Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door) › 2019.09–2020.08
RM32K0E _59 Vehicle Exterior _061311 WINDOW / GLASS _0302413 POWER WINDOW REGULATOR MOTOR(for Rear Door) A

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the power window regulator motor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
·

Door window regulator assembly

·

Power window regulator motor assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

NOTICE:
·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal (for Audio and Visual System).

·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal (for Navigation System (for Radio and Display Type)).



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284D 2.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Hide 84810D 3.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

Hide 67498 4.REMOVE REAR DOOR REAR FRAME BRACKET

Hide 67604 5.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 67498 6.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP

Hide 68197 7.REMOVE REAR DOOR BELT SEAL

Hide 68199 8.REMOVE REAR DOOR BELT REAR SEAL

Hide 67842E 9.REMOVE REAR DOOR SERVICE HOLE COVER

Hide 67674A 10.REMOVE REAR DOOR FRAME GARNISH

Hide 68152C 11.REMOVE REAR DOOR GLASS RUN

Hide 67408F 12.REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY

Hide 68104 13.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Hide 14.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

Hide 15.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B454701

Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.