Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › from 2019.09
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300402 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for the LHD vehicles.



PROCEDURE

Hide 55990B 1.INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY

a.
I112349

Engage the claws to install the lower defroster nozzle assembly.


Hide 2.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.


Hide 3.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:

Be sure to support the air conditioner unit assembly when installing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.


a.

Engage the guides to install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

I112547C01
0,0 0,0 false
V113147

Install in this Direction - -



b.
I112356

Connect 2 connectors.


c.

Engage the clamps.


d.

Install the 5 bolts.

I113811N01
1.052,3.844 1.208,4.042 0.156,0.198 10 true A 1.073,2.927 1.229,3.125 0.156,0.198 10 true A 6.74,1.448 6.896,1.646 0.156,0.198 10 true A 6.729,2.292 6.885,2.49 0.156,0.198 10 true A 1.042,2.417 1.198,2.615 0.156,0.198 10 true B

Torque:
Bolt A : 25 N*m (255 kgf*cm, 18 ft.*lbf)
Bolt B : 23.6 N*m (241 kgf*cm, 17 ft.*lbf)


e.

Temporarily install the nut.


f.

Install the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 88539J 4.CONNECT DRAIN COOLER HOSE

a.
I112352C01
1.656,3.083 1.24,2.896 true 1.688,3 1.948,3.208 0.26,0.208 10 true *1
*1 Cooler Unit Drain Hose Grommet


Connect the drain cooler hose.

NOTICE:

If the cooler unit drain hose grommet is disconnected from the vehicle body while connecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.



Hide 82141 5.INSTALL INSTRUMENT PANEL WIRE

a.

for LHD:

i.

Engage clamps and hook to connect the instrument panel wire.

I113759C02
3.292,4.354 4.083,5.115 4.083,5.115 3.885,4.354 true 2.323,4.063 2.625,3.604 2.625,3.604 2.51,4.323 true 0.833,4.938 1.094,5.146 true 0.49,5.177 0.75,5.385 true 5.51,0.979 5.625,0.51 5.625,0.51 6.219,0.635 true 4.021,0.438 4.385,0.479 true 3.135,0.76 3.271,0.563 true 3.031,1.083 3.875,1.365 3.875,1.365 3.656,1.052 true 1.885,1.219 1.583,1.365 true 0.719,0.865 0.521,1.063 true 2.615,4.646 2.729,4.948 true 5.531,3.354 5.688,3.625 true 6.25,2.573 6.74,3.01 6.74,3.01 6.49,3.104 true 4.073,5.135 4.333,5.354 0.26,0.219 10 true *a 6.813,2.969 7.073,3.188 0.26,0.219 10 true *a 5.708,3.667 5.969,3.885 0.26,0.219 10 true *a 2.583,3.406 2.844,3.625 0.26,0.219 10 true *a 2.677,4.99 2.938,5.208 0.26,0.219 10 true *a 1.031,5.167 1.292,5.385 0.26,0.219 10 true *a 1.344,1.292 1.563,1.49 0.219,0.198 10 true *a 0.729,0.719 0.99,0.938 0.26,0.219 10 true *a 3.302,0.417 3.563,0.635 0.26,0.219 10 true *a 3.74,0.313 4,0.531 0.26,0.219 10 true *a 3.979,1.25 4.24,1.469 0.26,0.219 10 true *a 5.438,0.302 5.698,0.521 0.26,0.219 10 true *a 0.281,5.01 0.542,5.229 0.26,0.219 10 true *b 6.083,0.708 6.24,0.906 0.156,0.198 10 true A 1.594,0.531 1.75,0.729 0.156,0.198 10 true A 1.521,0.74 1.677,0.938 0.156,0.198 10 true A 6.792,3.604 6.948,3.802 0.156,0.198 10 true B
*a Clamp *b Hook



ii.

Install the instrument panel junction block assembly with main body ECU with the bolt and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iii.

Install the 4 ground wires with the 4 bolts.

Torque:
Bolt A : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)
Bolt B (Part No. 90119-06995) : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)
Bolt B (Part No. 90119-W0017) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


iv.

Install the bolt and screw.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


v.

Connect each connector.



b.

for RHD:

i.

Engage clamps and hook to connect the instrument panel wire.

I113760C02
3.417,5.25 2.677,4.583 true 3.281,4.406 3.979,4.865 3.979,4.865 3.917,4.406 true 6.542,5.031 6.729,4.646 6.729,4.646 6.573,4.375 true 2.896,5.313 3.417,5.25 3.417,5.25 2.542,3.99 true 6.302,5.49 5.906,5.375 true 1.01,4.802 0.781,4.906 true 0.917,5.552 0.719,5.469 true 1.521,0.438 1.271,0.5 true 1.073,1.229 0.813,1 true 3.396,1.052 3.917,1.25 3.917,1.25 4.198,0.979 true 2.708,1.135 2.938,1.313 true 6.396,0.906 6.625,1.083 true 0.552,2.719 1.052,3 1.052,3 0.979,2.406 true 6.781,4.552 6.99,4.76 0.208,0.208 10 true *a 5.708,5.281 5.917,5.49 0.208,0.208 10 true *a 3.479,5.208 3.688,5.417 0.208,0.208 10 true *a 3.917,4.906 4.125,5.115 0.208,0.208 10 true *a 1.021,4.688 1.229,4.896 0.208,0.208 10 true *a 1.021,1.188 1.229,1.396 0.208,0.208 10 true *a 1.063,0.427 1.271,0.635 0.208,0.208 10 true *a 2.938,1.26 3.146,1.469 0.208,0.208 10 true *a 3.823,1.26 4.031,1.469 0.208,0.208 10 true *a 6.219,0.75 6.427,0.958 0.208,0.208 10 true *a 0.938,5.51 1.146,5.719 0.208,0.208 10 true *b 1.01,3.031 1.219,3.24 0.208,0.208 10 true *a 5.708,4.094 5.896,4.292 0.188,0.198 10 true A 5.688,4.365 5.844,4.542 0.156,0.177 10 true A 6.802,5.25 6.958,5.427 0.156,0.177 10 true B 5.677,0.698 5.833,0.875 0.156,0.177 10 true C 5.635,0.344 5.792,0.521 0.156,0.177 10 true C 1.906,0.469 2.063,0.646 0.156,0.177 10 true C
*a Clamp *b Hook



ii.

Install the instrument panel junction block assembly with main body ECU with the bolt and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iii.

Install the 2 nuts A.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


iv.

Install the 4 ground wires with the 4 bolts.

Torque:
Bolt B (Part No. 90119-06995) : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)
Bolt B (Part No. 90119-W0017) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Bolt C : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)


v.

Install the bolt and screw.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


vi.

Connect each connector.



Hide 55308B 6.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
I112348

Install the No. 3 instrument panel to cowl brace sub-assembly with the nut and bolt.

Torque:
Bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Engage the claws and clamps.


Hide 55307C 7.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

for LHD:

i.
I112542

Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


ii.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



iii.

Install the ground wire with the bolt.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


iv.

Engage the clamps to connect the wire harness.



b.

for RHD:

i.

Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


ii.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



iii.
I113736

Install the ground wire with the bolt.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


iv.

Engage the clamps to connect the wire harness.



Hide 55306A 8.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

for LHD:

i.

Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


ii.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



iii.
I113757

Engage the clamps to connect the wire harness.



b.

for RHD:

i.

Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


ii.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



iii.
I113738

Engage the clamps to connect the wire harness.



c.

w/ PTC Heater:

i.

Install the bolt to connect the ground wire.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)



d.

Install the relay block assembly with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 9.INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

for LHD:

i.

Tighten the 3 bolts, 2 screws and nut in the order shown in the illustration to install the air conditioner unit.

I112549E01
1.885,0.938 2.042,1.135 0.156,0.198 10 true 1 4.323,0.969 4.479,1.167 0.156,0.198 10 true 3 6.156,0.948 6.313,1.146 0.156,0.198 10 true 2 2.115,4.365 2.271,4.563 0.156,0.198 10 true 4 3.906,4.438 4.063,4.635 0.156,0.198 10 true 5 5.656,4.417 5.813,4.615 0.156,0.198 10 true 6

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



b.

for RHD:

i.

Tighten the 3 bolts, 2 screws and nut in the order shown in the illustration to install the air conditioner unit.

I112550E01
1.896,0.927 2.052,1.125 0.156,0.198 10 true 2 4.208,0.917 4.365,1.115 0.156,0.198 10 true 1 6.115,0.896 6.271,1.094 0.156,0.198 10 true 3 1.99,4.406 2.146,4.604 0.156,0.198 10 true 6 5.594,4.385 5.75,4.583 0.156,0.198 10 true 4

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 87212 10.INSTALL REAR NO. 1 AIR DUCT (w/ Rear Air Duct)

a.
I112806C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear No. 1 air duct.


Hide 87212F 11.INSTALL REAR NO. 2 AIR DUCT (w/ Rear Air Duct)

a.
I112519C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear No. 2 air duct as shown in the illustration.


Hide 87212G 12.INSTALL REAR NO. 3 AIR DUCT (w/ Rear Air Duct)

a.
I112515C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear No. 3 air duct as shown in the illustration.


Hide 87212H 13.INSTALL REAR NO. 4 AIR DUCT (w/ Rear Air Duct)

a.
I112514C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear No. 4 air duct as shown in the illustration.


b.
I112513C01
0,0 0,0 false
V113147

Install in this Direction


Install the front floor carpet assembly to its original position as shown in the illustration.


c.

Engage the clamps.


d.

Install the clip.


e.

Install the 2 front floor carpet clips.


Hide 87212J 14.INSTALL REAR NO. 5 AIR DUCT (w/ Rear Air Duct)

a.
I112518C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear No. 5 air duct as shown in the illustration.


Hide 87212K 15.INSTALL REAR NO. 6 AIR DUCT (w/ Rear Air Duct)

a.
I112517C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear No. 6 air duct as shown in the illustration.


Hide 55215D 16.INSTALL NO. 3 DASH PANEL INSULATOR PAD

a.
I112343

Engage the clips to install the No. 3 dash panel insulator pad.


b.
I112516C01
0,0 0,0 false
V113147

Install in this Direction


Install the front floor carpet assembly to its original position as shown in the illustration.


c.

Engage the clamps.


d.

Install the clip.


e.

Install the 2 front floor carpet clips.


Hide 88625Q 17.INSTALL COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)

a.

Connect the aspirator and connector to install the cooler thermistor (room temperature sensor).


Hide 82877 18.INSTALL ECU INTEGRATION BOX RH (for LHD)

Hide 82878 19.INSTALL ECU INTEGRATION BOX LH (for RHD)

Hide 89340A 20.INSTALL CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar System)

Hide 85940 21.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY

Hide 22.INSTALL STEERING COLUMN ASSEMBLY

Hide 55401E 23.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 24.INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)

Hide 25.INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)

HINT:

Use the same procedure as for the LH side.


Hide 26.INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)

Hide 27.INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)

HINT:

Use the same procedure as for the LH side.


Hide 88716A 28.CONNECT COOLER REFRIGERANT LIQUID PIPE A

a.

Remove the vinyl tape from the cooler refrigerant liquid pipe A.


b.

Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler refrigerant liquid pipe A.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the cooler refrigerant liquid pipe A.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the cooler refrigerant liquid pipe A.


Hide 88707 29.CONNECT SUCTION PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Apply sufficient compressor oil to a new O-ring and fitting surface of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction pipe sub-assembly.


e.
I112493

Rotate the hook connector as shown in the illustration.


f.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87245 30.CONNECT INLET HEATER WATER HOSE

a.
I112494C01
1.656,2.927 1.177,2.792 true 0.156,2.313 0.469,2.51 0.313,0.198 10 false *a 0.969,2.677 1.281,2.875 0.313,0.198 10 false *b 2.229,2.51 2.542,2.708 0.313,0.198 10 false *c 1.125,1.26 1.313,1.469 0.188,0.208 10 true A
*a View A
*b Marking
*c Clip Installation Angle (120°)


Connect the inlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.

Paint Mark:
Producing Area Color
for TMMT Made White
for TMC Made Brown


NOTICE:

Do not apply excessive force to the inlet heater water hose.



Hide 87246 31.CONNECT OUTLET HEATER WATER HOSE

a.
I112495C01
1.771,2.927 2.219,2.854 true 0.156,2.25 0.469,2.448 0.313,0.198 10 false *a 1.021,2.417 1.333,2.615 0.313,0.198 10 false *c 2.281,2.698 2.594,2.896 0.313,0.198 10 false *b 0.938,0.938 1.115,1.135 0.177,0.198 10 true A
*a View A
*b Marking
*c Clip Installation Angle (120°)


Connect the outlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.

Paint Mark:
Producing Area Color
for TMMT Made White
for TMC Made Red


NOTICE:

Do not apply excessive force to the outlet heater water hose.



Hide 55701J 32.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 33.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55735C 34.INSTALL COWL BODY MOUNTING REINFORCEMENT RH

Hide 55736D 35.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55734D 36.INSTALL WATER GUARD PLATE LH (for TMC Made)

Hide 55737B 37.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 38.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 41. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT