Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY) › from 2019.09
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404410 HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY) C

2ZR-FXE HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM(for LITHIUM-ION BATTERY)  P0ABF11  Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground  P0ABF15  Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open  P0B0E11  Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground  P0B0E15  Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open  P1CBB12  Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery  P1CBB14  Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open  


DESCRIPTION

A battery current sensor, which is mounted on the positive cable side of each HV battery junction block assembly, detects the current flowing to or from the battery pack. The battery current sensor sends a voltage, which varies between 0 and 5 V in proportion to the amperage, to the IB0 terminal of the battery ECU assembly. Similarly, it sends a voltage, which varies between 0 and 5 V in inverse proportion to the amperage, to the IB1 terminal of the battery ECU assembly. When the voltage at the IB0 terminal is below 2.8 V and the voltage at the IB1 terminal is above 2.2 V, this indicates that the HV battery is being discharged. Additionally, Meanwhile, when the voltage at of the IB0 terminal is above 2.8 V and the voltage at of he IB1 terminal is below 2.2 V, this indicates that the HV battery is being charged. The battery ECU assembly determines the charging and discharging amount of the HV battery based on the voltages input to the IB0 terminal and IB1 terminal and calculates the SOC of the HV battery through the accumulated amperage.

A378924E03
0.229,0.615 0.969,1.073 0.74,0.458 10 false Current 0.229,0.438 0.969,0.896 0.74,0.458 10 false Charging 1.281,1.313 2.979,1.615 1.698,0.302 10 false Battery Current sensor 2.208,1.729 2.813,2.135 0.604,0.406 10 false VIB 2.208,1.938 2.813,2.344 0.604,0.406 10 false IB0 2.198,2.25 2.802,2.656 0.604,0.406 10 false GIB 2.219,2.094 2.823,2.5 0.604,0.406 10 false IB1 1.854,2.885 3.563,3.719 1.708,0.833 10 false Battery ECU Assembly 3.198,3.188 4.063,3.531 0.865,0.344 10 false Charging 4.219,3.49 5.667,3.74 1.448,0.25 10 false HV Battery Current (A) 5.156,2.521 5.667,2.76 0.51,0.24 10 false IB0 5.917,1.823 6.427,2.063 0.51,0.24 10 false IB1 3.698,0.719 4.208,0.958 0.51,0.24 10 false (V) 6.26,0.729 6.771,0.969 0.51,0.24 10 false (V) 1.219,0.438 1.958,0.896 0.74,0.458 10 false Discharging 1.219,0.615 1.958,1.073 0.74,0.458 10 false Current 3.906,0.104 6.396,0.542 2.49,0.438 10 false Battery Current Sensor Output Voltage 3.271,0.323 4.01,0.781 0.74,0.458 10 false Output 3.281,0.5 4.021,0.958 0.74,0.458 10 false Voltage 3.271,0.688 4.01,1.146 0.74,0.458 10 false (IB1) 6.531,0.344 7.052,0.792 0.521,0.448 10 false Output 6.542,0.531 7.094,0.938 0.552,0.406 10 false Voltage 6.542,0.719 6.99,1.177 0.448,0.458 10 false (IB0) 3.198,3.344 4.063,3.688 0.865,0.344 10 false Current 6.333,3.229 7.146,3.667 0.813,0.438 10 false Discharging 6.313,3.396 6.958,3.75 0.646,0.354 10 false Current

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ABF11 Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground The battery current sensor output voltage (IB0) is excessively low.
(1 trip detection logic)
·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
P0ABF15 Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open The battery current sensor output voltage (IB0) is excessively high.
(1 trip detection logic)
·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
P0B0E11 Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground The battery current sensor output voltage (IB1) is excessively low.
(1 trip detection logic)
·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
P0B0E15 Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open The battery current sensor output voltage (IB1) is excessively high.
(1 trip detection logic)
·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
P1CBB12 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery Power source voltage (VIB) of the battery current sensor is excessively high.
(1 trip detection logic)
·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on
P1CBB14 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open Power source voltage (VIB) of the battery current sensor is excessively low.
(1 trip detection logic)
·

HV battery junction block assembly

·

Battery ECU assembly

·

Wire harness or connector

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0ABF11 Hybrid Battery Current
P0ABF15
P0B0E11
P0B0E15
P1CBB12
P1CBB14

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A378922E25
1.792,0.51 2.344,0.927 0.552,0.417 10 false VIB 2.125,0.5 2.813,0.906 0.688,0.406 10 false 1 1.823,1.156 2.375,1.573 0.552,0.417 10 false IB0 1.833,1.792 2.385,2.208 0.552,0.417 10 false IB1 1.792,2.427 2.344,2.844 0.552,0.417 10 false GIB 2.115,1.156 2.802,1.563 0.688,0.406 10 false 4 2.146,1.802 2.833,2.208 0.688,0.406 10 false 2 2.125,2.417 2.813,2.823 0.688,0.406 10 false 3 0.552,3.073 2.469,3.344 1.917,0.271 10 false z17 5.125,0.5 5.677,0.917 0.552,0.417 10 false VIB 5.125,1.146 5.677,1.563 0.552,0.417 10 false IB0 5.146,1.792 5.698,2.208 0.552,0.417 10 false IB1 5.125,2.438 5.677,2.854 0.552,0.417 10 false GIB 4.802,3.125 6.594,3.594 1.792,0.469 10 false z23 4.885,0.521 5.573,0.927 0.688,0.406 10 false 24 4.885,1.156 5.573,1.563 0.688,0.406 10 false 23 4.875,1.781 5.563,2.188 0.688,0.406 10 false 11 4.885,2.427 5.573,2.833 0.688,0.406 10 false 12 5.073,3.125 6.865,3.594 1.792,0.469 10 false Battery ECU Assembly 0.833,3.083 3.021,3.479 2.188,0.396 10 false Battery Current Sensor (HV Battery Junction Block Assembly)

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HV BATTERY (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HV BATTERY (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery and Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
"P0ABF11, P0ABF15, P0B0E11, P0B0E15, P1CBB12 or P1CBB14" only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid battery system in the table below are output. B
DTCs of hybrid control system in the table below are output. C


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


e.

Turn the power switch off.



A

2.CHECK BATTERY ECU ASSEMBLY (IGCT VOLTAGE)

B

C

2.CHECK BATTERY ECU ASSEMBLY (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A376410C50
1.615,1.927 2.031,2.146 0.417,0.219 0.875,3.104 1.302,2.99 true 1.875,2.698 2.615,2.26 true 0.302,0.146 0.708,0.479 0.406,0.333 10 false *a 1.719,1.958 2.156,2.396 0.438,0.438 10 false z22 0.552,3.094 1.021,3.354 0.469,0.26 10 false IGCT 2.656,2.177 3.125,2.438 0.469,0.26 10 false GND
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z22-16 (IGCT) - z22-4 (GND) Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified.

·

Installation condition of fuse(s) (before removing fuse(s)) (IG circuit)

·

Fuse condition (before and after removing fuse(s)) (IG circuit)

·

Connection condition of connectors (IG circuit)

·

Wire harness condition (IG circuit)

·

Wire harness condition (GND circuit)




f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY ECU ASSEMBLY POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (NO. 2 HV SUPPLY STACK SUB-ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

OK

4.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 HV SUPPLY STACK SUB-ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - NO. 1 HV SUPPLY STACK SUB-ASSEMBLY)

OK

5.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)

NG

5.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A377566C61
1.521,2.292 1.927,2.573 0.406,0.281 0.448,3.823 0.906,3.406 true 0.375,2.802 0.906,3.073 true 1.615,2.344 2.146,2.76 0.531,0.417 10 false z23 0.198,3.854 0.604,4.125 0.406,0.271 10 false VIB 0.104,2.708 0.51,2.979 0.406,0.271 10 false GIB 0.698,2.083 1.104,2.354 0.406,0.271 10 false *a
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z23-24 (VIB) - z23-12 (GIB) Power switch on (IG) 4.6 to 5.4 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

6.CHECK BATTERY ECU ASSEMBLY (GIB - GND)

NG

14.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)
6.CHECK BATTERY ECU ASSEMBLY (GIB - GND)

b.

Measure the resistance according to the value(s) in the tables below.

A380451C07
5.094,1.823 5.5,2.083 0.406,0.26 2.042,1.948 2.448,2.208 0.406,0.26 5.458,2.51 6.042,1.979 true 1.771,2.583 1.042,2.281 true 0.219,0.073 0.802,0.688 0.583,0.615 10 false *a 5.198,1.865 5.771,2.229 0.573,0.365 10 false z22 6.094,1.885 6.667,2.25 0.573,0.365 10 false GND 0.802,2.208 1.375,2.573 0.573,0.365 10 false GIB 2.135,2 2.708,2.365 0.573,0.365 10 false z23
*a Component without harness connected
(Battery ECU Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
z23-12 (GIB) - z22-4 (GND) Power switch off Below 1 Ω



c.

Install the battery ECU assembly.


Result:
Proceed to
OK
NG



OK

7.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB1))

NG

7.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB1))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A377566C62
1.521,2.292 1.927,2.573 0.406,0.281 0.406,3.479 1.042,3.177 true 0.375,2.802 0.885,3.083 true 1.635,2.333 2.167,2.75 0.531,0.417 10 false z23 0.167,3.417 0.573,3.688 0.406,0.271 10 false IB1 0.125,2.688 0.531,2.958 0.406,0.271 10 false GIB 0.719,2.063 1.125,2.333 0.406,0.271 10 false *a
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z23-11 (IB1) - z23-12 (GIB) Power switch on (IG) 2.1 to 2.3 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

8.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB0))

NG

12.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB1))
8.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB0))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A377566C63
1.521,2.292 1.927,2.573 0.406,0.281 1,3.406 0.396,3.771 true 0.375,2.802 0.865,3.073 true 1.635,2.333 2.167,2.75 0.531,0.417 10 false z23 0.167,3.698 0.573,3.969 0.406,0.271 10 false IB0 0.104,2.719 0.51,2.99 0.406,0.271 10 false GIB 0.719,2.063 1.125,2.333 0.406,0.271 10 false *a
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z23-23 (IB0) - z23-12 (GIB) Power switch on (IG) 2.7 to 2.9 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

NG

9.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB0))
9.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB0))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A377566C63
1.521,2.292 1.927,2.573 0.406,0.281 1,3.406 0.396,3.771 true 0.375,2.802 0.865,3.073 true 1.635,2.333 2.167,2.75 0.531,0.417 10 false z23 0.167,3.698 0.573,3.969 0.406,0.271 10 false IB0 0.104,2.719 0.51,2.99 0.406,0.271 10 false GIB 0.719,2.063 1.125,2.333 0.406,0.271 10 false *a
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Tester Connection Condition
z23-23 (IB0) - z23-12 (GIB) Power switch on (IG)

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 HV battery protector.


Result:
Result Proceed to
0.4 to 4.6 V A
Below 0.4 V B
4.6 V or higher C



A

B

10.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB0))

C

11.CHECK BATTERY ECU ASSEMBLY (VIB - IB0)
10.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB0))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A376519N18
1.427,1.313 1.781,1.542 0.354,0.229 1.458,1.333 1.74,1.51 0.281,0.177 10 true z17

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A377566C63
1.521,2.292 1.927,2.573 0.406,0.281 1,3.406 0.396,3.771 true 0.375,2.802 0.865,3.073 true 1.635,2.333 2.167,2.75 0.531,0.417 10 false z23 0.167,3.698 0.573,3.969 0.406,0.271 10 false IB0 0.104,2.719 0.51,2.99 0.406,0.271 10 false GIB 0.719,2.063 1.125,2.333 0.406,0.271 10 false *a
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z23-23 (IB0) - z23-12 (GIB) Power switch on (IG) 4.6 to 5.4 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the battery current sensor connector to the HV battery junction block assembly.


j.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

NG

11.CHECK BATTERY ECU ASSEMBLY (VIB - IB0)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A376519N18
1.427,1.313 1.781,1.542 0.354,0.229 1.458,1.333 1.74,1.51 0.281,0.177 10 true z17

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A251028C82
2.323,0.927 2.75,1.188 0.427,0.26 1.531,1.094 0.99,0.906 true 2.594,1.688 1.906,1.583 true 0.729,0.823 1.063,1.063 0.333,0.24 10 false VIB 2.656,1.646 3.021,1.896 0.365,0.25 10 false IB0 0.188,0.146 0.427,0.292 0.24,0.146 10 false *a 2.396,0.969 2.906,1.354 0.51,0.385 10 false z17
*a Front view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
z17-1 (VIB) - z17-4 (IB0) Power switch off 10 kΩ or higher



e.

Reconnect the battery current sensor connector to the HV battery junction block assembly.


f.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

NG

12.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB1))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A377566C62
1.521,2.292 1.927,2.573 0.406,0.281 0.406,3.479 1.042,3.177 true 0.375,2.802 0.885,3.083 true 1.635,2.333 2.167,2.75 0.531,0.417 10 false z23 0.167,3.417 0.573,3.688 0.406,0.271 10 false IB1 0.125,2.688 0.531,2.958 0.406,0.271 10 false GIB 0.719,2.063 1.125,2.333 0.406,0.271 10 false *a
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition
z23-11 (IB1) - z23-12 (GIB) Power switch on (IG)


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 HV battery protector.


Result:
Result Proceed to
0.4 to 4.6 V A
Below 0.4 V B
4.6 V or higher C



A

B

13.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB1))

C

15.CHECK BATTERY ECU ASSEMBLY (VIB - IB1)
13.CHECK BATTERY ECU ASSEMBLY (BATTERY CURRENT SENSOR OUTPUT VOLTAGE (IB1))
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A376519N18
1.427,1.313 1.781,1.542 0.354,0.229 1.458,1.333 1.74,1.51 0.281,0.177 10 true z17

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A377566C62
1.521,2.292 1.927,2.573 0.406,0.281 0.406,3.479 1.042,3.177 true 0.375,2.802 0.885,3.083 true 1.635,2.333 2.167,2.75 0.531,0.417 10 false z23 0.167,3.417 0.573,3.688 0.406,0.271 10 false IB1 0.125,2.688 0.531,2.958 0.406,0.271 10 false GIB 0.719,2.063 1.125,2.333 0.406,0.271 10 false *a
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z23-11 (IB1) - z23-12 (GIB) Power switch on (IG) 4.6 to 5.4 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the battery current sensor connector to the HV battery junction block assembly.


j.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

NG

14.CHECK BATTERY ECU ASSEMBLY (VIB VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A376519N18
1.427,1.313 1.781,1.542 0.354,0.229 1.458,1.333 1.74,1.51 0.281,0.177 10 true z17

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A377566C61
1.521,2.292 1.927,2.573 0.406,0.281 0.448,3.823 0.906,3.406 true 0.375,2.802 0.906,3.073 true 1.615,2.344 2.146,2.76 0.531,0.417 10 false z23 0.198,3.854 0.604,4.125 0.406,0.271 10 false VIB 0.104,2.708 0.51,2.979 0.406,0.271 10 false GIB 0.698,2.083 1.104,2.354 0.406,0.271 10 false *a
*a Component with harness connected
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z23-24 (VIB) - z23-12 (GIB) Power switch on (IG) 4.6 to 5.4 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the battery current sensor connector to the HV battery junction block assembly.


j.

Install the No. 1 HV battery protector.


Result:
Proceed to
OK
NG



OK

NG

15.CHECK BATTERY ECU ASSEMBLY (VIB - IB1)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A376519N18
1.427,1.313 1.781,1.542 0.354,0.229 1.458,1.333 1.74,1.51 0.281,0.177 10 true z17

Disconnect the battery current sensor connector from the HV battery junction block assembly.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A251028C83
2.323,0.927 2.729,1.219 0.406,0.292 1.531,1.094 0.99,0.906 true 2.594,1.719 1.885,1.26 true 0.729,0.823 1.063,1.063 0.333,0.24 10 false VIB 2.656,1.646 3.021,1.896 0.365,0.25 10 false IB1 0.188,0.146 0.427,0.292 0.24,0.146 10 false *a 2.406,0.99 2.865,1.26 0.458,0.271 10 false z17
*a Front view of wire harness connector
(to HV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
z17-1 (VIB) - z17-2 (IB1) Power switch off 10 kΩ or higher



e.

Reconnect the battery current sensor connector from the HV battery junction block assembly.


f.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

NG