Refer to the description for DTC P310711.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P310711
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P310715 | Lost Communication with Airbag System Control Module Circuit Short to Auxiliary Battery or Open | Open or short to +B in the communication circuit
Communication from the airbag ECU assembly stopped and Circuit High has been detected for a certain period. (1 trip detection logic) |
·
Wire harness or connector ·
Airbag ECU assembly ·
Hybrid vehicle control ECU |
Does not come on | Master Warning:
Comes on |
| DTC No. | Data List |
|---|---|
| P310715 | Airbag Status (Collision) |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
With power switch on (IG) and wait for 15 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Refer to the wiring diagram for DTC P310711.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P310711
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| Airbag system DTCs are not output. | A |
| Airbag system DTCs are output. | B |
Turn the power switch off.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P310711
| Result | Proceed to |
|---|---|
| The waveform appears as shown in the illustration. | A |
| The waveform differs from the one shown in the illustration. | B |
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P06881F
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P310715 is not output. | A |
| P310715 is output again. | B |
Turn the power switch off.
A
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Airbag ECU Assembly) |
Check the connector connections and contact pressure of the relevant terminals for the F70 airbag ECU assembly connector.
The connectors are connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the hybrid vehicle control ECU connector.
Disconnect the airbag ECU assembly connector.
Turn the power switch on (IG).
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| *b | Rear view of wire harness connector
(to Airbag ECU Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F3-14 (ABFS) - Body ground | Power switch on (IG) | Below 1 V |
Turning the power switch on (IG) with the airbag sensor assembly connector and the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F3-14 (ABFS) - F70-14 (GSW2) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F3-14 (ABFS) or F70-14 (GSW2) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Reconnect the airbag ECU assembly connector.
Reconnect the hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F70 airbag ECU assembly connector.
Turn the power switch on (IG).
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
Measure the voltage according to the value(s) in the table below.
Turning the power switch on (IG) with the airbag ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F3-14 (ABFS) - Body ground | Power switch on (IG) | 11 to 14 V |
Turn the power switch off.
Reconnect the F70 airbag ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG