MALFUNCTION DESCRIPTION
This DTC is stored when the inverter water pump assembly is malfunctioning. The cause of this malfunction may be one of the following:
Inverter water pump assembly internal malfunction
Open or short in wire harness
Improperly connected connector
Foreign matter in inverter water pump assembly
Hybrid cooling system coolant is frozen
If this DTC is stored, the driving torque may be restricted.
The inverter water pump assembly transmits rotation speed information to the hybrid vehicle control ECU. The hybrid vehicle control ECU monitors the speed and detects malfunctions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0C7396 | Motor Electronics Coolant Pump "A" Component Internal Failure | The inverter water pump assembly revolution speed is abnormally high or low (or stopped) for 1 minute or more.
(1 trip detection logic) |
·
Inverter cooling system ·
Wire harness or connector ·
Inverter water pump assembly ·
Hybrid vehicle control ECU |
Comes on | Master Warning: Comes on |
The inverter water pump assembly operates when the power switch is on (READY).
| DTC No. | Data List |
|---|---|
| P0C7396 | ·
Inverter Water Pump Revolution ·
Inverter Water Pump Duty Ratio ·
Inverter Coolant Water Temperature |
| DTC No. | Active Test |
|---|---|
| P0C7396 | Activate the Inverter Water Pump |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Turn the power switch on (READY).
Wait for 2 minutes or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
If this vehicle is jump started, etc. and excessive voltage is applied to the auxiliary battery, the inverter water pump assembly may suspend control as a self-protection function and store DTCs.
(When the auxiliary battery voltage returns to normal, the inverter water pump assembly will resume normal operation. In this case it is not necessary to replace the inverter water pump assembly.)
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P0C7396 only is output, or DTCs except the ones in the table below are also output | A |
| Any of the following DTCs including pending DTCs are also output | B |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Microcomputer malfunction | P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure |
| P06881F | ECM/PCM Power Relay Sense Circuit Intermittent | |
| Sensor and actuator circuit malfunction | P314A31 | Motor Electronics Coolant Pump "A" No Signal |
P0C7396 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Turn the power switch off.
A
B
Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
When the inverter water pump assembly signal line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter Water Pump Revolution.
| Tester Display |
|---|
| Inverter Water Pump Revolution |
According to the display on the GTS, read the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Inverter Water Pump Revolution | Power switch on (IG) | 200 rpm or less |
When the inverter water pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
Make sure that the HV coolant level is above the low line of the inverter reserve tank.
Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Inverter Water Pump.
Select the Data List item "Inverter Water Pump Revolution".
| Active Test Display |
|---|
| Activate the Inverter Water Pump |
| Data List Display |
|---|
| Inverter Water Pump Revolution |
According to the display on the GTS, perform the Active Test "Activate the Inverter Water Pump" and, check the value of the Data List item "Inverter Water Pump Revolution".
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Inverter Water Pump Revolution | Power switch on (IG)
During Active Test |
3065 to 9302 rpm |
Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).
When the inverter water pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Result | Proceed to |
|---|---|
| Ambient Temperature value is above freezing temperature of the HV coolant | A |
| Ambient Temperature value is below freezing temperature of the HV coolant | B |
A
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the hybrid vehicle control ECU connector.
Disconnect the inverter water pump assembly connector.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| *b | Front view of wire harness connector
(to Inverter Water Pump Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-13 (IWP) - A6-3 (SWP) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-13 (IWP) or A6-3 (SWP) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.
Reconnect the inverter water pump assembly connector.
Reconnect the hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
Connect the GTS to the DLC3.
| *1 | No. 1 Engine Room Relay Block |
| *2 | INV W/PMP Fuse |
Remove the INV W/PMP fuse from No. 1 engine room relay block.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter Water Pump Revolution.
| Tester Display |
|---|
| Inverter Water Pump Revolution |
Read the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Inverter Water Pump Revolution | Power switch on (IG) | 200 rpm or less |
Turn the power switch off.
Reinstall the INV W/PMP fuse.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
Disconnect the hybrid vehicle control ECU assembly connector.
Turn the power switch on (IG).
| *a | Component with harness connected
(Hybrid Vehicle Control ECU Assembly) |
| *b | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-13 (IWP) - F2-6 (E1) | Power switch on (IG) | 11 to 14 V |
Turning the power switch on (IG) with the hybrid vehicle control ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Reconnect the hybrid vehicle control ECU assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below.
Turn the power switch on (IG).
| *a | Component with harness connected
(Hybrid Vehicle Control ECU) |
While turning the power switch on (IG), check the waveform between the hybrid vehicle control ECU terminals.
| Item | Content |
|---|---|
| Terminal | A49-13 (IWP) - F2-6 (E1) |
| Equipment Setting | 5 V/DIV., 50 ms./DIV. |
| Condition | Power switch on (IG) |
Waveform duty ratio is between 3% and 9%.
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>WATER PUMP WITH MOTOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.
Click hereGeneral>MAINTENANCE>2ZR-FXE COOLANT (for Engine Coolant)>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT