembly

·

Combination meter assembly


-

WIRING DIAGRAM

C369236E03
5.667,1.833 5.833,1.25 true 0.604,1.885 2.292,2.083 1.688,0.198 10 false M14 0.604,2.052 4.177,2.292 3.573,0.24 10 false Fuel Suction Tube with Pump and Gauge Assembly 0.969,1.094 2.198,1.583 1.229,0.49 10 false Fuel Sender Gauge Assembly 2.406,0.948 2.573,1.135 0.167,0.188 10 false 1 2.396,1.49 2.563,1.677 0.167,0.188 10 false 2 2.76,1.094 2.927,1.281 0.167,0.188 10 false 3 3.063,0.76 3.333,0.979 0.271,0.219 10 false FR 3.042,1.125 3.313,1.344 0.271,0.219 10 false FV 3.063,1.5 3.333,1.719 0.271,0.219 10 false FE 3.354,0.729 3.521,0.917 0.167,0.188 10 false 3 3.344,1.125 3.51,1.313 0.167,0.188 10 false 1 3.354,1.5 3.521,1.688 0.167,0.188 10 false 2 4.458,0.729 4.74,0.917 0.281,0.188 10 false 23 4.438,1.104 4.719,1.292 0.281,0.188 10 false 16 4.438,1.51 4.719,1.698 0.281,0.188 10 false 15 4.729,0.74 5,0.958 0.271,0.219 10 false FR 4.729,1.104 5,1.323 0.271,0.219 10 false FV 4.719,1.5 5.229,1.729 0.51,0.229 10 false FE&B 5.24,0.792 5.51,1.01 0.271,0.219 10 false I/F 5.25,1.177 5.521,1.396 0.271,0.219 10 false I/F 5.802,1.531 6.229,1.76 0.427,0.229 10 false CPU 4.729,1.813 5.906,2.021 1.177,0.208 10 false Fuel Controller 4.688,2.177 5.115,2.406 0.427,0.229 10 false F4 4.667,2.344 6.781,2.698 2.115,0.354 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0 L, Max.: 127.5 L
·

Fuel receiver gauge indicates

F: 38.3 L

·

Fuel receiver gauge indicates

3/4: 30.1 L

·

Fuel receiver gauge indicates

1/2: 21.3 L

·

Fuel receiver gauge indicates

1/4: 12.4 L

·

Fuel receiver gauge indicates

E: 4.3 L


-
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data can be displayed on the GTS A
Fuel level data cannot be displayed on the GTS B



A

REPLACE COMBINATION METER ASSEMBLY

B

2.INSPECT FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)
2.INSPECT FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)
E284677C26
1.5,0.208 1.906,0.458 0.406,0.25 1.26,1.625 1.156,1 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.625,0.25 1.927,0.479 0.302,0.229 10 false F4 1.188,1.688 1.5,1.844 0.313,0.156 10 false FV
*a Component with harness connected
(Combination Meter Assembly)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-16 (FV) - Body ground Power switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT FUEL SENDER GAUGE ASSEMBLY
E284677C27
1.5,0.208 1.906,0.458 0.406,0.25 2.458,1.115 2.208,1.698 true 1.26,1 1.292,1.708 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.635,0.25 1.979,0.479 0.344,0.229 10 false F4 1.042,1.75 1.552,1.958 0.51,0.208 10 false FE&B 2.146,1.75 2.458,1.906 0.313,0.156 10 false FR
*a Component with harness connected
(Combination Meter Assembly)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-23 (FR) - F4-15 (FE&B) Power switch on (IG) 0.2 to 4.7 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the M14 fuel suction tube with pump and gauge assembly connector.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M14-3 (FR) - F4-23 (FR) Always Below 1 Ω
M14-2 (FE) - F4-15 (FE&B) Always Below 1 Ω
M14-1 (FV) - F4-16 (FV) Always Below 1 Ω
F4-23 (FR) - Body ground Always 10 kΩ or higher
F4-15 (FE&B) - Body ground Always 10 kΩ or higher
F4-16 (FV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2ZR-FXE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2ZR-FXE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

6.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

6.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
E158805C69
0.333,1.25 0.833,1.5 0.5,0.25 0.333,3.667 0.75,3.917 0.417,0.25 2.083,1.271 2.417,0.917 true 1.719,1.229 2.083,0.5 true 1.354,1.26 1.021,0.906 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.458,1.302 0.896,1.531 0.438,0.229 10 false M14 0.51,3.729 0.844,3.979 0.333,0.25 10 false A 0.813,0.74 1.146,0.99 0.333,0.25 10 false FR 2.125,0.365 2.458,0.615 0.333,0.25 10 false FE 2.458,0.792 2.792,1.042 0.333,0.25 10 false FV
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M14-1 (FV) - A-3 Always Below 1 Ω
M14-2 (FE) - A-2 Always Below 1 Ω
M14-3 (FR) - A-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY