Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2018.05–2019.09
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292486 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P070562  Transmission Range Sensor "A" Circuit (PRNDL Input) Signal Compare Failure  


DESCRIPTION

The shift lever position sensor sends 7 different switch signals to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses these signals to detect the shift lever position (P, R, N, D or B). The hybrid vehicle control ECU also uses this information to determine the intended direction of travel (forward or reverse).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P070562 Transmission Range Sensor "A" Circuit (PRNDL Input) Signal Compare Failure Shift sensor circuit malfunction (abnormal pattern)
A malfunction in the P, R, N, D or B circuit is detected based on the shift sensor input pattern.
(1 trip detection logic)
·

Wire harness or connector

·

Shift lever position sensor

·

Hybrid vehicle control ECU


Does not come on Master Warning:
Comes on

Related Data List
DTC No. ECU Data List
P070562
·

Shift Position Sensor (PNB)

·

Shift Position Sensor (PR)

·

Shift Position Sensor (DB2)

·

Shift Position Sensor (DB1)

·

Shift Position Sensor (N)

·

Shift Position Sensor (R)

·

Shift Position Sensor (P)

·

Shift Position



WIRING DIAGRAM

A394804E01
0.51,4.135 2.302,4.417 1.792,0.281 10 false Shift Lever Position Sensor 0.51,3.979 2.302,4.26 1.792,0.281 10 false C36 4.865,4.167 6.656,4.448 1.792,0.281 10 false Hybrid Vehicle Control ECU 4.875,4 6.427,4.208 1.552,0.208 10 false A48 1.76,3.167 2.219,3.365 0.458,0.198 10 false PNB 1.844,2.792 2.302,2.99 0.458,0.198 10 false PR 1.781,2.448 2.24,2.646 0.458,0.198 10 false DB2 1.792,2.104 2.25,2.302 0.458,0.198 10 false DB1 1.948,1.781 2.406,1.979 0.458,0.198 10 false N 1.938,1.396 2.396,1.594 0.458,0.198 10 false R 1.948,1.052 2.406,1.25 0.458,0.198 10 false P 4.833,3.146 5.281,3.333 0.448,0.188 10 false PNB 2.198,1.052 2.5,1.25 0.302,0.198 10 false 8 2.198,1.396 2.479,1.573 0.281,0.177 10 false 9 2.198,1.781 2.521,1.979 0.323,0.198 10 false 2 2.198,2.104 2.438,2.302 0.24,0.198 10 false 1 2.198,2.448 2.51,2.635 0.313,0.188 10 false 6 2.198,2.781 2.5,2.969 0.302,0.188 10 false 3 2.198,3.167 2.458,3.354 0.26,0.188 10 false 4 4.833,2.792 5.313,2.99 0.479,0.198 10 false PR 4.833,2.458 5.302,2.646 0.469,0.188 10 false DB2 4.833,2.115 5.396,2.323 0.563,0.208 10 false DB1 4.833,1.792 5.24,1.979 0.406,0.188 10 false N 4.833,1.406 5.323,1.635 0.49,0.229 10 false R 4.833,1.063 5.25,1.292 0.417,0.229 10 false P 4.531,1.063 4.979,1.25 0.448,0.188 10 false 21 4.531,1.396 5,1.573 0.469,0.177 10 false 15 4.531,1.792 5.031,1.969 0.5,0.177 10 false 20 4.531,2.115 4.948,2.302 0.417,0.188 10 false 26 4.531,2.458 4.938,2.667 0.406,0.208 10 false 14 4.531,2.792 5,3.021 0.469,0.229 10 false 17 4.531,3.156 4.979,3.365 0.448,0.208 10 false 34 1.865,0.542 2.323,0.74 0.458,0.198 10 false +B 2.198,0.542 2.5,0.74 0.302,0.198 10 false 7 4.604,0.542 5.052,0.729 0.448,0.188 10 false 1 4.833,0.625 5.406,0.865 0.573,0.24 10 false PSFT

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG).

2.

Slowly move the shift lever from P to B then back to P.



PROCEDURE

1.READ VALUE USING GTS (SHIFT SENSOR SW)
a.

Connect the GTS the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Position Sensor (PNB), Shift Position Sensor (PR), Shift Position Sensor (DB2), Shift Position Sensor (DB1), Shift Position Sensor (N), Shift Position Sensor (R), Shift Position Sensor (P).

Powertrain > Hybrid Control > Data List
Tester Display
Shift Position Sensor (PNB)
Shift Position Sensor (PR)
Shift Position Sensor (DB1)
Shift Position Sensor (DB2)
Shift Position Sensor (N)
Shift Position Sensor (R)
Shift Position Sensor (P)
50003 397 400,401,403,402,404,405,406

d.

While slowly moving the shift lever from P to B, then back to P, read the Data List (Shift Sensor SW) displayed on the GTS.

HINT:

Be sure to move the shift lever slowly.


Result:
ECU Data List Shift Position
P R N D B
Shift Position Sensor (P) ON OFF OFF OFF OFF
Shift Position Sensor (R) OFF ON OFF OFF OFF
Shift Position Sensor (PR) ON ON OFF OFF OFF
Shift Position Sensor (N) OFF OFF ON OFF OFF
Shift Position Sensor (DB1) OFF OFF OFF ON ON
Shift Position Sensor (DB2) OFF OFF OFF ON ON
Shift Position Sensor (PNB) ON OFF ON OFF ON



e.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 236
OK:

DTC P070562 is not output.



f.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK FOR INTERMITTENT PROBLEMS

NG

3.CHECK SHIFT LEVER POSITION SENSOR
2.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

3.CHECK SHIFT LEVER POSITION SENSOR
a.

Turn the power switch on (IG).


b.
A389500C15
1.167,0.417 1.667,0.667 0.5,0.25 1.583,2.573 1.615,1.854 true 2.083,2.583 1.667,1.854 true 0.833,2.5 1.198,1.833 true 1.167,2.5 1.208,1.906 true 1.25,1.781 0.76,1.01 true 1.344,1.771 1.167,1.01 true 1.396,1.771 1.667,1.021 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.542,2.625 1.854,2.781 0.313,0.156 10 false P 2.073,2.625 2.25,2.823 0.177,0.198 10 false N 1.031,2.542 1.427,2.708 0.396,0.167 10 false PNB 0.615,2.531 1.01,2.698 0.396,0.167 10 false DB1 0.51,0.875 0.906,1.042 0.396,0.167 10 false PR 1.031,0.844 1.427,1.01 0.396,0.167 10 false R 1.729,0.844 2.125,1.01 0.396,0.167 10 false DB2 1.302,0.458 1.698,0.625 0.396,0.167 10 false A48
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A48-21 (P) - Body ground Power switch on (IG)
Shift lever in P
6 to 14 V
Power switch on (IG)
Shift lever in any position except P
0 to 1.5 V
A48-15 (R) - Body ground Power switch on (IG)
Shift lever in R
6 to 14 V
Power switch on (IG)
Shift lever in any position except R
0 to 1.5 V
A48-17 (PR) - Body ground Power switch on (IG)
Shift lever in P or R
6 to 14 V
Power switch on (IG)
Shift lever in any position except P or R
0 to 1.5 V
A48-20 (N) - Body ground Power switch on (IG)
Shift lever in N
6 to 14 V
Power switch on (IG)
Shift lever in any position except N
0 to 1.5 V
A48-26 (DB1) - Body ground Power switch on (IG)
Shift lever in D or B
6 to 14 V
Power switch on (IG)
Shift lever in any position except D or B
0 to 1.5 V
A48-14 (DB2) - Body ground Power switch on (IG)
Shift lever in D or B
6 to 14 V
Power switch on (IG)
Shift lever in any position except D or B
0 to 1.5 V
A48-34 (PNB) - Body ground Power switch on (IG)
Shift lever in P, N or B
6 to 14 V
Power switch on (IG)
Shift lever in any position except P, N or B
0 to 1.5 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
A394801

Disconnect the shift lever position sensor connector.

Click hereDrivetrain>P610 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT LEVER POSITION SENSOR>REMOVAL


b.

Turn the power switch on (IG).


c.
A210242C20
1.438,0.167 1.938,0.417 0.5,0.25 1.76,1.417 1.896,1.875 true 1.823,1.896 2.302,2.177 0.479,0.281 10 false +B 0.229,0.125 0.708,0.458 0.479,0.333 10 false *a 1.563,0.188 2.042,0.438 0.479,0.25 10 false C36
*a Front view of wire harness connector
(to Shift Lever Position Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C36-7 (+B) - Body ground Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the shift lever position sensor connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Reconnect the shift lever position sensor connector.


Result:
Proceed to
OK
NG



OK

5.INSPECT SHIFT LEVER POSITION SENSOR

NG

6.CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - HYBRID VEHICLE CONTROL ECU)
5.INSPECT SHIFT LEVER POSITION SENSOR
a.
A394801

Disconnect the shift lever position sensor connector.


b.
A264044C17
2.833,1.083 3.333,1.333 0.5,0.25 1.969,1.469 2.208,1.854 true 1.719,1.458 1.792,1.896 true 1.479,1.458 1.448,1.865 true 1.323,1.458 1.104,1.875 true 1.25,1.125 0.729,0.75 true 1.365,1.125 1.042,0.469 true 1.667,1.146 1.792,0.448 true 1.938,1.146 2.26,0.573 true 2.958,1.104 3.344,1.333 0.385,0.229 10 false C36 0.094,0.052 0.531,0.385 0.438,0.333 10 false *a 0.385,0.688 0.823,0.969 0.438,0.281 10 false PNB 0.802,0.375 1.167,0.677 0.365,0.302 10 false PR 1.865,0.333 2.177,0.635 0.313,0.302 10 false N 2.333,0.469 2.688,0.74 0.354,0.271 10 false DB1 2.167,1.896 2.615,2.094 0.448,0.198 10 false DB2 1.719,1.927 2.031,2.125 0.313,0.198 10 false +B 1.406,1.917 1.677,2.125 0.271,0.208 10 false P 1.031,1.906 1.292,2.104 0.26,0.198 10 false R
*a Component without harness connected
(Shift Lever Position Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-7 (+B) - C36-3 (PR) Shift lever in P Below 1 Ω
C36-7 (+B) - C36-4 (PNB) Below 1 Ω
C36-7 (+B) - C36-8 (P) Below 1 Ω
C36-7 (+B) - C36-1 (DB1), C36-2 (N), C36-6 (DB2) and C36-9 (R) 10 kΩ or higher
C36-7 (+B) - C36-3 (PR) Shift lever in R Below 1 Ω
C36-7 (+B) - C36-9 (R) Below 1 Ω
C36-7 (+B) - C36-1 (DB1), C36-2 (N), C36-4 (PNB), C36-6 (DB2) and C36-8 (P) 10 kΩ or higher
C36-7 (+B) - C36-2 (N) Shift lever in N Below 1 Ω
C36-7 (+B) - C36-4 (PNB) Below 1 Ω
C36-7 (+B) - C36-1 (DB1), C36-3 (PR), C36-6 (DB2), C36-8 (P) and C36-9 (R) 10 kΩ or higher
C36-7 (+B) - C36-1 (DB1) Shift lever in D Below 1 Ω
C36-7 (+B) - C36-6 (DB2) Below 1 Ω
C36-7 (+B) - C36-2 (N), C36-3 (PR), C36-4 (PNB), C36-8 (P) and C36-9 (R) 10 kΩ or higher
C36-7 (+B) - C36-1 (DB1) Shift lever in B Below 1 Ω
C36-7 (+B) - C36-4 (PNB) Below 1 Ω
C36-7 (+B) - C36-6 (DB2) Below 1 Ω
C36-7 (+B) - C36-2 (N), C36-3 (PR), C36-8 (P) and C36-9 (R) 10 kΩ or higher


HINT:

Terminal No.5 on the component side connector is empty.



c.

Reconnect the shift lever position sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (SHIFT LEVER POSITION SENSOR - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the shift lever position sensor connector.


b.

Disconnect the hybrid vehicle control ECU connector.


c.
A394805C01
1.438,0.083 1.938,0.333 0.5,0.25 1.135,2.167 1.635,2.417 0.5,0.25 2.333,1.865 1.75,1.281 true 2.083,4.365 1.667,3.948 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.583,0.135 2.042,0.333 0.458,0.198 10 false C36 1.25,2.219 1.708,2.417 0.458,0.198 10 false A48 0.094,2 0.406,2.156 0.313,0.156 10 false *b 2.417,1.76 2.875,1.958 0.458,0.198 10 false +B 2.146,4.25 2.604,4.448 0.458,0.198 10 false PSFT
*a Front view of wire harness connector
(to Shift Lever Position Sensor)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-7 (+B) - A48-1 (PSFT) Power switch off Below 1 Ω
C36-7 (+B) or A48-1 (PSFT) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the hybrid vehicle control ECU connector.


e.

Reconnect the shift lever position sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR