Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2018.05–2019.09
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292486 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A9B2A  Hybrid/EV Battery Temperature Sensor "A" Signal Stuck In Range  P0AC52A  Hybrid/EV Battery Temperature Sensor "B" Signal Stuck In Range  P0ACA2A  Hybrid/EV Battery Temperature Sensor "C" Signal Stuck In Range  P306562  Hybrid/EV Battery Temperature Sensor "A" Signal Compare Failure  


DESCRIPTION

Refer to the description for DTC P0A9B11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A9B11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A9B2A Hybrid/EV Battery Temperature Sensor "A" Signal Stuck In Range The performance of battery temperature sensor 0 is abnormal and its output is stuck.
(2 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0AC52A Hybrid/EV Battery Temperature Sensor "B" Signal Stuck In Range The performance of battery temperature sensor 1 is abnormal and its output is stuck.
(2 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor

·

Wire harness or connector


Comes on Master Warning:
Comes on
P0ACA2A Hybrid/EV Battery Temperature Sensor "C" Signal Stuck In Range The performance of battery temperature sensor 2 is abnormal and its output is stuck.
(2 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor

·

Wire harness or connector


Comes on Master Warning:
Comes on
P306562 Hybrid/EV Battery Temperature Sensor "A" Signal Compare Failure The performance of any battery temperature sensor is abnormal, and the difference in output between it and other battery temperature sensors is excessively large.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid battery thermistor

·

Wire harness or connector


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0A9B2A Hybrid Battery Temperature 1 to 3
P0AC52A
P0ACA2A
P306562

HINT:

If the vehicle as is left as is for 24 hours, the value of "Hybrid Battery Temperature" will be almost the same as the ambient temperature.


The following items can be helpful when performing repairs:

Data List
·

Vehicle Speed

·

Ambient Temperature


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


P0A9B2A, P0AC52A, P0ACA2A:

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position", "Hybrid Battery Temperature 1 to 3" and "Hybrid Battery Current" when ambient temperature is -10°C (14°F) or higher.

HINT:
·

Check that the output of each battery temperature sensor varies.

·

Check that the difference in output between each battery temperature sensor is not excessively large.



7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




P306562:

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 10 seconds or more when the ambient temperature is -10°C (14°F) or higher.

HINT:

Check that the difference in output between each battery temperature sensor is not excessively large.


7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A394809E01
2.5,3.219 2.083,3.052 true 2.5,2.25 2.083,2.083 true 2.5,4.177 2.083,4.01 true 2.5,5.167 2.083,5 true 1.542,5.771 3.073,5.969 1.531,0.198 10 false HV Battery 0.635,5.073 1.229,5.604 0.594,0.531 10 false Auxiliary Battery 0.427,3.417 1.958,3.615 1.531,0.198 10 false BATT-MAIN 0.427,2.219 1.396,2.438 0.969,0.219 10 false IGCT-IG 0.198,2.031 0.354,2.229 0.156,0.198 10 false 2 0.198,2.417 0.354,2.615 0.156,0.198 10 false 1 1.26,1.115 2.229,1.333 0.969,0.219 10 false IGCT 0.969,0.698 1.125,0.896 0.156,0.198 10 false 2 0.969,0.281 1.125,0.479 0.156,0.198 10 false 3 1.781,0.281 1.938,0.479 0.156,0.198 10 false 5 1.781,0.698 1.938,0.896 0.156,0.198 10 false 1 2.135,1.281 4.083,1.583 1.948,0.302 10 false Hybrid Vehicle Control ECU 2.667,0.792 3.635,1.01 0.969,0.219 10 false MREL 2.135,1.125 2.688,1.333 0.552,0.208 10 false A48 2.438,0.688 2.594,0.885 0.156,0.198 10 false 6 3.604,0.531 4.573,0.75 0.969,0.219 10 false IGCT NO. 2 4.167,0.281 4.323,0.479 0.156,0.198 10 false 2 3.74,0.281 3.896,0.479 0.156,0.198 10 false 1 4.719,0.354 5.198,0.552 0.479,0.198 10 false M41 4.719,5.833 5.198,6.031 0.479,0.198 10 false M41 4.729,1.896 5.104,2.115 0.375,0.219 10 false z12 4.729,2.406 5.115,2.604 0.385,0.198 10 false z12 4.729,2.865 5.177,3.094 0.448,0.229 10 false z12 4.729,3.375 5.135,3.583 0.406,0.208 10 false z12 4.729,3.823 5.156,4.01 0.427,0.188 10 false z12 4.729,4.333 5.229,4.531 0.5,0.198 10 false z12 4.729,4.813 5.125,5.031 0.396,0.219 10 false z12 4.729,5.323 5.167,5.521 0.438,0.198 10 false z12 4.802,0.167 4.958,0.365 0.156,0.198 10 false 1 4.802,1.698 4.958,1.896 0.156,0.198 10 false 1 4.802,2.208 5.125,2.406 0.323,0.198 10 false 7 4.802,2.646 5.156,2.885 0.354,0.24 10 false 4 4.771,3.167 5.135,3.396 0.365,0.229 10 false 10 4.802,3.615 5.156,3.813 0.354,0.198 10 false 3 4.802,4.125 5.156,4.302 0.354,0.177 10 false 9 4.802,4.615 5.156,4.813 0.354,0.198 10 false 2 4.802,5.125 5.125,5.313 0.323,0.188 10 false 8 4.802,5.635 5.177,5.844 0.375,0.208 10 false 5 5.135,1.813 5.479,2.031 0.344,0.219 10 false TC0 5.135,0.354 5.656,0.615 0.521,0.26 10 false IGCT 5.135,2.323 5.521,2.552 0.385,0.229 10 false GC0 5.135,2.781 5.542,3 0.406,0.219 10 false TB0 5.135,3.292 5.583,3.542 0.448,0.25 10 false GB0 5.135,3.74 5.5,3.99 0.365,0.25 10 false TB1 5.135,4.24 5.49,4.458 0.354,0.219 10 false GB1 5.135,4.729 5.531,4.99 0.396,0.26 10 false TB2 5.135,5.24 5.458,5.479 0.323,0.24 10 false GB2 5.135,5.833 5.594,6.042 0.458,0.208 10 false GND 5.104,6.344 6.844,6.635 1.74,0.292 10 false Battery Voltage Sensor 2.573,2.135 4.521,2.438 1.948,0.302 10 false Inlet Air Temperature Sensor 2.573,3.115 4.521,3.417 1.948,0.302 10 false Battery Temperature Sensor 0 2.573,4.073 4.521,4.375 1.948,0.302 10 false Battery Temperature Sensor 1 2.573,5.063 4.521,5.365 1.948,0.302 10 false Battery Temperature Sensor 2

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery



·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A371654C01
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.



·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.



·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
P0AFC00 or P0AFC96 is not output. A
P0AFC00 or P0AFC96 is also output. B


e.

Turn the power switch off.



A

2.CHECK INSTALLATION OF TEMPERATURE SENSOR (HYBRID BATTERY TEMPERATURE)

B

2.CHECK INSTALLATION OF TEMPERATURE SENSOR (HYBRID BATTERY TEMPERATURE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 hybrid battery cover sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


c.

Visually check the installation condition of the relevant battery temperature sensor.

A376409C03
5.552,1.99 5.802,2.198 0.25,0.208 10 true *1 3.646,1.667 3.906,1.896 0.26,0.229 10 true *2 1.615,1.656 1.844,1.885 0.229,0.229 10 true *3
*1 Battery Temperature Sensor 0 *2 Battery Temperature Sensor 1
*3 Battery Temperature Sensor 2 - -


Standard Condition:

Each battery temperature sensor is installed in the correct location with the correct orientation and its claws are engaged securely.



Result:
Result Proceed to
Each battery temperature sensor is installed in the correct location with the correct orientation and its claws are engaged securely. A
Claws are damaged. B
Any of battery temperature sensors are not installed correctly, but claws are not damaged. C


d.

Install the upper No. 1 hybrid battery cover sub-assembly.



A

3.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)

B

C

INSTALL PARTS CORRECTLY

3.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.

Disconnect the battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A368050C06
1.385,1.438 1.802,1.667 0.417,0.229 1.729,2.198 2.281,2.146 true 1.646,2.198 2.208,1.948 true 0.979,2.104 1.552,2.198 true 1.719,2.313 2.323,2.594 true 1.302,2.729 1.635,2.323 true 1.031,2.531 1.542,2.313 true 1.5,1.458 1.927,1.781 0.427,0.323 10 false z12 0.708,2 1.219,2.49 0.51,0.49 10 false TB0 2.24,1.833 2.75,2.323 0.51,0.49 10 false TB1 2.333,2.052 2.844,2.542 0.51,0.49 10 false TB2 2.365,2.563 2.875,3.052 0.51,0.49 10 false GB2 1.104,2.76 1.615,3.25 0.51,0.49 10 false GB1 0.719,2.521 1.229,3.01 0.51,0.49 10 false GB0 0.094,0.042 0.563,0.469 0.469,0.427 10 false *a
*a Rear view of wire harness connector
(to Battery Voltage Sensor)


Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 2).

Tester Connection:
Tester Connection Battery Temperature Sensor
z12-4 (TB0) - z12-10 (GB0) 0
z12-3 (TB1) - z12-9 (GB1) 1
z12-2 (TB2) - z12-8 (GB2) 2


Standard Resistance:
Thermistor Temperature Condition Specified Condition
0°C (32°F) Power switch off 26.7 to 27.8 kΩ
25°C (77°F) Power switch off 9.9 to 10.1 kΩ
40°C (104°F) Power switch off 5.73 to 5.92 kΩ


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



e.

Disconnect the battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



f.
A368048C08
0.813,2.094 1.219,2.333 0.406,0.24 2.813,2.083 3.219,2.323 0.406,0.24 1.823,2.198 2.01,1.677 true 1.729,2.198 1.813,1.646 true 1.635,2.177 1.615,1.542 true 1.552,2.198 1.396,1.594 true 1.917,2.792 1.813,2.333 true 1.813,3.167 1.729,2.323 true 1.521,3.01 1.646,2.313 true 1.146,3.073 1.552,2.313 true 2.594,2.208 2.781,1.688 true 2.906,3.01 2.594,2.302 true 2.042,1.531 2.5,1.729 0.458,0.198 10 false TC0 1.75,1.469 2.208,1.667 0.458,0.198 10 false TB2 1.5,1.375 1.958,1.573 0.458,0.198 10 false TB1 1.25,1.427 1.708,1.625 0.458,0.198 10 false TB0 1.865,2.875 2.323,3.073 0.458,0.198 10 false GC0 1.688,3.177 2.146,3.375 0.458,0.198 10 false GB2 1.406,3.063 1.865,3.271 0.458,0.208 10 false GB1 1,3.094 1.458,3.302 0.458,0.208 10 false GB0 2.802,1.552 3.292,1.875 0.49,0.323 10 false IGCT 2.833,3.052 3.292,3.25 0.458,0.198 10 false GND 0.927,2.104 1.302,2.458 0.375,0.354 10 false z12 2.896,2.115 3.271,2.469 0.375,0.354 10 false M41 0.115,0.021 0.573,0.219 0.458,0.198 10 false *a
*a Rear view of wire harness connector
(to Battery Voltage Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z12-4 (TB0) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-4 (TB0) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-10 (GB0) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-10 (GB0) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-3 (TB1) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-3 (TB1) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-9 (GB1) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-9 (GB1) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-2 (TB2) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-2 (TB2) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-8 (GB2) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-8 (GB2) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-1 (TC0) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-1 (TC0) - M41-5 (GND) Power switch off 10 kΩ or higher
z12-7 (GC0) - M41-1 (IGCT) Power switch off 10 kΩ or higher
z12-7 (GC0) - M41-5 (GND) Power switch off 10 kΩ or higher


NOTICE:

When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.



g.

Reconnect the battery voltage sensor connector.


h.

Install the No. 1 hybrid battery exhaust duct.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
4.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper No. 1 hybrid battery cover sub-assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY VOLTAGE SENSOR>REMOVAL


c.

Check the wire harness and connectors of the battery temperature sensor for abnormalities by sight and touch.

Specified Condition:

There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.



Result:
Proceed to
OK
NG


d.

Install the upper hybrid battery cover sub-assembly.



OK

NG

REPAIR HARNESS OR CONNECTOR (BATTERY TEMPERATURE SENSOR)