The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during battery voltage sensor removal/installation are shown below.
This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.
If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.
Be sure to wear insulating gloves when working on high voltage wiring or components.
If work is performed without wearing insulating gloves, there is a danger of electric shock.
The type of battery voltage sensor to be used varies depending on the vehicle model.
| *a | Black Label |
The type of battery voltage sensor can be confirmed by the color of the label.
If the wrong type of battery voltage sensor is installed, the power switch cannot be turned on (READY).
After installing the battery voltage sensor, perform the following to check that the power switch can be turned on (READY).
Turn the power switch on (READY).
Turn the power switch off and wait for 30 seconds or more.
Turn the power switch on (READY) again.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
G3834
2.REMOVE SERVICE PLUG GRIP
3.DISCONNECT ENGINE WIRE
4.REMOVE CONNECTOR COVER ASSEMBLY
5.CHECK TERMINAL VOLTAGE
6.INSTALL CONNECTOR COVER ASSEMBLY
7.CONNECT ENGINE WIRE
8.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY
72693
9.REMOVE REAR SEAT CUSHION LOCK HOOK
67918A
10.REMOVE REAR DOOR SCUFF PLATE LH
76974F
11.REMOVE REAR UNDER SIDE COVER LH
67917A
12.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
76973F
13.REMOVE REAR UNDER SIDE COVER RH
Use the same procedure as for the LH side.
76971G
14.REMOVE REAR UNDER COVER
71033
15.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY
G9230
16.REMOVE BATTERY COOLING BLOWER ASSEMBLY
G92N4A
17.REMOVE NO. 1 HV BATTERY COVER PANEL RH
821H1
18.DISCONNECT HV FLOOR UNDER WIRE
82161
19.DISCONNECT FLOOR WIRE
G92F1
20.REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT
82161
21.DISCONNECT FLOOR WIRE
G920L
22.REMOVE UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY
Be sure to wear insulated gloves and protective goggles.
Remove the 5 bolts.
Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.
To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.
If the HV battery has been struck or dropped, replace it.
Move the HV battery toward the front of the vehicle.
| *a | Bolt |
| *b | Nut |
Remove the 6 bolts, 5 nuts and upper No. 1 hybrid battery cover sub-assembly from the HV battery.
G92Q1
23.REMOVE NO. 1 HV BATTERY SHIELD PANEL
Be sure to wear insulated gloves and protective goggles.
Disengage the clamp.
Disconnect the battery voltage sensor connector.
Remove the bolt and 2 nuts.
| *1 | No. 1 HV Battery Shield Panel |
| *2 | No. 2 Hybrid Battery Shield Sub-assembly |
|
Pull Back |
Pull back the No. 2 hybrid battery shield sub-assembly and remove the No. 1 HV battery shield panel from the HV battery.
Pull back the No. 2 hybrid battery shield sub-assembly until it is separated from the 2 stud bolts of the No. 1 HV battery shield panel.
89892A
24.REMOVE BATTERY VOLTAGE SENSOR
Be sure to wear insulated gloves and protective goggles.
Disconnect the battery voltage sensor connector.
Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.
Remove the bolt and battery voltage sensor from the HV battery.
If the battery voltage sensor has been struck or dropped, replace it.