The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor LH, No. 1 side airbag sensor LH and No. 2 side airbag sensor LH.
The door side airbag sensor LH, No. 1 side airbag sensor LH and No. 2 side airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the door side airbag sensor LH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B167A/5A | Front Door Pressure Sensor LH | Any of the following conditions is met:
·
Door side airbag sensor LH malfunction ·
Airbag sensor assembly malfunction |
·
Door side airbag sensor LH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| B167E/5A | Front Door Pressure Sensor Threshold Malfunction (LH) | Any of the following conditions is met:
·
Door side airbag sensor LH malfunction ·
Airbag sensor assembly malfunction |
·
Door side airbag sensor LH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Power switch on (IG) | ○ | ○ |
| Malfunction Status | Door side airbag sensor LH malfunction | ○ | - |
| Airbag sensor assembly malfunction | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Power switch on (IG) | ○ | ○ |
| Malfunction Status | Door side airbag sensor LH malfunction | ○ | - |
| Airbag sensor assembly malfunction | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor LH |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminals to disable the SRS system.
Interchange the door side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B166C/4A, B166F/4A, B167A/5A and B167E/5A may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B167A/5A or B167E/5A is output. | A |
| DTC B166C/4A or B166F/4A is output. | B |
| DTCs B166C/4A, B166F/4A, B167A/5A and B167E/5A are not output. | C |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the door side airbag sensor LH and RH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING