Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › FRAME WIRE › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404382 FRAME WIRE A

2ZR-FXE HYBRID / BATTERY CONTROL  FRAME WIRE  INSTALLATION  


PROCEDURE

Hide 821H1 1.INSTALL HV FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


a.
A391984C01
0.083,0.177 0.354,0.396 0.271,0.219 12 true *A 0.844,1.188 1.042,1.385 0.198,0.198 10 true A 2.948,1.313 3.146,1.51 0.198,0.198 10 true B 0.104,2.573 0.375,2.792 0.271,0.219 12 true *B 2.875,3.792 3.073,3.99 0.198,0.198 10 true B 1.021,3.646 1.219,3.844 0.198,0.198 10 true A
*A for LHD
*B for RHD


Engage the clamp (B).


b.

Install a new clamp (A).


c.
A391983

Insert the HV floor under wire into the floor panel hole and engage the grommet.


d.

Install 3 new clamps in the order shown in the illustration.

A391982N01
1.083,1.75 1.24,1.948 0.156,0.198 10 true 1 3.344,1.74 3.5,1.938 0.156,0.198 10 true 2 5.958,1.75 6.115,1.948 0.156,0.198 10 true 3


e.
A391981

Install the HV floor under wire with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 51201 2.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 58165B 3.INSTALL FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.

Click hereEngine / Hybrid System>M20A-FXS (INTAKE / EXHAUST)>EXHAUST MANIFOLD>INSTALLATION


Hide 57627A 4.INSTALL REAR FLOOR SIDE MEMBER COVER RH

Hide 821H1 5.CONNECT HV FLOOR UNDER WIRE

CAUTION:

Wear insulated gloves.


a.

Connect the shield ground to the HV battery.


b.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



Hide 76974F 9.INSTALL REAR UNDER SIDE COVER LH

Hide 67918A 10.INSTALL REAR DOOR SCUFF PLATE LH

Hide 76973F 11.INSTALL REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 67917A 12.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 72693 13.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 14.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 82121 16.CONNECT ENGINE WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.

Engage the 2 clamps and connect the engine wire.


b.

Install the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.
A391971

Connect the 2 inverter with converter assembly connectors and move each lock lever as shown in the illustration.

NOTICE:
·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.

·

Do not touch the waterproof seal or terminals of the connector.