Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › 2019.09–2020.08
RM32K0E _58 Vehicle Interior _061818 DOOR LOCK _0304543 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
·

Door window regulator assembly

·

Door glass run


Initialize Power Window Control System
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:
·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal (for Audio and Visual System).

·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal (for Navigation System (for Radio and Display Type)).



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284C 3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

Hide 74232 4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

Hide 74231 5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

Hide 67602 6.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 68172A 7.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP

Hide 68195 8.REMOVE FRONT DOOR BELT SEAL

Hide 67832 9.REMOVE FRONT DOOR SERVICE HOLE COVER

Hide 68102 10.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Hide 67664 11.REMOVE DOOR FRAME UPPER GARNISH

Hide 68151C 12.REMOVE FRONT DOOR GLASS RUN

Hide 67404F 13.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Hide 69217D 14.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

Hide 69040A 15.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

a.
B450667C01
3.01,1.531 2.75,1.104 true 2.521,1.01 2.729,1.198 0.208,0.188 10 true *1
*1 Front Door Lock Open Rod
V113147

Remove in this Direction


Disconnect the connector.


b.

Using a T30 "TORX" socket wrench, remove the 3 screws.


c.

Disconnect the front door lock open rod as shown in the illustration.


d.

Remove the front door lock with motor assembly.


e.

When reusing the front door lock with motor assembly (w/o Double Locking System):

i.
B402282

Remove the door lock wiring harness seal from the front door lock with motor assembly.



f.

When reusing the front door lock with motor assembly (w/ Double Locking System):

i.
B458206

Remove the door lock wiring harness seal from the front door lock with motor assembly.



Hide 69035A 16.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY (w/o Double Locking System)

a.
B402283C02
0.646,1.5 0.469,1.802 true 0.365,1.802 0.677,1.958 0.313,0.156 10 false *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


b.
B402284

Disengage the guides to remove the front door lock cover sub-assembly from the front door lock with motor assembly.


Hide 69720B 17.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.

w/o Double Locking System:

i.
B402285

Disengage the guide to remove the front door lock remote control cable assembly from the front door lock with motor assembly.



b.

w/ Double Locking System:

i.
B450668

Disengage the guide to remove the front door lock remote control cable assembly from the front door lock with motor assembly.



Hide 69760C 18.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.

w/o Double Locking System:

i.
B402286

Disengage the guide to remove the front door inside locking cable assembly from the front door lock with motor assembly.



b.

w/ Double Locking System:

i.
B450669C01
1.875,0.521 1.417,0.396 true 1.177,0.302 1.406,0.521 0.229,0.219 10 true *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


ii.
B450670

Disengage the guide to remove the front door inside locking cable assembly from the front door lock with motor assembly.