Home › Engine / Hybrid System › M20A-FXS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › from 2019.09
RM32K0E _51 Engine / Hybrid System _083957 M20A-FXS INTAKE / EXHAUST _0404363 EXHAUST MANIFOLD A

M20A-FXS INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 58166 2.REMOVE FRONT FLOOR COVER LH

a.
A393190C02
0,0 0,0 false
V100135

Bolt
V100136

Clip


Remove the 2 bolts and clip and disengage the 5 clamps to remove the front floor cover LH from the vehicle body.


Hide 58165B 3.REMOVE FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.


Hide 57533B 4.REMOVE FRONT FLOOR CENTER BRACE

a.
A439994

Remove the 12 bolts and 3 front floor center braces from the vehicle body.


Hide 17410 5.REMOVE FRONT EXHAUST PIPE ASSEMBLY

CAUTION:
·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



a.
A439818

Disconnect the No. 2 air fuel ratio sensor connector.


b.

Disengage the clamp.


c.
A450896

Remove the 4 bolts and 4 compression springs and disconnect the front exhaust pipe assembly from the exhaust manifold and tail exhaust pipe assembly.


d.

Remove the front exhaust pipe assembly from the 2 exhaust pipe supports.


e.

Remove the 2 exhaust pipe gaskets from the exhaust manifold and front exhaust pipe assembly.


Hide 7.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A432894

Remove the bolt and wire harness clamp bracket.


Hide 58151 8.REMOVE NO. 1 FRONT FLOOR HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A439821

Remove the 3 nuts and No. 1 front floor heat insulator from the vehicle body.


Hide 25733A 9.SEPARATE NO. 1 VACUUM PIPE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A432849

Remove the nut.


b.

Using a 14 mm union nut wrench, separate the No. 1 vacuum pipe from the exhaust manifold.


Hide 17167 10.SEPARATE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440593

Remove the 3 bolts and separate the No. 1 exhaust manifold heat insulator from the exhaust manifold.


Hide 17118 11.REMOVE MANIFOLD STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A426174

Remove the bolt, nut and manifold stay from the exhaust manifold and cylinder block sub-assembly.


Hide 17141 12.REMOVE EXHAUST MANIFOLD

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440594

Using a 12 mm deep socket wrench, remove the 7 nuts and separate the exhaust manifold from the cylinder head sub-assembly.


b.

Remove the No. 1 exhaust manifold heat insulator and exhaust manifold.


c.
A432899

Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.


Hide 17168 13.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A426178

Remove the 3 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold.