Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › from 2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  Electric Parking Brake AUTO Indicator Light Circuit  


DESCRIPTION

Pulling the electric parking brake switch to the lock side for 5 seconds or more changes the AUTO function (shift-linked function) to ON, and an AUTO Mode ON message is displayed on the multi-information display in the combination meter.

Pressing the electric parking brake switch to the release side for 5 seconds or more changes the AUTO function (shift-linked function) to OFF, and an AUTO Mode OFF message is displayed on the multi-information display in the combination meter.

WIRING DIAGRAM

C393513E01
0.063,3.438 0.521,3.635 0.458,0.198 10 false F67 0.063,3.604 2.438,4.052 2.375,0.448 10 false Electric Parking Brake Switch (Electric Parking Brake Switch Assembly) 3.198,3.083 3.656,3.281 0.458,0.198 10 false A85 3.563,3.083 4.021,3.281 0.458,0.198 10 false A84 3.198,2.417 3.656,2.615 0.458,0.198 10 false A85 3.563,2.417 4.021,2.615 0.458,0.198 10 false A84 3.563,1.781 4.021,1.979 0.458,0.198 10 false A84 3.552,1.104 4.01,1.302 0.458,0.198 10 false A84 3.198,1.781 3.656,1.979 0.458,0.198 10 false A85 1.823,1 2.281,1.198 0.458,0.198 10 false SWI1 1.74,1.667 2.198,1.865 0.458,0.198 10 false SWO1 1.74,2.969 2.198,3.167 0.458,0.198 10 false SWO2 1.823,2.292 2.281,2.49 0.458,0.198 10 false SWI2 3.188,1.104 3.646,1.302 0.458,0.198 10 false A85 3.219,0.896 3.531,1.094 0.313,0.198 10 false 14 3.583,0.896 3.896,1.094 0.313,0.198 10 false 14 2.302,1 2.615,1.198 0.313,0.198 10 false 6 2.302,1.677 2.615,1.875 0.313,0.198 10 false 5 2.302,2.292 2.615,2.49 0.313,0.198 10 false 4 2.302,2.969 2.615,3.167 0.313,0.198 10 false 3 3.24,1.563 3.552,1.76 0.313,0.198 10 false 20 3.594,1.563 3.906,1.76 0.313,0.198 10 false 20 3.24,2.198 3.552,2.396 0.313,0.198 10 false 24 3.604,2.198 3.917,2.396 0.313,0.198 10 false 24 3.24,2.865 3.552,3.063 0.313,0.198 10 false 22 3.594,2.865 3.906,3.063 0.313,0.198 10 false 22 3.906,1.104 4.365,1.302 0.458,0.198 10 false SWI1 3.906,1.781 4.365,1.979 0.458,0.198 10 false SWO1 3.917,2.417 4.375,2.615 0.458,0.198 10 false SWI2 3.906,3.073 4.365,3.271 0.458,0.198 10 false SWO2 3.375,4.802 5.031,5.271 1.656,0.469 10 false Parking Brake ECU (Brake Actuator Assembly) 5.094,4.885 7.156,5.271 2.063,0.385 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.323,3.573 6.958,3.938 1.635,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 5.271,2.365 7.042,2.583 1.771,0.219 10 false Hybrid Vehicle Control ECU 5.208,1.125 7.083,1.344 1.875,0.219 10 false Combination Meter Assembly 0.865,5.323 2.667,5.563 1.802,0.24 10 false : CAN Communication Line 3.229,1.323 3.542,1.521 0.313,0.198 10 false *1 3.594,1.323 3.906,1.521 0.313,0.198 10 false *2 3.24,1.99 3.552,2.188 0.313,0.198 10 false *1 3.25,2.625 3.563,2.823 0.313,0.198 10 false *1 3.24,3.292 3.552,3.49 0.313,0.198 10 false *1 3.604,1.99 3.917,2.188 0.313,0.198 10 false *2 3.604,2.625 3.917,2.823 0.313,0.198 10 false *2 3.615,3.292 3.927,3.49 0.313,0.198 10 false *2 0.427,4.667 1.323,4.885 0.896,0.219 10 false *1: for LHD 0.417,4.969 1.313,5.188 0.896,0.219 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly), as the parking brake indicator light (red) blinks when the power switch is first turned on (IG).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS (AUTO MODE)

B

2.READ VALUE USING GTS (AUTO MODE)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and the GTS on.


d.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


e.

Check the values by referring to the table below.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto Mode AUTO (shift-linked) mode permission status OFF or ON OFF: Manual mode
ON: AUTO (shift-linked) mode
-
Chassis > Electric Parking Brake > Data List
Tester Display
Auto Mode
50003 184 628

f.

When switching the mode, check that the Data List display turns on and off.


Result:
Result Proceed to
AUTO indicator light does not illuminate and turn off according to turning Active Test on and off A
AUTO indicator light illuminates and turns off according to turning Active Test on and off B



A

3.CHECK DTC

B

6.PERFORM ACTIVE TEST USING GTS (AUTO MODE)
3.CHECK DTC
a.

Check for DTCs.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > Electric Parking Brake > Trouble Codes
50001 184

Result:
Result Proceed to
DTC is not output A
DTC is output B



A

4.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

B

4.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Inspect the electric parking brake switch (electric parking brake switch assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the F67 electric parking brake switch (electric parking brake switch assembly) connector.


b.

Disconnect the A84*2 or A85*1 parking brake ECU (brake actuator assembly) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A85-14 (SWI1) - F67-6 (SWI1) Always Below 5 Ω
A85-20 (SWO1) - F67-5 (SWO1) Always Below 5 Ω
A85-14 (SWI1) or F67-6 (SWI1) - Body ground Always 10 kΩ or higher
A85-20 (SWO1) or F67-5 (SWO1) - Body ground Always 10 kΩ or higher
A85-24 (SWI2) - F67-4 (SWI2) Always Below 5 Ω
A85-22 (SWO2) - F67-3 (SWO2) Always Below 5 Ω
A85-24 (SWI2) or F67-4 (SWI2) - Body ground Always 10 kΩ or higher
A85-22 (SWO2) or F67-3 (SWO2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A84-14 (SWI1) - F67-6 (SWI1) Always Below 5 Ω
A84-20 (SWO1) - F67-5 (SWO1) Always Below 5 Ω
A84-14 (SWI1) or F67-6 (SWI1) - Body ground Always 10 kΩ or higher
A84-20 (SWO1) or F67-5 (SWO1) - Body ground Always 10 kΩ or higher
A84-24 (SWI2) - F67-4 (SWI2) Always Below 5 Ω
A84-22 (SWO2) - F67-3 (SWO2) Always Below 5 Ω
A84-24 (SWI2) or F67-4 (SWI2) - Body ground Always 10 kΩ or higher
A84-22 (SWO2) or F67-3 (SWO2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (AUTO MODE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.PERFORM ACTIVE TEST USING GTS (AUTO MODE)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Active Test.


f.

Perform the Active Test according to the display on the GTS.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > Electric Parking Brake > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Auto Mode AUTO (shift-linked) mode ON or OFF
·

Vehicle stopped

·

Power switch on (IG)


Chassis > Electric Parking Brake > Active Test
Tester Display
Auto Mode
50004 184 27

g.

Select the Data List on the GTS.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
AUTO Indicator AUTO indicator light output signal OFF or ON - -
Chassis > Electric Parking Brake > Data List
Tester Display
AUTO Indicator
50003 184 644

h.

When turning the Active Test ON and OFF, check that the AUTO indicator light illuminates and turns off.


Result:
Result Proceed to
AUTO indicator light does not illuminate and turn off according to turning Active Test ON and OFF. (for LHD) A
AUTO indicator light does not illuminate and turn off according to turning Active Test ON and OFF. (for RHD) B
AUTO indicator light illuminates and turns off according to turning Active Test ON and OFF. C



A

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

B

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

C

7.INSPECT COMBINATION METER ASSEMBLY
7.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7

b.

Check the multi-information display the combination meter assembly turn ON or OFF in accordance with the GTS operation.

OK:

The message in the multi-information display appears and disappears in accordance with the Active Test operation.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

B

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

C