When the electric parking brake switch is pulled, a lock request signal is sent from the parking brake ECU (brake actuator assembly) to the parking brake actuator assembly. When the electric parking brake switch is pushed, a release request signal is sent from the parking brake ECU (brake actuator assembly) to the parking brake actuator assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C13B4 | EPB Switch Malfunction | ·
Parking brake switch open or short circuit is detected for 0.3 seconds or more ·
Parking brake switch stuck malfunction |
·
Electric parking brake switch (electric parking brake switch assembly) ·
Wire harness or connector ·
Parking brake ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | - | - | - | - |
| Malfunction Status | Parking brake switch open circuit is detected | ○ | - | - |
| Parking brake switch short circuit is detected | - | ○ | - | |
| Parking brake switch stuck malfunction | - | - | ○ | |
| Detection Time | 0.3 seconds or more | 0.3 seconds or more | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.
When replacing the parking brake ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the power switch is first turned on (IG).
Inspect the electric parking brake switch (electric parking brake switch assembly).
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F67 electric parking brake switch (electric parking brake switch assembly) connector.
Disconnect the A84*2 or A85*1 parking brake ECU (brake actuator assembly) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A85-14 (SWI1) - F67-6 (SWI1) | Always | Below 5 Ω |
| A85-20 (SWO1) - F67-5 (SWO1) | Always | Below 5 Ω |
| A85-24 (SWI2) - F67-4 (SWI2) | Always | Below 5 Ω |
| A85-22 (SWO2) - F67-3 (SWO2) | Always | Below 5 Ω |
| A85-14 (SWI1) or F67-6 (SWI1) - Body ground | Always | 10 kΩ or higher |
| A85-20 (SWO1) or F67-5 (SWO1) - Body ground | Always | 10 kΩ or higher |
| A85-24 (SWI2) or F67-4 (SWI2) - Body ground | Always | 10 kΩ or higher |
| A85-22 (SWO2) or F67-3 (SWO2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A84-14 (SWI1) - F67-6 (SWI1) | Always | Below 5 Ω |
| A84-20 (SWO1) - F67-5 (SWO1) | Always | Below 5 Ω |
| A84-24 (SWI2) - F67-4 (SWI2) | Always | Below 5 Ω |
| A84-22 (SWO2) - F67-3 (SWO2) | Always | Below 5 Ω |
| A84-14 (SWI1) or F67-6 (SWI1) - Body ground | Always | 10 kΩ or higher |
| A84-20 (SWO1) or F67-5 (SWO1) - Body ground | Always | 10 kΩ or higher |
| A84-24 (SWI2) or F67-4 (SWI2) - Body ground | Always | 10 kΩ or higher |
| A84-22 (SWO2) or F67-3 (SWO2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG).
Check for DTCs.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are output (for LHD) | A |
| DTCs are output (for RHD) | B |
| DTCs are not output | C |
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING