When the vehicle is being driven with the accelerator pedal depressed, depressing the brake pedal without releasing the accelerator pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.
The accelerator pedal and brake pedal are depressed at the same time.
Brake override control may not be performed depending on the relationship between accelerator opening and vehicle speed.
Controls driving force
When the control is operating, requested accelerator torque is controlled in accordance with the brake pedal stroke.
When the driving force is reduced to a specified level because the accelerator pedal and brake pedal are depressed at the same time, an indicator is displayed on the meter. (Operation of the system can be confirmed when the indicator is displayed on the meter.)
The accelerator pedal or brake pedal is released.
Drive at 10 km/h (6 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if driving torque is controlled when the brake pedal is depressed by the left foot of the driver, it can be confirmed that the brake override system has operated.
Perform this road test only in an appropriate safe location, in accordance with all local laws.
Pay careful attention to the surroundings when performing the road test.
The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing a loss of power (driving torque) after the accelerator and brake pedals have both been intentionally depressed, explain that this is not a malfunction, and depressing both the accelerator and brake pedals at the same time should be avoided.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: System Select / Health Check.
Check for DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| DTCs are output. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Hybrid Control / Data List / Master Cylinder Control Torque.
| Tester Display |
|---|
| Master Cylinder Control Torque |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Master Cylinder Control Torque | Braking torque equivalent to master cylinder brake fluid pressure Total braking torque Master cylinder brake fluid pressure control torque = hydraulic brake control torque + rear regenerative brake torque | - | Brake pedal depressed:
Changes with the brake pedal pressure |
Master cylinder pressure sensor |
| Result | Proceed to |
|---|---|
| Display changes according to brake pedal depression force. | A |
| Display does not change according to brake pedal depression force. | B |
Turn the power switch off.
A
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>ACCELERATOR PEDAL SENSOR>REMOVAL
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Hybrid Control / Data List / Vehicle Speed.
| Tester Display |
|---|
| Vehicle Speed |
Read the value of "Vehicle Speed" displayed on the GTS.
| Inspection Condition | Specified Condition |
|---|---|
| Vehicle stopped | 0 km/h (0 mph) |
| Vehicle being driven at a constant speed
(16 to 64 km/h (10 to 40 mph)) |
No large fluctuations in displayed speed |
Perform this road test only in an appropriate safe location, in accordance with all local laws.
Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List / All Data / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
| RR Wheel Speed |
| RL Wheel Speed |
Read the value of "FR Wheel Speed", "FL Wheel Speed", "RR Wheel Speed" and "RL Wheel Speed" displayed on the GTS.
| Inspection Condition | Specified Condition |
|---|---|
| Vehicle stopped | 0 km/h (0 mph) |
| Vehicle being driven at a constant speed
(16 to 64 km/h (10 to 40 mph)) |
No large fluctuations in displayed speed |
Perform this road test only in an appropriate safe location, in accordance with all local laws.
Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG