The hybrid vehicle control ECU monitors its internal operation and detects the following malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P30004B | Hybrid/EV Battery Control System Over Temperature | The HV battery temperature becomes too high due to a malfunction in the HV system.
(1 trip detection logic) |
·
Hybrid vehicle control ECU ·
HV battery ·
Battery voltage sensor |
Does not come on | Master Warning:
Comes on |
| DTC No. | Data List |
|---|---|
| P30004B | ·
Hybrid Battery Temperature 1 to 3 ·
Hybrid Battery Cooling Fan Inhaling Air Temperature ·
Ambient Temperature ·
Hybrid Battery Current ·
Hybrid Battery SOC ·
Hybrid Battery Cooling Fan 1 Drive Status ·
Hybrid Battery Cooling Fan |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Hybrid Battery Temperature 1 to 3", "Hybrid Battery Cooling Fan Inhaling Air Temperature", "Ambient Temperature" and "Hybrid Battery Current".
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
| *a | Dealer |
| *b | Battery Collection Agent |
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.
After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P30004B only is output. | A |
| DTCs other than P30004B are also output. | B |
Turn the power switch off.
A
B
| *a | Intake Port |
Check the HV battery cooling system intake port for blockage.
If anything is blocking the HV battery cooling system intake port, remove it.
Clean the No. 1 HV battery intake filter.
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>BATTERY COOLING FILTER>INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read the freeze frame data of DTC P30004B.
| *a | Freeze Frame Data Recorded |
| *b | DTC Stored |
| *c | Time |
Although freeze frame data is recorded before and after a DTC is stored, for this step it is only necessary to read the freeze frame data recorded before "0s" (when the DTC was stored).
| Result | Proceed to |
|---|---|
| Other than below | A |
| The sum of the value of each hybrid battery block voltage ("Hybrid Battery Block 1 to 9 Voltage") is less than the value of "VL-Voltage before Boosting" by 10 V or more. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read the freeze frame data of DTC P30004B.
Although freeze frame data is recorded before and after a DTC is stored, for this step it is only necessary to read the freeze frame data recorded at "0s" (when the DTC was stored).
| Result | Proceed to |
|---|---|
| Other than below | A |
| The value of any of "Hybrid Battery Temperature 1 to 3" is 80°C or more. | B |
Turn the power switch off.
A
B
Apply the parking brake and secure the wheels using chocks.
Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.
When the electric parking brake switch assembly is pulled 2 times (2 lock operations), the maximum amount of braking force is applied.
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Enter the following menus: Powertrain / Hybrid Control / Data List.
| Tester Display |
|---|
| Hybrid Battery Temperature 1 |
| Hybrid Battery Temperature 2 |
| Hybrid Battery Temperature 3 |
According to the display on the GTS, read the Data List and check that the value of each "Hybrid Battery Temperature 1 to 3" is 40°C or less.
If the value of any of "Hybrid Battery Temperature 1 to 3" is more than 40°C, turn the power switch off and wait until the values to decrease to 40°C or less before continuing this procedure.
Enter the following menus: Powertrain / Hybrid Control / Data List.
| Tester Display |
|---|
| Hybrid Battery Block 1 Voltage |
| Hybrid Battery Block 2 Voltage |
| Hybrid Battery Block 8 Voltage |
| Hybrid Battery Block 9 Voltage |
According to the display on the GTS, read the Data List and check the value of each "Hybrid Battery Block 1, 2, 8 and 9 Voltage" with the power switch on (IG).
| *a | Hybrid Battery Block 1 Voltage | *b | Hybrid Battery Block 2 Voltage |
| *c | Hybrid Battery Block 3 Voltage | *d | Hybrid Battery Block 4 Voltage |
| *e | Hybrid Battery Block 5 Voltage | *f | Hybrid Battery Block 6 Voltage |
| *g | Hybrid Battery Block 7 Voltage | *h | Hybrid Battery Block 8 Voltage |
| *i | Hybrid Battery Block 9 Voltage | - | - |
| Result | Proceed to |
|---|---|
| Other than below | A |
| The difference between the lowest and highest HV battery block voltage is 0.3 V or more. | B |
Turn the power switch off.
A
B
Apply the parking brake and secure the wheels using chocks.
Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.
When the electric parking brake switch assembly is pulled 2 times (2 lock operations), the maximum amount of braking force is applied.
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Enter the following menus: Powertrain / Hybrid Control / Data List.
| Tester Display |
|---|
| Hybrid Battery Temperature 1 |
| Hybrid Battery Temperature 2 |
| Hybrid Battery Temperature 3 |
According to the display on the GTS, read the Data List and check that the value of each "Hybrid Battery Temperature 1 to 3" is 40°C or less.
If the value of any of "Hybrid Battery Temperature 1 to 3" is more than 40°C, turn the power switch off and wait until the values to decrease to 40°C or less before continuing this procedure.
Enter the following menus: Powertrain / Hybrid Control / Data List.
| Tester Display |
|---|
| Hybrid Battery Block 3 Voltage |
| Hybrid Battery Block 4 Voltage |
| Hybrid Battery Block 5 Voltage |
| Hybrid Battery Block 6 Voltage |
| Hybrid Battery Block 7 Voltage |
According to the display on the GTS, read the Data List and check the value of each "Hybrid Battery Block 3 to 8 Voltage" with the power switch on (IG).
| *a | Hybrid Battery Block 1 Voltage | *b | Hybrid Battery Block 2 Voltage |
| *c | Hybrid Battery Block 3 Voltage | *d | Hybrid Battery Block 4 Voltage |
| *e | Hybrid Battery Block 5 Voltage | *f | Hybrid Battery Block 6 Voltage |
| *g | Hybrid Battery Block 7 Voltage | *h | Hybrid Battery Block 8 Voltage |
| *i | Hybrid Battery Block 9 Voltage | - | - |
| Result | Proceed to |
|---|---|
| Other than below | A |
| The difference between the lowest and highest HV battery block voltage is 0.3 V or more. | B |
Turn the power switch off.
A
B
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT