Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404406 HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for NICKEL METAL HYDRIDE BATTERY)  P310711  Lost Communication with Airbag System Control Module Circuit Short to Ground  


DESCRIPTION

The hybrid vehicle control ECU detects a problem in the collision signal line from the airbag sensor assembly and alerts the driver.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P310711 Lost Communication with Airbag System Control Module Circuit Short to Ground Short to ground in the communication circuit:
Communication from the airbag sensor assembly stopped and Circuit Low has been detected for a certain period.
(1 trip detection logic)
·

Wire harness or connector

·

Airbag sensor assembly

·

Hybrid vehicle control ECU


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P310711 Airbag Status (Collision)

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A409148E14
4.906,1 5.323,1.156 0.417,0.156 10 false ABFS 1.906,1 2.354,1.156 0.448,0.156 10 false GSW2 2.156,1.302 2.365,1.458 0.208,0.156 10 false E1 4.656,1 4.854,1.156 0.198,0.156 10 false 14 4.563,2.115 4.958,2.281 0.396,0.167 10 false F3 4.563,2.271 6.49,2.656 1.927,0.385 10 false Hybrid Vehicle Control ECU 1.073,2.073 1.427,2.26 0.354,0.188 10 false F150 1.063,2.25 2.833,2.448 1.771,0.198 10 false Airbag Sensor Assembly 2.396,1 2.604,1.156 0.208,0.156 10 false 24 2.396,1.302 2.604,1.458 0.208,0.156 10 false 33 5.552,0.427 5.844,0.583 0.292,0.156 10 false +B 5.781,1.552 6.094,1.75 0.313,0.198 10 false E1 6.104,1.427 6.26,1.625 0.156,0.198 10 false 3

PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.


d.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B



e.

Turn the power switch off.



A

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)
a.

Connect an oscilloscope between the airbag sensor assembly terminals specified in the table below.


b.

Turn the power switch on (READY).


c.
C371895C09
1.333,0.25 1.75,0.5 0.417,0.25 0.969,0.563 1.469,1.229 true 1.042,1.865 1.469,1.365 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.396,0.302 1.792,0.51 0.396,0.208 10 false F150 0.75,0.385 1.281,0.573 0.531,0.188 10 false GSW2 0.917,1.885 1.229,2.083 0.313,0.198 10 false E1 3.01,3.354 3.427,3.552 0.417,0.198 10 false GND
*a Component with harness connected
(Airbag sensor assembly)


Measure the waveform.

Item Contents
Terminal F150-24 (GSW2) - F150-33 (E1)
Equipment Setting 5 V/DIV., 500 ms./DIV.
Condition Power switch on (READY)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B



d.

Turn the power switch off.



A

3.CLEAR DTC

B

6.CHECK AIRBAG SENSOR ASSEMBLY
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P310711 is not output. A
P310711 is output. B



e.

Turn the power switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK AIRBAG SENSOR ASSEMBLY
a.

Disconnect the airbag sensor assembly connector.


b.
C371896C28
1.302,0.135 1.729,0.354 0.427,0.219 0.948,0.396 1.458,1.073 true 1.063,1.792 1.458,1.219 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.365,0.167 1.76,0.385 0.396,0.219 10 false F150 0.698,0.198 1.24,0.354 0.542,0.156 10 false GSW2 0.958,1.844 1.271,2 0.313,0.156 10 false E1
*a Component without harness connected
(Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F150-24 (GSW2) - F150-33 (E1) Power switch off 10 kΩ or higher



c.

Reconnect the airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG SENSOR ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the airbag sensor assembly connector.


c.
A407410C17
2.448,0.083 2.865,0.333 0.417,0.25 1.479,2.427 1.896,2.677 0.417,0.25 2.063,2.01 2.594,1.75 true 1.854,3.646 2.594,3.792 true 2.583,0.125 3.083,0.354 0.5,0.229 10 false F3 1.646,2.021 2.146,2.25 0.5,0.229 10 false ABFS 0.094,0.073 0.594,0.302 0.5,0.229 10 false *a 1.542,2.479 2.042,2.708 0.5,0.229 10 false F150 2.646,3.729 3.146,3.958 0.5,0.229 10 false GSW2 0.115,2.448 0.615,2.677 0.5,0.229 10 false *b
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-14 (ABFS) or F150-24 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Reconnect the airbag sensor assembly connector.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR