Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2018.05–2019.09
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292486 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A2A11  Drive Motor "A" Temperature Sensor Circuit Short to Ground  P0A2A15  Drive Motor "A" Temperature Sensor Circuit Short to Auxiliary Battery or Open  


DTC SUMMARY

MALFUNCTION DESCRIPTION


These DTCs are stored when the motor temperature sensor output is abnormal. The cause of this malfunction may be one of the following:

Hybrid vehicle control ECU internal malfunction
·

Hybrid vehicle control ECU malfunction


Motor temperature sensor malfunction
·

Internal motor temperature sensor malfunction

·

Open or short in motor temperature sensor


Wire harness between the motor temperature sensor and hybrid vehicle control ECU
·

The connectors are not connected properly

·

Foreign matter or water on the connector terminals

·

Open or short in wire harness


HINT:

If any of these DTCs are stored, the motor temperature sensor is malfunctioning and the self-protection function may not operate. Therefore under certain high load driving condition, the temperature of the motor (MG2) becomes high. If the self-protection function does not operate, the motor (MG2) may malfunction and cause the vehicle to enter fail-safe mode.



DESCRIPTION

The resistance of the thermistor built into the motor temperature sensor changes in accordance with changes in the motor (MG2) temperature. The lower the motor (MG2) temperature, the higher the thermistor resistance. Conversely, the higher the motor (MG2) temperature, the lower the resistance.

HINT:

The term "drive motor A" indicates the motor (MG2).


C189867E22
0.76,2.104 0.885,2.302 0.125,0.198 10 false 0 2,2.875 3.406,3.094 1.406,0.219 10 false Temperature (°C (°F)) 0.885,2.375 1.083,2.573 0.198,0.198 10 false 10 1.26,2.375 1.458,2.573 0.198,0.198 10 false 15 2.406,2.375 2.604,2.573 0.198,0.198 10 false 30 2.792,2.375 2.99,2.573 0.198,0.198 10 false 35 1.646,2.375 1.844,2.573 0.198,0.198 10 false 20 2.021,2.375 2.219,2.573 0.198,0.198 10 false 25 0.677,1.521 0.875,1.719 0.198,0.198 10 false 50 0.594,0.948 0.865,1.146 0.271,0.198 10 false 100 3.146,2.375 3.344,2.573 0.198,0.198 10 false 40 0.063,0.5 1.26,0.771 1.198,0.271 10 false Resistance (kΩ) 0.865,2.542 1.208,2.74 0.344,0.198 10 false (50) 1.229,2.552 1.573,2.75 0.344,0.198 10 false (59) 1.615,2.552 1.958,2.75 0.344,0.198 10 false (68) 1.979,2.563 2.323,2.76 0.344,0.198 10 false (77) 2.385,2.573 2.729,2.771 0.344,0.198 10 false (86) 2.771,2.583 3.115,2.781 0.344,0.198 10 false (95) 3.063,2.583 3.406,2.781 0.344,0.198 10 false (104)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A2A11 Drive Motor "A" Temperature Sensor Circuit Short to Ground Line short or short to ground in the motor temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Hybrid vehicle transaxle assembly (Motor temperature sensor)


Does not come on Master Warning:
Comes on
P0A2A15 Drive Motor "A" Temperature Sensor Circuit Short to Auxiliary Battery or Open Open or short to +B in the motor temperature sensor circuit
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Hybrid vehicle transaxle assembly (Motor temperature sensor)


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0A2A11 Motor Temperature
P0A2A15

HINT:

After confirming that DTC P0A2A11 or P0A2A15 is output, use the GTS to check "Motor Temperature" in the Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to ground


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A385273E68
4.969,2.844 6.979,3.396 2.01,0.552 10 false Hybrid Vehicle Control ECU 0.531,2.823 2.229,3.396 1.698,0.573 10 false Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly) 0.531,2.667 0.844,2.865 0.313,0.198 10 false C9 4.958,2.677 5.271,2.875 0.313,0.198 10 false A49 5.938,1.281 6.427,1.625 0.49,0.344 10 false ADC 4.865,1.917 5.417,2.219 0.552,0.302 10 false MMTG 4.854,1.167 5.333,1.458 0.479,0.292 10 false MMT 1.885,1.167 2.365,1.458 0.479,0.292 10 false MMT 1.792,1.906 2.344,2.208 0.552,0.302 10 false MMTG 4.604,1.167 4.948,1.49 0.344,0.323 10 false 24 4.604,1.917 4.948,2.24 0.344,0.323 10 false 23 2.313,1.146 2.656,1.469 0.344,0.323 10 false 1 2.302,1.917 2.646,2.24 0.344,0.323 10 false 2 3.677,1.167 4.021,1.49 0.344,0.323 10 false 17 3.042,1.167 3.385,1.49 0.344,0.323 10 false 17 3.677,1.906 4.021,2.229 0.344,0.323 10 false 18 3.052,1.917 3.396,2.24 0.344,0.323 10 false 18 2.615,2.635 4.729,3.188 2.115,0.552 10 false No. 1 Engine Room Relay Block 2.604,2.469 2.917,2.667 0.313,0.198 10 false CA4

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
a.

Check the connection condition of the Hybrid vehicle control ECU connectors and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

A394800C01
0.042,0.125 0.271,0.313 0.229,0.188 12 true *A 3.594,0.135 3.875,0.406 0.281,0.271 12 false *B
*A for LHD *B for RHD


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.


Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C




A

2.CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CONNECTOR CONNECTION CONDITION (INTERMEDIATE CONNECTOR)
a.

Check the connection condition of the motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

For vehicles in which the intermediate connector is inside the relay block, check for signs of water intrusion inside the relay block.


OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connectors.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)
a.
A376648

Check the connection condition of the motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.READ VALUE USING GTS (MOTOR TEMPERATURE)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (MOTOR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temperature.


d.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Motor Temperature
50003 397 66
Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Same as actual temperature C



e.

Turn the power switch off.



A

5.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

B

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)
a.
A376648

Disconnect the motor temperature sensor connector.


b.
A385118C07
0.25,1 0.75,1.25 0.5,0.25 1.885,1.792 1.917,1.333 true 2.427,1.792 2.115,1.323 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 2.354,1.833 2.781,2.063 0.427,0.229 10 false MMT 1.688,1.844 2.354,2.146 0.667,0.302 10 false MMTG 0.427,1.01 0.74,1.208 0.313,0.198 10 false C9
*a Component without harness connected
(Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C9-1 (MMT) - C9-2 (MMTG) Power switch off 0.343 to 1442 kΩ


HINT:

Terminal No. 3 on the component side connector is empty.



c.

Reconnect the motor temperature sensor connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HYBRID VEHICLE CONTROL ECU

NG

6.CHECK HYBRID VEHICLE CONTROL ECU
a.
A389500C02
0.552,0.833 1.052,1.083 0.5,0.25 0.5,2.5 0.729,1.854 true 1,2.5 0.781,1.854 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 0.313,2.542 0.875,2.698 0.563,0.156 10 false MMT 0.885,2.542 1.448,2.708 0.563,0.167 10 false MMTG 0.677,0.854 1.135,1.052 0.458,0.198 10 false A49
*a Component with harness connected
(to Hybrid Vehicle Control ECU)


Connect terminals 24 (MMT) and 23 (MMTG) of the A49 hybrid vehicle control ECU connector.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temperature.


e.

Read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Motor Temperature
50003 397 66
OK:
Tester Display Condition Specified Condition
Motor Temperature Terminals A49-24 (MMT) and A49-23 (MMTG) connected
Power switch on (IG)
215°C (419°F)



Result:
Proceed to
OK
NG


f.

Turn the power switch off.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)
a.
A376648

Disconnect the motor temperature sensor connector.


b.
A385118C07
0.25,1 0.75,1.25 0.5,0.25 1.885,1.792 1.917,1.333 true 2.427,1.792 2.115,1.323 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 2.354,1.833 2.781,2.063 0.427,0.229 10 false MMT 1.688,1.844 2.354,2.146 0.667,0.302 10 false MMTG 0.427,1.01 0.74,1.208 0.313,0.198 10 false C9
*a Component without harness connected
(Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C9-1 (MMT) - C9-2 (MMTG) Power switch off 0.343 to 1442 kΩ


HINT:

Terminal No. 3 on the component side connector is empty.



c.

Reconnect the motor temperature sensor connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (MOTOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)

NG

8.CHECK HARNESS AND CONNECTOR (MOTOR TEMPERATURE SENSOR - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the motor temperature sensor connector.


b.

Disconnect the hybrid vehicle control ECU connector.


c.
A496619C01
1.458,0.417 1.958,0.667 0.5,0.25 1.458,2.5 1.958,2.75 0.5,0.25 1.135,1.854 1.448,1.354 true 1.813,1.833 1.583,1.365 true 2.25,4.333 1.917,3.813 true 1.521,4.323 1.771,3.823 true 0.25,0.25 0.5,0.5 0.25,0.25 10 false *a 0.333,2.417 0.563,2.656 0.229,0.24 10 false *b 0.771,1.844 1.167,2.083 0.396,0.24 10 false MMT 1.854,1.844 2.333,2.083 0.479,0.24 10 false MMTG 1.021,4.333 1.5,4.583 0.479,0.25 10 false MMTG 2.271,4.344 2.667,4.583 0.396,0.24 10 false MMT 1.604,2.552 2.063,2.75 0.458,0.198 10 false A49 1.625,0.458 2.052,0.677 0.427,0.219 10 false C9
*a Front view of wire harness connector
(to Motor Temperature Sensor)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C9-1 (MMT) - A49-24 (MMT) Power switch off Below 1 Ω
C9-2 (MMTG) - A49-23 (MMTG) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C9-1 (MMT) or A49-24 (MMT) - Body ground and other terminals Power switch off 10 kΩ or higher
C9-2 (MMTG) or A49-23 (MMTG) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the hybrid vehicle control ECU.


e.

Reconnect the motor temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR