The hybrid vehicle control ECU compares the IG2 signal to the IG control status signal sent from the certification ECU (smart key ECU assembly) to detect a stuck on malfunction of the IG2 signal.
If DTC P253012 is stored, the power switch will turn off (READY off).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P253012 | IG2 Signal Circuit Short to Auxiliary Battery | The IG2 signal of the hybrid vehicle control ECU and the IG control status signal sent from the certification ECU (smart key ECU assembly) do not match.
(1 trip detection logic) |
·
Auxiliary battery ·
Certification ECU (smart key ECU assembly) ·
Hybrid vehicle control ECU ·
ECM ·
NO. 1 integration relay ·
Wire harness or connector |
Does not come on | Master Warning: Comes on |
After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and wait for 15 seconds or more.
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
Turn the power switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.
Measure the auxiliary battery voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal | 20°C (68°F), Power switch off | 12.0 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Charge or replace the auxiliary battery.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs.
Turn the power switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the power switch on (IG) and wait for 15 seconds or more.
Turn the power switch off and wait for 2 minutes or more.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P253012 is output | A |
| P253012 is not output | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| U012987, U014087, U015187, U016487 or U117087 is also output | A |
| U012987, U014087, U015187, U016487 or U117087 is not output | B |
Turn the power switch off.
A
B
Disconnect the hybrid vehicle control ECU connector.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-3 (IG2) - F2-5 (E01) | Power switch off | 9 V or higher |
Reconnect the hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID VEHICLE CONTROL ECU>REMOVAL
Disconnect the hybrid vehicle control ECU connector.
Disconnect the A38 and C63 ECM connectors.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-3 (IG2) - F2-5 (E01) | Power switch off | 9 V or higher |
Reconnect the A38 and C63 ECM connectors.
Reconnect the hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the hybrid vehicle control ECU connector.
Remove the NO. 1 integration relay from the No. 1 engine room relay block.
Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-3 (IG2) - Body ground | Power switch off | 1 V or less |
Install the NO. 1 integration relay.
Reconnect the hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
Check for intermittent problems.
Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 1 engine room relay block.
When the power switch is on (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 1 engine room relay block.
NG