Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › from 2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13A7  Actuator Malfunction  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13A7 Actuator Malfunction Both of following conditions are met:
1.

Electric parking brake is operating

2.

One of following is detected: Motor lock, gear lock, motor spinning or repeated slipping


·

Parking brake actuator assembly

·

Rear brake

·

Wire harness or connector


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Electric parking brake is operating ○ ○ ○ ○
Malfunction Status Motor lock is detected ○ - - -
Gear lock is detected - ○ - -
Motor spinning is detected - - ○ -
Repeated slipping is detected - - - ○
Detection Time - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

This DTC may be stored when the system changes to pad replacement mode, but this is not a malfunction.

·

This DTC may be stored when the parking brake is forcibly released, but this is not a malfunction.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the power switch is first turned on (IG).



PROCEDURE

1.CHECK DTC
a.

Check for DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Result Proceed to
Only DTC C13A7 is output A
DTCs other than C13A7 are output B



A

2.READ VALUE USING GTS (PERMISSION OF RH INTERLOCKING PKB LOCK / PERMISSION OF LH INTERLOCKING PKB LOCK)

B

2.READ VALUE USING GTS (PERMISSION OF RH INTERLOCKING PKB LOCK / PERMISSION OF LH INTERLOCKING PKB LOCK)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Permission of RH Interlocking PKB Lock Parking brake actuator assembly RH parking brake lock control permission status OK or NG OK -
Permission of LH Interlocking PKB Lock Parking brake actuator assembly LH parking brake lock control permission status OK or NG OK -
Chassis > Electric Parking Brake > Data List
Tester Display
Permission of RH Interlocking PKB Lock
Permission of LH Interlocking PKB Lock
50003 184 632,636
Result:
Proceed to
NEXT




NEXT

3.INSPECT PARKING BRAKE WIRE ASSEMBLY
3.INSPECT PARKING BRAKE WIRE ASSEMBLY
C393536C02
1.833,0.333 2.167,0.583 0.333,0.25 1.833,0.667 2.167,0.917 0.333,0.25 5,0.5 5.333,0.75 0.333,0.25 5,0.167 5.333,0.417 0.333,0.25 1.396,2.167 1.896,1.604 true 2.625,2.167 2.135,1.604 true 4.5,2.156 5,1.594 true 5.823,2.156 5.333,1.594 true 1.885,1.469 1.396,0.906 true 2.135,1.469 2.635,0.906 true 5,1.427 4.51,0.865 true 5.323,1.417 5.823,0.854 true 1.875,0.385 2.333,0.583 0.458,0.198 10 false dM3 1.875,0.719 2.333,0.917 0.458,0.198 10 false eM3 5.094,0.219 5.406,0.417 0.313,0.198 10 false d2 5.094,0.552 5.406,0.75 0.313,0.198 10 false e2 5.417,0.219 5.729,0.417 0.313,0.198 10 false *d 5.417,0.552 5.729,0.75 0.313,0.198 10 false *e 5.083,2.281 5.396,2.479 0.313,0.198 10 false *c 5.854,2.188 6.531,2.385 0.677,0.198 10 false MRL+*e 4.031,2.167 4.635,2.365 0.604,0.198 10 false MRL-*e 2.677,2.188 3.229,2.396 0.552,0.208 10 false MRL-*e 1.948,2.271 2.26,2.469 0.313,0.198 10 false *b 0.865,2.167 1.427,2.375 0.563,0.208 10 false MRL+*e 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.25,0.396 2.563,0.594 0.313,0.198 10 false *d 2.24,0.729 2.552,0.927 0.313,0.198 10 false *e 0.875,0.74 1.438,0.948 0.563,0.208 10 false MRR+*d 2.677,0.76 3.229,0.969 0.552,0.208 10 false MRR-*d 5.854,0.688 6.417,0.896 0.563,0.208 10 false MRR+*d 4,0.719 4.552,0.927 0.552,0.208 10 false MRR-*d
*a Front view of Parking Brake Wire Assembly *b (to wire harness connector)
*c (to Parking Brake Actuator Assembly) *d RH
*e LH - -


a.

Remove the parking brake wire assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


b.

Check the parking brake wire assembly for damage.

OK:

No damage.


HINT:

If damaged, there may be a short in the wire harness or a short to ground.



c.

Inspect the parking brake wire assembly.

Standard Resistance:
RH
Tester Connection Condition Specified Condition
dM3-2 (MRR-) - d2-1 (MRR-) Always Below 1 Ω
dM3-2 (MRR-) - d2-2 (MRR+) Always 10 kΩ or higher
dM3-2 (MRR-) or d2-1 (MRR-) - Body ground Always 10 kΩ or higher
dM3-1 (MRR+) - d2-2 (MRR+) Always Below 1 Ω
dM3-1 (MRR+) - d2-1 (MRR-) Always 10 kΩ or higher
dM3-1 (MRR+) or d2-2 (MRR+) - Body ground Always 10 kΩ or higher

LH
Tester Connection Condition Specified Condition
eM3-2 (MRL-) - e2-1 (MRL-) Always Below 1 Ω
eM3-2 (MRL-) - e2-2 (MRL+) Always 10 kΩ or higher
eM3-2 (MRL-) or e2-1 (MRL-) - Body ground Always 10 kΩ or higher
eM3-1 (MRL+) - e2-2 (MRL+) Always Below 1 Ω
eM3-1 (MRL+) - e2-1 (MRL-) Always 10 kΩ or higher
eM3-1 (MRL+) or e2-2 (MRL+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE PARKING BRAKE WIRE ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY)
a.

Turn the power switch off.


b.

Make sure the parking brake wire assembly is securely installed.


c.

Disconnect the A84*2 or A85*1 parking brake ECU (brake actuator assembly) connector.

*1: for LHD

*2: for RHD



d.

Disconnect the d2*1 or e2*2 parking brake actuator assembly connector.

*1: for RH

*2: for LH



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD RH Side
Tester Connection Condition Specified Condition
A85-4 (MRR+) - d2-2 (MRR+) Always Below 1 Ω
A85-3 (MRR-) - d2-1 (MRR-) Always Below 1 Ω
A85-4 (MRR+) or d2-2 (MRR+) - Body ground Always 10 kΩ or higher
A85-3 (MRR-) or d2-1 (MRR-) - Body ground Always 10 kΩ or higher

for LHD LH Side
Tester Connection Condition Specified Condition
A85-7 (MRL+) - e2-2 (MRL+) Always Below 1 Ω
A85-8 (MRL-) - e2-1 (MRL-) Always Below 1 Ω
A85-7 (MRL+) or e2-2 (MRL+) - Body ground Always 10 kΩ or higher
A85-8 (MRL-) or e2-1 (MRL-) - Body ground Always 10 kΩ or higher

for RHD RH Side
Tester Connection Condition Specified Condition
A84-4 (MRR+) - d2-2 (MRR+) Always Below 1 Ω
A84-3 (MRR-) - d2-1 (MRR-) Always Below 1 Ω
A84-4 (MRR+) or d2-2 (MRR+) - Body ground Always 10 kΩ or higher
A84-3 (MRR-) or d2-1 (MRR-) - Body ground Always 10 kΩ or higher

for RHD LH Side
Tester Connection Condition Specified Condition
A84-7 (MRL+) - e2-2 (MRL+) Always Below 1 Ω
A84-8 (MRL-) - e2-1 (MRL-) Always Below 1 Ω
A84-7 (MRL+) or e2-2 (MRL+) - Body ground Always 10 kΩ or higher
A84-8 (MRL-) or e2-1 (MRL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT REAR BRAKE AND PARKING BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT REAR BRAKE AND PARKING BRAKE ACTUATOR ASSEMBLY
a.

Enter rear brake pad replacement mode.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>TEST MODE PROCEDURE


b.

Turn the power switch off.


c.

Check that the rotating parts are not seized or the actuator is not spinning freely.

i.

Check that the parking brake actuator assembly is installed properly to the rear brake caliper and that it is not spinning freely.

For the parking brake actuator assembly removal procedure: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


ii.

Check that there is no damage to the rotating parts from the parking brake actuator assembly to the rear brake caliper.


iii.

Inspect the parking brake actuator assembly and check that it operates correctly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION


iv.

Check that the rear brake caliper threaded part rotates and that the rear disc brake piston moves outward.

HINT:

For the check procedures, refer to the parking brake forced release method when not using the GTS.

Click hereBrake>PARKING BRAKE>FORCED RELEASE>OPERATION METHOD




HINT:

Return to normal mode after work is complete.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>TEST MODE PROCEDURE


Result:
Proceed to
OK
NG



OK

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE NECESSARY PARTS