MALFUNCTION DESCRIPTION
These DTCs are stored when the motor temperature sensor output is abnormal. The cause of this malfunction may be one of the following:
Hybrid vehicle control ECU malfunction
Internal motor temperature sensor malfunction
Open or short in motor temperature sensor
The connectors are not connected properly
Foreign matter or water on the connector terminals
Open or short in wire harness
If any of these DTCs are stored, the motor temperature sensor is malfunctioning and the self-protection function may not operate. Therefore under certain high load driving condition, the temperature of the motor (MG2) becomes high. If the self-protection function does not operate, the motor (MG2) may malfunction and cause the vehicle to enter fail-safe mode.
The resistance of the thermistor built into the motor temperature sensor changes in accordance with changes in the motor (MG2) temperature. The lower the motor (MG2) temperature, the higher the thermistor resistance. Conversely, the higher the motor (MG2) temperature, the lower the resistance.
The term "drive motor A" indicates the motor (MG2).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A2A11 | Drive Motor "A" Temperature Sensor Circuit Short to Ground | Line short or short to ground in the motor temperature sensor circuit
(1 trip detection logic) |
·
Wire harness or connector ·
Hybrid vehicle control ECU ·
Hybrid vehicle transaxle assembly (Motor temperature sensor) |
Does not come on | Master Warning:
Comes on |
| P0A2A15 | Drive Motor "A" Temperature Sensor Circuit Short to Auxiliary Battery or Open | Open or short to +B in the motor temperature sensor circuit
(1 trip detection logic) |
·
Wire harness or connector ·
Hybrid vehicle control ECU ·
Hybrid vehicle transaxle assembly (Motor temperature sensor) |
Does not come on | Master Warning:
Comes on |
| DTC No. | Data List |
|---|---|
| P0A2A11 | Motor Temperature |
| P0A2A15 |
After confirming that DTC P0A2A11 or P0A2A15 is output, use the GTS to check "Motor Temperature" in the Data List.
| Displayed Temperature | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit or short to +B |
| 215°C (419°F) | Short circuit or short to ground |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
With power switch on (IG) and wait for 5 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Check the connection condition of the Hybrid vehicle control ECU connectors and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.
| *A | for LHD | *B | for RHD |
- The connector is connected securely.
- The terminals are not deformed and are connected securely.
- No water or foreign matter in the connector.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Check the connection condition of the motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.
For vehicles in which the intermediate connector is inside the relay block, check for signs of water intrusion inside the relay block.
- The connector is connected securely.
- The terminals are not deformed and are connected securely.
- No water or foreign matter in the connectors.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Check the connection condition of the motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.
- The connector is connected securely.
- The terminals are not deformed and are connected securely.
- No water or foreign matter in the connector.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temperature.
Read the Data List.
| Tester Display |
|---|
| Motor Temperature |
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 215°C (419°F) | B |
| Same as actual temperature | C |
Turn the power switch off.
A
B
C
Disconnect the motor temperature sensor connector.
| *a | Component without harness connected
(Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C9-1 (MMT) - C9-2 (MMTG) | Power switch off | 0.343 to 1442 kΩ |
Terminal No. 3 on the component side connector is empty.
Reconnect the motor temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(to Hybrid Vehicle Control ECU) |
Connect terminals 24 (MMT) and 23 (MMTG) of the A49 hybrid vehicle control ECU connector.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temperature.
Read the Data List.
| Tester Display |
|---|
| Motor Temperature |
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Motor Temperature | Terminals A49-24 (MMT) and A49-23 (MMTG) connected
Power switch on (IG) |
215°C (419°F) |
| Proceed to |
|---|
| OK |
| NG |
Turn the power switch off.
OK
NG
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
Disconnect the motor temperature sensor connector.
| *a | Component without harness connected
(Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C9-1 (MMT) - C9-2 (MMTG) | Power switch off | 0.343 to 1442 kΩ |
Terminal No. 3 on the component side connector is empty.
Reconnect the motor temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the motor temperature sensor connector.
Disconnect the hybrid vehicle control ECU connector.
| *a | Front view of wire harness connector
(to Motor Temperature Sensor) |
| *b | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C9-1 (MMT) - A49-24 (MMT) | Power switch off | Below 1 Ω |
| C9-2 (MMTG) - A49-23 (MMTG) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C9-1 (MMT) or A49-24 (MMT) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| C9-2 (MMTG) or A49-23 (MMTG) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Reconnect the hybrid vehicle control ECU.
Reconnect the motor temperature sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
NG