Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404408 HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for LITHIUM-ION BATTERY)  P0ABF00  Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance  


DESCRIPTION

A battery current sensor, which is mounted on the positive cable side of each HV battery junction block assembly, detects the current flowing to or from the battery pack. The battery current sensor sends a voltage, which varies between 0 and 5 V in proportion to the amperage, to the IB0 terminal of the battery ECU assembly. Similarly, it sends a voltage, which varies between 0 and 5 V in inverse proportion to the amperage, to the IB1 terminal of the battery ECU assembly. When the voltage at the IB0 terminal is below 2.8 V and the voltage at the IB1 terminal is above 2.2 V, this indicates that the HV battery is being discharged. Additionally, Meanwhile, when the voltage at of the IB0 terminal is above 2.8 V and the voltage at of the IB1 terminal is below 2.2 V, this indicates that the HV battery is being charged. The battery ECU assembly sends the signals from its IB0 and IB1 terminals to the hybrid vehicle control ECU. The hybrid vehicle control ECU determines the charging and discharging amperage of the HV battery based on the received signals and calculates the SOC of the HV battery using the cumulative amperage value.

A230776E10
0.177,0.188 0.781,0.563 0.604,0.375 10 false Charging Current 1.167,0.167 1.958,0.552 0.792,0.385 10 false Discharging Current 1.219,1.271 2.177,1.625 0.958,0.354 10 false Battery Current Sensor 2.156,2.927 2.99,3.323 0.833,0.396 10 false Battery ECU Assembly 2.229,1.792 2.49,1.99 0.26,0.198 10 false VIB 2.229,1.979 2.49,2.177 0.26,0.198 10 false IB0 2.208,2.156 2.469,2.354 0.26,0.198 10 false GIB 2.219,2.323 2.479,2.521 0.26,0.198 10 false IB1 3.719,0.448 6.448,0.677 2.729,0.229 10 false Battery Current Sensor Output Voltage (V) 3.042,1.917 3.375,2.104 0.333,0.188 10 false (IB1) 6.802,2 7.135,2.188 0.333,0.188 10 false (IB0) 5.115,2.51 5.448,2.698 0.333,0.188 10 false IB0 5.896,1.802 6.229,1.99 0.333,0.188 10 false IB1 3.219,3.135 3.823,3.51 0.604,0.375 10 false Charging Current 6.365,3.156 7.156,3.542 0.792,0.385 10 false Discharging Current 4.156,3.448 5.885,3.677 1.729,0.229 10 false Hybrid Battery Current (A)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ABF00 Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance Abnormal battery current sensor characteristics:
(based on hybrid system consumption and HV battery output).
(1 trip detection logic)
·

HV battery junction block assembly

·

Battery ECU assembly

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning: Comes on

Related Data List
DTC No. Data List
P0ABF00 -

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position", "Hybrid Battery Current", "Motor Torque" and "Generator Torque".

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A439753E06
1.792,0.51 2.344,0.927 0.552,0.417 10 false VIB 2.125,0.5 2.813,0.906 0.688,0.406 10 false 1 1.823,1.156 2.375,1.573 0.552,0.417 10 false IB0 1.833,1.792 2.385,2.208 0.552,0.417 10 false IB1 1.792,2.427 2.344,2.844 0.552,0.417 10 false GIB 2.115,1.156 2.802,1.563 0.688,0.406 10 false 4 2.146,1.802 2.833,2.208 0.688,0.406 10 false 2 2.125,2.417 2.813,2.823 0.688,0.406 10 false 3 0.271,3.198 2.448,3.708 2.177,0.51 10 false Battery Current Sensor (HV Battery Junction Block Assembly) 5.125,0.5 5.677,0.917 0.552,0.417 10 false VIB 5.125,1.146 5.677,1.563 0.552,0.417 10 false IB0 5.146,1.792 5.698,2.208 0.552,0.417 10 false IB1 5.125,2.438 5.677,2.854 0.552,0.417 10 false GIB 5.052,3.323 6.781,3.542 1.729,0.219 10 false Battery ECU Assembly 4.885,0.521 5.573,0.927 0.688,0.406 10 false 24 4.885,1.156 5.573,1.563 0.688,0.406 10 false 23 4.875,1.781 5.563,2.188 0.688,0.406 10 false 11 4.885,2.427 5.573,2.833 0.688,0.406 10 false 12 3.188,0.5 3.875,0.906 0.688,0.406 10 false 1 3.927,0.49 4.615,0.896 0.688,0.406 10 false 1 3.208,1.115 3.896,1.521 0.688,0.406 10 false 7 3.948,1.115 4.635,1.521 0.688,0.406 10 false 7 3.208,1.771 3.896,2.177 0.688,0.406 10 false 2 3.938,1.771 4.625,2.177 0.688,0.406 10 false 2 3.208,2.417 3.896,2.823 0.688,0.406 10 false 6 3.917,2.417 4.604,2.823 0.688,0.406 10 false 6 5.073,3.125 5.625,3.542 0.552,0.417 10 false z23 0.271,3.031 0.823,3.448 0.552,0.417 10 false z17 3.156,3.042 3.708,3.458 0.552,0.417 10 false B 3.333,3.042 5.125,3.51 1.792,0.469 10 false Connector

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C58
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HV BATTERY (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HV BATTERY (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 HV SUPPLY STACK SUB-ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A376397N04
1.354,1.26 1.635,1.458 0.281,0.198 1.396,1.271 1.615,1.438 0.219,0.167 10 true B

Disconnect the B No. 1 HV supply stack sub-assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Disconnect the battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A377579C17
1.75,1.51 2.094,1.708 0.344,0.198 1.646,3.094 1.99,3.292 0.344,0.198 0.844,1.979 1.396,2.073 true 1.646,3.833 1.031,3.479 true 0.667,2.146 1.229,2.146 true 0.969,4.25 1.51,4.125 true 0.99,2.573 1.385,2.354 true 0.646,2.344 1.208,2.344 true 1.656,4.125 1.042,4.49 true 0.885,3.74 1.479,3.896 true 0.875,1.552 1.354,2.01 0.479,0.458 10 false *a 1.333,3.135 1.719,3.531 0.385,0.396 10 false *b 0.615,1.885 1.094,2.344 0.479,0.458 10 false IB1 1.823,1.521 2.302,1.979 0.479,0.458 10 false z23 1.771,3.115 2.25,3.573 0.479,0.458 10 false B 0.802,3.354 1.281,3.813 0.479,0.458 10 false IB1 0.396,2.073 0.875,2.531 0.479,0.458 10 false GIB 0.688,4.188 1.125,4.427 0.438,0.24 10 false GIB 0.781,2.542 1.26,3 0.479,0.458 10 false IB0 0.385,2.281 0.865,2.74 0.479,0.458 10 false VIB 0.781,4.448 1.198,4.667 0.417,0.219 10 false IB0 0.625,3.667 1.104,4.125 0.479,0.458 10 false VIB
*a Rear view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to No. 2 HV Supply Stack Sub-assembly Connector)


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z23-11 (IB1) - B-2 (IB1) Power switch off Below 1 Ω
z23-12 (GIB) - B-6 (GIB) Power switch off Below 1 Ω
z23-23 (IB0) - B-7 (IB0) Power switch off Below 1 Ω
z23-24 (VIB) - B-1 (VIB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
z23-11 (IB1) or B-2 (IB1) - Body ground and other terminals Power switch off 10 kΩ or higher
z23-12 (GIB) or B-6 (GIB) - Body ground and other terminals Power switch off 10 kΩ or higher
z23-23 (IB0) or B-7 (IB0) - Body ground and other terminals Power switch off 10 kΩ or higher
z23-24 (VIB) or B-1 (VIB) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Reconnect the battery ECU assembly connector.


g.

Reconnect the B No. 1 HV supply stack sub-assembly connector.


h.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

9.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A377612N03
1.198,0.729 1.531,0.969 0.333,0.24 1.25,0.75 1.479,0.958 0.229,0.208 10 true B

Disconnect the B No. 2 HV supply stack sub-assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A376519E01
1.427,1.313 1.781,1.542 0.354,0.229 1.458,1.333 1.729,1.542 0.271,0.208 10 true z17

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A377603C14
1.51,1.656 1.927,1.875 0.417,0.219 0.74,0.76 1.156,0.979 0.417,0.219 1.844,2.531 2.313,2.344 true 1.844,2.875 2.396,3.01 true 1.083,2.427 1.615,2.531 true 1.135,3.073 1.604,2.885 true 2,0.854 2.583,0.531 true 1.875,0.833 2.365,0.354 true 1.854,1.104 2.323,1.458 true 2,1.083 2.417,1.26 true 1.052,0.063 1.542,0.521 0.49,0.458 10 false *a 1,1.531 1.417,2.021 0.417,0.49 10 false *b 2.479,1.229 2.969,1.688 0.49,0.458 10 false GIB 2.448,0.229 2.938,0.688 0.49,0.458 10 false IB1 2.365,1.417 2.854,1.875 0.49,0.458 10 false IB0 2.625,0.458 3.115,0.917 0.49,0.458 10 false VIB 2.365,2.271 2.823,2.583 0.458,0.313 10 false IB1 0.896,3.031 1.323,3.313 0.427,0.281 10 false GIB 2.448,2.969 2.875,3.188 0.427,0.219 10 false IB0 0.833,2.354 1.323,2.813 0.49,0.458 10 false VIB 1.615,1.688 2.031,2.177 0.417,0.49 10 false z17 0.906,0.792 1.323,1.281 0.417,0.49 10 false B
*a Front view of wire harness connector
(to No. 1 HV Supply Stack Sub-assembly Connector)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly (Battery Current Sensor))


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
B-2 (IB1) - z17-2 (IB1) Power switch off Below 1 Ω
B-6 (GIB) - z17-3 (GIB) Power switch off Below 1 Ω
B-7 (IB0) - z17-4 (IB0) Power switch off Below 1 Ω
B-1 (VIB) - z17-1 (VIB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
B-2 (IB1) or z17-2 (IB1) - Body ground and other terminals Power switch off 10 kΩ or higher
B-6 (GIB) or z17-3 (GIB) - Body ground and other terminals Power switch off 10 kΩ or higher
B-7 (IB0) or z17-4 (IB0) - Body ground and other terminals Power switch off 10 kΩ or higher
B-1 (VIB) or z17-1 (VIB) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Reconnect the battery current sensor connector.


g.

Reconnect the B No. 2 HV supply stack sub-assembly connector.


h.

Install the upper hybrid battery cover sub-assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Disconnect the battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A376519

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



e.
A382897C11
1.74,1.51 2.094,1.698 0.354,0.188 1.625,3.135 1.979,3.354 0.354,0.219 1.917,3.927 2.344,3.75 true 1.906,4.271 2.396,4.354 true 1.188,3.844 1.646,3.927 true 1.146,4.365 1.677,4.271 true 1.385,2.073 0.948,1.844 true 1.375,2.354 1.01,2.646 true 1.229,2.135 0.854,2.135 true 1.208,2.313 0.833,2.313 true 1.813,1.531 2.271,1.906 0.458,0.375 10 false z23 1.698,3.167 2.156,3.542 0.458,0.375 10 false z17 2.406,3.688 2.865,4.063 0.458,0.375 10 false IB1 2.448,4.344 2.875,4.594 0.427,0.25 10 false IB0 0.948,3.771 1.406,4.146 0.458,0.375 10 false VIB 0.927,4.344 1.354,4.594 0.427,0.25 10 false GIB 0.719,1.771 1.177,2.146 0.458,0.375 10 false IB1 0.615,2.073 1.042,2.323 0.427,0.25 10 false GIB 0.625,2.271 1.083,2.646 0.458,0.375 10 false VIB 0.781,2.635 1.208,2.885 0.427,0.25 10 false IB0 1.031,1.5 1.448,1.833 0.417,0.333 10 false *a 1.167,3.01 1.656,3.594 0.49,0.583 10 false *b
*a Rear view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly (Battery Current Sensor))


Measure the resistance according to the value(s) in the tables below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z23-11 (IB1) - z17-2 (IB1) Power switch off Below 1 Ω
z23-12 (GIB) - z17-3 (GIB) Power switch off Below 1 Ω
z23-23 (IB0) - z17-4 (IB0) Power switch off Below 1 Ω
z23-24 (VIB) - z17-1 (VIB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
z23-11 (IB1) or z17-2 (IB1) - Body ground and other terminals Power switch off 10 kΩ or higher
z23-12 (GIB) or z17-3 (GIB) - Body ground and other terminals Power switch off 10 kΩ or higher
z23-23 (IB0) or z17-4 (IB0) - Body ground and other terminals Power switch off 10 kΩ or higher
z23-24 (VIB) or z17-1 (VIB) - Body ground and other terminals Power switch off 10 kΩ or higher



f.

Reconnect the battery current sensor connector.


g.

Reconnect the battery ECU assembly connector.


h.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

4.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
4.REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

5.CLEAR DTC
6.PERFORM ROAD TEST
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery SOC.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery SOC
50003 397 320

d.

Check that "Hybrid Battery SOC" shows 60% or less.

HINT:

If "Hybrid Battery SOC" is 60% or more, reduce it to below 60% by leaving the hybrid system on with shift lever in N.



e.

Apply the parking brake and secure the wheels using chocks.


f.

Turn the power switch on (READY).


g.

Move the shift lever to D while depressing the brake pedal with your left foot and repeat the following steps for 1 minute or more.

HINT:

Depress and release the accelerator pedal in 5-second intervals (2.5 seconds each) continuously.


i.

While depressing the brake pedal with your left foot, depress the accelerator pedal with your right foot.


ii.

Release the accelerator pedal.



h.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT (HYBRID CONTROL)
7.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0ABF00 is not output. A
P0ABF00 is output again. B



e.

Turn the power switch off.



A

END

B

8.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A377612N03
1.198,0.729 1.531,0.969 0.333,0.24 1.25,0.75 1.479,0.958 0.229,0.208 10 true B

Disconnect the B No. 2 HV supply stack sub-assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Check the terminals of the male side of the No. 2 HV supply stack sub-assembly connector.

OK:

The terminals are free of foreign matter and not damaged.



Result:
Proceed to
OK
NG


e.

Reconnect the B No. 2 HV supply stack sub-assembly connector.


f.

Install the upper hybrid battery cover sub-assembly.



OK

NG

9.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A377612N03
1.198,0.729 1.531,0.969 0.333,0.24 1.25,0.75 1.479,0.958 0.229,0.208 10 true B

Disconnect the B No. 2 HV supply stack sub-assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Check the terminals of the male side of the No. 2 HV supply stack sub-assembly connector.

OK:

The terminals are free of foreign matter and not damaged.



Result:
Proceed to
OK
NG


e.

Reconnect the B No. 2 HV supply stack sub-assembly connector.


f.

Install the upper hybrid battery cover sub-assembly.



OK

NG

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY AND NO. 2 HV SUPPLY STACK SUB-ASSEMBLY