Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HV BATTERY (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404392 HV BATTERY(for LITHIUM-ION BATTERY) A

2ZR-FXE HYBRID / BATTERY CONTROL  HV BATTERY(for LITHIUM-ION BATTERY)  INSTALLATION  


PROCEDURE

Hide G9510 1.INSTALL HV BATTERY

CAUTION:

Be sure to wear insulated gloves.


a.
A378150C02
1.688,0.094 1.927,0.292 0.24,0.198 10 true *b 3.01,0.656 3.25,0.854 0.24,0.198 10 true *a 2.99,1.896 3.229,2.094 0.24,0.198 10 true *a 0.094,0.448 0.333,0.646 0.24,0.198 10 true *a
*a Bolt (A)
(Bolt Length: 25 mm (0.984 in.))
*b Bolt (B)
(Bolt Length: 24 mm (0.945 in.))


Install the HV battery to the vehicle body with the 3 bolts (A) and bolt (B).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to install it. When installing the HV battery, be careful not to damage the parts around it.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

While lowering the HV battery into the vehicle, do not allow it to contact the vehicle.

·

As bolts with 2 different lengths are used, make sure to install each bolt to the correct position.

·

If the HV battery has been struck or dropped, replace it.




Hide 82161 2.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the HV battery connector.


b.

Engage the clamp.


Hide G92PF 3.INSTALL NO. 4 HV BATTERY PROTECTOR

CAUTION:

Be sure to wear insulated gloves.


a.

Engage the 2 claws to install the No. 4 HV battery protector to the HV battery.


Hide G9290A 4.INSTALL HYBRID BATTERY HOSE ASSEMBLY

a.
A375885

Engage the 2 claws to install the hybrid battery hose assembly to the HV battery.


b.

Connect the hybrid battery hose assembly to the vehicle.


Hide 82161 5.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the HV battery junction block assembly connector.


b.

Connect the electric vehicle battery plug assembly connector.


c.

Engage the clamp.


Hide 821H1 6.CONNECT HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the shield ground to the HV battery.


b.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



Hide G92N4A 7.INSTALL NO. 1 HV BATTERY COVER PANEL RH

CAUTION:

Be sure to wear insulated gloves.


a.
A375876C01
1.344,1.177 1.635,1.177 false 0.74,0.646 0.969,0.646 0.969,0.646 1.063,0.958 true 0.542,0.573 0.854,0.771 0.313,0.198 10 false *a 1.094,0.125 1.406,0.323 0.313,0.198 10 false *b 1.667,1.094 1.979,1.292 0.313,0.198 10 false *1
*1 Battery Cover Lock Striker
*a Button
*b Push


Install the No. 1 HV battery cover panel RH to the HV battery with the 2 bolts and 3 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Install the battery cover lock striker, then push the button to lock it.


Hide G9230 8.INSTALL BATTERY COOLING BLOWER ASSEMBLY

Hide 71033 9.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY

a.
A375872N01
1.698,1.917 1.854,2.115 0.156,0.198 10 true 1 2.427,1.927 2.583,2.125 0.156,0.198 10 true 2 3.188,0.729 3.344,0.927 0.156,0.198 10 true 3 2.76,0.563 2.896,0.76 0.135,0.198 10 true 4 1.969,0.417 2.125,0.615 0.156,0.198 10 true 5 1.01,1.677 1.167,1.875 0.156,0.198 10 true 6 0.573,1.5 0.688,1.708 0.115,0.208 10 true 7 0.406,0.125 0.521,0.323 0.115,0.198 10 true 8 1.188,0.156 1.302,0.354 0.115,0.198 10 true 9

Temporarily install the rear seat cushion leg sub-assembly with the 9 bolts.


b.

Fully tighten the 9 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 76971G 10.INSTALL REAR UNDER COVER

a.

Engage the 2 guides to install the rear under cover to the rear seat cushion leg sub-assembly.


b.

Engage the 2 clips.


Hide 76974F 11.INSTALL REAR UNDER SIDE COVER LH

Hide 67918A 12.INSTALL REAR DOOR SCUFF PLATE LH

Hide 76973F 13.INSTALL REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 67917A 14.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 72693 15.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 16.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 18. PERFORM UTILITY

NOTICE:
·

Perform "Battery Status Info Update" after replacing the malfunctioning HV battery.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY

·

Perform "Prediagnostic Battery Charge" after replacing the malfunctioning HV battery.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY

·

Perform "Battery Diagnosis" after replacing the malfunctioning HV battery.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY