Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2019.09–2020.08
RM32K0E _58 Vehicle Interior _062036 INTERIOR PANELS / TRIM _0302277 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof headlining removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

CAUTION:
B458500

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the power switch off, the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)

Hide 2.REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)

Hide 3.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 4.REMOVE REAR SEAT ASSEMBLY

Hide 64330D 5.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

a.
B461491

Disengage the hooks.


b.
B557958C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guides to remove the package tray trim panel assembly as shown in the illustration.


Hide 64910J 6.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

a.
B461529

Disengage the hooks.


b.
B461527C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guides to remove the tonneau cover assembly as shown in the illustration.


Hide 58410B 7.REMOVE DECK BOARD ASSEMBLY

a.
B459311C01
0,0 0,0 false
V100155

Hook and Loop Fastener
V113147

Remove in this Direction


for Type A:

i.

Disengage the hook and loop fastener.


ii.

Remove the deck board assembly as shown in the illustration.



b.
B459313C01
0,0 0,0 false
V113147

Remove in this Direction


for Type B:

i.

Remove the deck board assembly as shown in the illustration.



c.
B459315C01
0,0 0,0 false
V113147

Remove in this Direction


for Type C:

i.

Remove the deck board assembly as shown in the illustration.



d.
B459317C01
0,0 0,0 false
V113147

Remove in this Direction


for Type D:

i.

Remove the deck board assembly as shown in the illustration.



Hide 64777J 8.REMOVE SPARE WHEEL CUSHION (for 2ZR-FXE)

a.
B459319C01
0,0 0,0 false
V113147

Remove in this Direction


for Type A:

i.

Remove the spare wheel cushion as shown in the illustration.



b.
B459321C01
0,0 0,0 false
V113147

Remove in this Direction


for Type B:

i.

Remove the spare wheel cushion as shown in the illustration.



c.
B459323C01
0,0 0,0 false
V113147

Remove in this Direction


for Type C:

i.

Remove the spare wheel cushion as shown in the illustration.



d.
B459325C01
0,0 0,0 false
V113147

Remove in this Direction


for Type D:

i.

Remove the clip.


ii.

Remove the spare wheel cushion as shown in the illustration.



Hide 64997 9.REMOVE DECK FLOOR BOX LH (w/ Deck Floor Box)

a.
B459333C01
0,0 0,0 false
V113147

Remove in this Direction


for Type A:

i.

Disengage the guide to remove the deck floor box LH as shown in the illustration.



b.
B459335C01
0,0 0,0 false
V113147

Remove in this Direction


for Type B:

i.

Disengage the guide to remove the deck floor box LH as shown in the illustration.



Hide 64995 10.REMOVE DECK FLOOR BOX RH (w/ Deck Floor Box)

a.
B459327C01
0,0 0,0 false
V113147

Remove in this Direction


for Type A:

i.

Disengage the guide to remove the deck floor box RH as shown in the illustration.



b.
B459329C01
0,0 0,0 false
V113147

Remove in this Direction


for Type B:

i.

Disengage the guide to remove the deck floor box RH as shown in the illustration.



c.
B557949C02
0,0 0,0 false
V113147

Remove in this Direction


for Type C:

i.

Disengage the guides to remove the deck floor box RH as shown in the illustration.



Hide 64429B 11.REMOVE LUGGAGE ROOM BOX (for M20A-FXS with Spare Tire)

a.
B557951C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guides to remove the luggage room box as shown in the illustration.


Hide 12.REMOVE SPARE TIRE (for M20A-FXS with Spare Tire)

Hide 58440 13.REMOVE BATTERY SERVICE HOLE COVER ASSEMBLY (for M20A-FXS without Spare Tire)

Hide 64991 14.REMOVE DECK FLOOR FRONT BOX (for M20A-FXS without Spare Tire)

a.
B557953C02
0,0 0,0 false
V113147

Remove in this Direction


Remove the deck floor front box as shown in the illustration.


Hide 67914 15.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67913 16.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62112 17.REMOVE COWL SIDE TRIM BOARD LH

Hide 62111C 18.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 62312B 19.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 20.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62212 21.REMOVE FRONT PILLAR GARNISH LH

Hide 62211 22.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 67918A 23.REMOVE REAR DOOR SCUFF PLATE LH

a.
B461399C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Disengage the claws and guides to remove the rear door scuff plate LH as shown in the illustration.


Hide 67917A 24.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 76974F 25.REMOVE REAR UNDER SIDE COVER LH

a.
B461397C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 clips.


b.

Disengage the clips, claw and guide to remove the rear under side cover LH as shown in the illustration.


Hide 76973F 26.REMOVE REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 62332A 27.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62331A 28.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 71304C 29.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH

a.
B459341

Loosen the bolt to remove the rear seatback hinge sub-assembly LH.


Hide 71303C 30.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62552F 31.REMOVE REAR SEAT SIDE GARNISH LH

a.
B459342C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Disengage the clip, claws and guide to remove the rear seat side garnish LH as shown in the illustration.


Hide 62551F 32.REMOVE REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 33.REMOVE LAP BELT OUTER ANCHOR COVER

Hide 73220 34.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 73210 35.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62414A 36.REMOVE CENTER PILLAR LOWER GARNISH LH

a.
B459344C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Disengage the clips and claws to remove the center pillar lower garnish LH as shown in the illustration.


Hide 62413A 37.REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62420A 38.REMOVE CENTER PILLAR GARNISH ASSEMBLY LH

a.
B459346C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the 2 clips.


b.

Disengage the clip and guides to remove the center pillar garnish assembly LH as shown in the illustration.


c.

When reusing the center pillar garnish assembly LH:

i.

Remove the clip from the center pillar garnish assembly LH.



Hide 62410A 39.REMOVE CENTER PILLAR GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 64716D 40.REMOVE DECK TRIM REAR COVER

a.
B459348

w/ Hook:

i.

Remove the 2 bolts and 2 luggage hold belt strikers.



b.
B459349

w/o Hook:

i.

Remove the 2 clips.



c.
B459350C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Disengage the clips, claws and guides to remove the deck trim rear cover as shown in the illustration.


Hide 81330 41.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Hide 64715C 42.REMOVE DECK TRIM SIDE COVER LH (w/ Cover)

a.
B459352

Turn the cover knob as shown in the illustration and unlock it.


b.
B459354C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the guides to remove the deck trim side cover LH as shown in the illustration.


Hide 64714C 43.REMOVE DECK TRIM SIDE COVER RH (w/ Cover)

HINT:

Use the same procedure as for the LH side.


Hide 64740C 44.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

a.
B461344

w/ Hook:

i.

Remove the bolt and luggage hold belt striker.



b.
B461345

w/o Hook:

i.

Remove the clip.



c.
B461346C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips and claws to remove the deck trim side panel assembly LH as shown in the illustration.


d.

Disconnect the rear seat 3 point type outer belt assembly LH.


Hide 64730B 45.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62480A 46.REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH

a.
B461348C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the clips and guide to remove the roof side inner garnish assembly LH as shown in the illustration.


b.

When reusing the roof side inner garnish assembly LH:

i.

Remove the 5 clips from the roof side inner garnish assembly LH.



Hide 62470A 47.REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 89943 48.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

Hide 86466E 49.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Lane Departure Alert System)

Hide 86466D 50.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Lane Departure Alert System)

Hide 87834 51.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Cover)

Hide 81340 52.REMOVE VANITY LIGHT ASSEMBLY (w/ Vanity Light)

Hide 81260A 53.REMOVE MAP LIGHT ASSEMBLY (for TMMT Made)

Hide 81260A 54.REMOVE MAP LIGHT ASSEMBLY (for TMC Made)

Hide 81240 55.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 89732A 56.REMOVE THEFT WARNING ULTRASONIC SENSOR (w/ Intrusion Sensor)

Hide 57.REMOVE COMMUNICATION TELEMATICS BOX ASSEMBLY (w/ Telematics Transceiver)

Hide 74325 58.REMOVE VISOR BRACKET COVER

HINT:

Use the same procedures for the opposite side.


a.
B461350C01
0,0 0,0 false
V113147

Remove in this Direction


Using a molding remover A, disengage the claws to remove the visor bracket cover as shown in the illustration.


Hide 74320 59.REMOVE VISOR ASSEMBLY LH (w/ Vanity Light)

Hide 74310 60.REMOVE VISOR ASSEMBLY RH (w/ Vanity Light)

HINT:

Use the same procedure as for the LH side.


Hide 74320 61.REMOVE VISOR ASSEMBLY LH (w/o Vanity Light)

a.
B461352

Using a T10H "TORX" driver, remove the 2 screws.


b.

Disengage the guide to remove the visor assembly LH.


Hide 74310 62.REMOVE VISOR ASSEMBLY RH (w/o Vanity Light)

HINT:

Use the same procedure as for the LH side.


Hide 74348 63.REMOVE VISOR HOLDER

HINT:

Use the same procedures for the opposite side.


a.
B461353C01
0,0 0,0 false
V100135

Turn in this Direction
V113147

Remove in this Direction


Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.


b.
B461354C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the base as shown in the illustration.


Hide 74612 64.REMOVE ASSIST GRIP COVER

HINT:

Use the same procedures for the opposite side.


a.
B495571C01
1.917,0.625 2.292,0.625 true 1.135,3.031 1.656,2.906 true 2.344,0.51 2.573,0.698 0.229,0.188 10 true *a 0.792,2.969 1.25,3.167 0.458,0.198 10 false SST
*a Cutout


Insert SST into the cutout of the assist grip cover as shown in the illustration.

SST
09813-00010  

NOTICE:

To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.



b.
B495572C01
2.531,1.313 2.906,1.094 true 2.979,0.99 3.323,1.167 0.344,0.177 10 true SST 2.167,1.969 2.385,2.156 0.219,0.188 10 true *a
*a 30 to 45°
V113147

Remove in this Direction


Pull SST as shown in the illustration to disengage the claw.

NOTICE:

To prevent the assist grip assembly from being damaged, make sure to only pull SST as shown in the illustration.



c.

Remove the assist grip cover.


Hide 74610A 65.REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedures for the opposite side.


a.
B461359C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clips to remove the assist grip sub-assembly as shown in the illustration.


b.
B461361

Remove the 2 clips from the vehicle body.


Hide 63311C 66.REMOVE ROOF HEADLINING

a.
B461363

for Front Pillar LH Side:

i.

Disconnect each connector.


ii.

Using a clip remover, disengage the wire harness clamps.



b.
B461362

for Front Pillar RH Side:

i.

Disconnect the connector.


ii.

Using a clip remover, disengage the wire harness clamps.



c.
B461364

for Rear Pillar RH Side:

i.

Disconnect the connector.



d.
B461365C01
0.625,1.083 0.958,1.083 true 1.229,1.906 1.229,1.573 true 1.958,1.469 1.958,1.135 true 2.573,0.865 2.906,0.865 true 0.385,0.969 0.625,1.208 0.24,0.24 12 true *A 1.865,1.5 2.104,1.76 0.24,0.26 12 true *B 2.927,0.76 3.188,1.01 0.26,0.25 12 true *C 1.146,1.906 1.417,2.146 0.271,0.24 12 true *A
*A w/ Lane Departure Alert System
*B w/ EC Mirror
*C w/ Rain Sensor


for Windshield Glass Side:

i.

Disconnect each connector.



e.
B461388

w/ Lane Departure Alert System:

i.

Remove the nut to disconnect the ground wire.



f.
B461366

Using a clip remover, remove the 3 clips.


g.

Disengage the guides to remove the roof headlining.


h.
B461367C01
0,0 0,0 false
V113147

Remove in this Direction


Turn the roof headlining diagonally and bend slightly to remove it from the back door.

NOTICE:
·

Make sure that wrinkles do not form in the roof headlining during removal.

·

Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining or vehicle interior.