The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.
| *a | Heavy object exceeding the capacity of the engine lifter |
Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.
If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.
| *a | High temperature areas |
Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.
Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
3. DISCHARGE FUEL SYSTEM PRESSURE
4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
5.REMOVE FRONT WHEELS
51410
6.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
Remove the 4 bolts, 4 screws, 4 clips and No. 1 engine under cover assembly from the vehicle.
51444A
7.REMOVE REAR ENGINE UNDER COVER LH
Remove the 6 clips and rear engine under cover LH from the vehicle.
51443C
8.REMOVE REAR ENGINE UNDER COVER RH
Remove the 6 clips and rear engine under cover RH from the vehicle.
9.DRAIN ENGINE OIL
10.DRAIN ENGINE COOLANT (for Engine)
11.DRAIN HYBRID TRANSAXLE FLUID
53141F
12.REMOVE RADIATOR COVER
17751
13.REMOVE NO. 1 AIR CLEANER INLET
Remove the 4 bolts and No. 1 air cleaner inlet from the upper radiator support sub-assembly and air cleaner case sub-assembly.
14.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
17801
15.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17701
16.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Remove the 3 bolts and remove the air cleaner case sub-assembly.
89661
17.REMOVE ECM
82662A
18.REMOVE NO. 1 RELAY BLOCK COVER
Disengage the claw and 2 guides to remove the No. 1 relay block cover from the engine room relay block.
19.REMOVE ENGINE WIRE
Disconnect the 3 connectors from the engine room relay block.
Disengage the 2 claws to separate the engine wire from the engine room relay block.
Remove the nut.
Disengage the 2 claws to separate the engine wire from the engine room relay block.
Remove the 2 bolts to separate the engine wire from the vehicle.
Disengage the 3 clamps to separate the engine wire from the vehicle.
G9200
20.REMOVE INVERTER WITH CONVERTER ASSEMBLY
G92A0A
21.REMOVE INVERTER RESERVE TANK ASSEMBLY
Remove the 2 bolts.
Slide the clip and disconnect the No. 1 inverter cooling hose assembly from the inverter reserve tank assembly.
Slide the clip and disconnect the inlet hybrid water pump hose from the inverter reserve tank assembly.
33820B
22.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.
Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.
16571C
23.DISCONNECT NO. 1 RADIATOR HOSE
Disengage the clamp to separate the No. 1 radiator hose.
Slide the clip and disconnect the No. 1 radiator hose from the water outlet.
16572D
24.DISCONNECT NO. 2 RADIATOR HOSE
Disengage the 3 clamps to disconnect the No. 1 inverter cooling hose assembly and inlet hybrid water pump hose from the fan shroud assembly.
Slide the clip and disconnect the No. 2 radiator hose from the water inlet sub-assembly.
G922H
25.DISCONNECT INLET HYBRID RADIATOR HOSE
Slide the clip and disconnect the inlet hybrid radiator hose from the motor cooling cooler.
G922F
26.DISCONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE
Slide the clip and disconnect the outlet No. 1 hybrid water pump hose from the motor cooling cooler.
23829A
27.REMOVE NO. 1 FUEL VAPOR FEED HOSE
| *a | Retainer |
|
Pinch |
|
Pull off |
Pinch the retainer of the No. 1 fuel vapor feed hose connector, and then pull the No. 1 fuel vapor feed hose connector off of the No. 2 fuel vapor feed pipe.
Be sure to disconnect the No. 1 fuel vapor feed hose connector by hand.
25860
28.REMOVE PURGE VALVE (PURGE VSV)
23818
29.REMOVE FUEL VAPOR FEED PIPE
Disengage the clamp and remove the bolt to separate the engine wire.
Disengage the clamp to separate the No. 1 fuel vapor feed hose.
Remove the bolt and fuel vapor feed pipe from the fuel delivery guard.
23825
30.REMOVE FUEL DELIVERY GUARD
Remove the bolt and fuel delivery guard from the engine mounting bracket RH.
87245
31.DISCONNECT INLET HEATER WATER HOSE
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to disengage the lock claws and pull off the inlet heater water hose.
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected water hose sub-assembly and inlet heater water hose connector with plastic bags to prevent damage and contamination.
87246
32.DISCONNECT OUTLET HEATER WATER HOSE
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to disengage the lock claws and pull off the outlet heater water hose.
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected water hose sub-assembly and outlet heater water hose connector with plastic bags to prevent damage and contamination.
23901
33.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Disengage the clamp to separate the fuel tube sub-assembly.
Disconnect the fuel tube sub-assembly from the fuel pump assembly.
Click hereEngine / Hybrid System>M20A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
16283B
34.DISCONNECT WATER BY-PASS HOSE
Slide the hose clip and disconnect the water by-pass hose from the No. 3 water by-pass pipe.
16267
35.SEPARATE NO. 3 WATER BY-PASS HOSE
Disengage the clamp to separate the No. 3 water by-pass hose.
88703
36.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY
88704
37.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
38. SECURE STEERING WHEEL ASSEMBLY
45259A
39.REMOVE COLUMN HOLE COVER SILENCER SHEET
45260
40.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45025D
41.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
17410
42.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
43.REMOVE DRIVE SHAFT ASSEMBLY
51108A
44.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
51107A
45.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
46.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
Remove the 3 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.
Remove the bolt and No. 2 engine mounting stay LH.
Remove the 6 bolts to separate the front suspension crossmember sub-assembly from the vehicle.
Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
89481B
47.REMOVE DIFFERENTIAL PRESSURE SENSOR
48.REMOVE EMISSION CONTROL VALVE BRACKET
Remove the bolt and emission control valve bracket from the cylinder head sub-assembly.
49.INSTALL ENGINE HANGER
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
|
Bolt |
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-25030 |
| No. 2 Engine Hanger | 12282-25010 |
| Bolt | 91552-F1040 |
Attach an engine sling device and hang the engine assembly with transaxle with a chain block.
Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.
Do not perform any procedure while the engine assembly with transaxle is suspended because doing so may cause the engine assembly with transaxle to drop, resulting in injury. However, the engine assembly with transaxle needs to be suspended when it is installed to or removed from an engine stand.
12372A
50.REMOVE ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Remove the 4 bolts, nut and engine mounting insulator LH from the vehicle.
12305
51.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Remove the 2 bolts and No. 2 earth wire from the engine mounting insulator sub-assembly RH and vehicle.
Remove the bolt, nut and disconnect the air conditioner tube and accessory assembly.
Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle.
28193
52.REMOVE STARTER HOLE INSULATOR
11363A
53.REMOVE FLYWHEEL HOUSING SIDE COVER
Remove the flywheel housing side cover from the cylinder block sub-assembly.
23819
54.REMOVE NO. 2 FUEL VAPOR FEED PIPE
Remove the bolt, nut and No. 2 fuel vapor feed pipe from the fuel hose brackets.
821H2
55.REMOVE HV AIR CONDITIONING WIRE
82121
56.REMOVE ENGINE WIRE
Remove the 3 bolts.
Remove the bolt.
Remove the 3 bolts.
Remove the bolt.
Disconnect all the clamps and connectors and remove the engine wire from the engine assembly with transaxle.
57.REMOVE ENGINE ASSEMBLY
88370
58.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY
31270
59.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY
13405
60.REMOVE FLYWHEEL SUB-ASSEMBLY
19315
61.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
62.INSTALL ENGINE TO ENGINE STAND
Install the engine assembly to an engine stand.
63.REMOVE ENGINE HANGER
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.