Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HYBRID CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404411 HYBRID CONTROL SYSTEM C

M20A-FXS HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P253012  IG2 Signal Circuit Short to Auxiliary Battery  


DESCRIPTION

The hybrid vehicle control ECU compares the IG2 signal to the IG control status signal sent from the certification ECU (smart key ECU assembly) to detect a stuck on malfunction of the IG2 signal.

HINT:

If DTC P253012 is stored, the power switch will turn off (READY off).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P253012 IG2 Signal Circuit Short to Auxiliary Battery The IG2 signal of the hybrid vehicle control ECU and the IG control status signal sent from the certification ECU (smart key ECU assembly) do not match.
(1 trip detection logic)
·

Auxiliary battery

·

Certification ECU (smart key ECU assembly)

·

Hybrid vehicle control ECU

·

ECM

·

NO. 1 integration relay

·

Wire harness or connector


Does not come on Master Warning: Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and wait for 15 seconds or more.

6.

Turn the power switch off and wait for 2 minutes or more.

7.

Turn the power switch on (IG) and turn the GTS on.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A452373E01
0.083,0.823 0.958,1.563 0.875,0.74 10 false from Auxiliary Battery 1.365,0.99 2.594,1.188 1.229,0.198 10 false IG2-MAIN 2.781,1.573 4.01,1.771 1.229,0.198 10 false IG2 NO. 1 4.115,0.99 5.344,1.188 1.229,0.198 10 false ECU-IG2 NO. 1 5.875,0.729 6.271,1.031 0.396,0.302 10 false IG2 5.438,1.771 7.156,2.146 1.719,0.375 10 false Hybrid Vehicle Control ECU 1.771,0.708 1.927,0.906 0.156,0.198 10 false 2 1.417,0.708 1.573,0.906 0.156,0.198 10 false 1 2.281,0.729 2.531,0.99 0.25,0.26 10 false 10 2.344,1.146 2.5,1.344 0.156,0.198 10 false 8 3.635,0.74 3.792,0.938 0.156,0.198 10 false 9 3.635,1.146 3.792,1.344 0.156,0.198 10 false 7 4.385,0.719 4.542,0.917 0.156,0.198 10 false 1 4.75,0.719 4.906,0.917 0.156,0.198 10 false 2 5.677,2.281 5.833,2.479 0.156,0.198 10 false 2 5.615,2.625 5.854,2.875 0.24,0.25 10 false 10 5.615,3.75 5.875,3.979 0.26,0.229 10 false 17 5.448,1.583 5.865,1.76 0.417,0.177 10 false F160 5.625,1.167 5.927,1.438 0.302,0.271 10 false 12 2.323,2.01 2.573,2.26 0.25,0.25 10 false 1A 2.344,2.188 4.177,2.521 1.833,0.333 10 false NO. 1 Integration Relay 5.625,0.74 5.865,0.979 0.24,0.24 10 false 35 5.667,3.125 6.063,3.427 0.396,0.302 10 false A96 4.281,4.135 4.51,4.323 0.229,0.188 10 false F1 5.875,3.865 6.271,4.167 0.396,0.302 10 false IG1D 5.875,2.385 6.333,2.635 0.458,0.25 10 false IGSW 5.885,1.26 6.344,1.51 0.458,0.25 10 false E01 5.885,2.75 6.344,3 0.458,0.25 10 false E1 4.281,4.302 7.125,4.542 2.844,0.24 10 false Certification ECU (Smart Key ECU Assembly) 6.031,3.135 6.448,3.448 0.417,0.313 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.CHECK AUXILIARY BATTERY VOLTAGE
a.

Turn the power switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.


b.

Measure the auxiliary battery voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal 20°C (68°F), Power switch off 12.0 V or higher


Result:
Proceed to
OK
NG




OK

3.CLEAR DTC

NG

2.CHARGE OR REPLACE AUXILIARY BATTERY
2.CHARGE OR REPLACE AUXILIARY BATTERY
a.

Charge or replace the auxiliary battery.


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397

e.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Turn the power switch on (IG) and wait for 15 seconds or more.


b.

Turn the power switch off and wait for 2 minutes or more.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P253012 is output A
P253012 is not output B



g.

Turn the power switch off.



A

5.CHECK DTC OUTPUT (HYBRID CONTROL)

B

5.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
U012987, U014087, U015187, U016487 or U117087 is also output A
U012987, U014087, U015187, U016487 or U117087 is not output B



e.

Turn the power switch off.



A

6.CHECK HYBRID VEHICLE CONTROL ECU

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK HYBRID VEHICLE CONTROL ECU
a.
A452468C09
1.542,0.146 1.99,0.427 0.448,0.281 2.667,1.406 2.417,1.833 true 2.719,1.146 3,1.833 true 1.604,0.208 2.115,0.51 0.51,0.302 10 false F160 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.313,1.865 2.646,2.104 0.333,0.24 10 false IG2 2.938,1.875 3.271,2.115 0.333,0.24 10 false E01
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Disconnect the hybrid vehicle control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Condition:
Tester Connection Condition
F160-35 (IG2) - F160-12 (E01) Power switch off



c.

Reconnect the hybrid vehicle control ECU connector.


Result:
Result Proceed to
9 V or higher A
Below 9 V B



A

7.CHECK ECM

B

7.CHECK ECM
a.
A452468C10
1.573,0.167 1.99,0.406 0.417,0.24 2.667,1.406 2.417,1.833 true 2.719,1.146 3,1.833 true 1.646,0.208 2.115,0.448 0.469,0.24 10 false F160 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.313,1.865 2.646,2.104 0.333,0.24 10 false IG2 2.938,1.875 3.271,2.115 0.333,0.24 10 false E01
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the A96 ECM connector.


c.

Measure the voltage according to the value(s) in the table below.

Condition:
Tester Connection Condition
F160-35 (IG2) - F160-12 (E01) Power switch off



d.

Reconnect the A96 ECM connector.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Result Proceed to
9 V or higher A
Below 9 V B



A

8.INSPECT NO. 1 INTEGRATION RELAY (IG2 NO. 1 RELAY)

B

8.INSPECT NO. 1 INTEGRATION RELAY (IG2 NO. 1 RELAY)

OK

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 INTEGRATION RELAY)

NG

9.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Remove the NO. 1 integration relay from the No. 1 engine room relay block.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


c.
A452468C11
1.604,0.167 2.01,0.417 0.406,0.25 2.667,1.417 2.833,1.833 true 1.656,0.219 2.063,0.448 0.406,0.229 10 false F160 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 2.781,1.865 3.104,2.135 0.323,0.271 10 false IG2
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F160-35 (IG2) - Body ground Power switch off 1 V or less



d.

Install the NO. 1 integration relay.


e.

Reconnect the hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

CHECK FOR INTERMITTENT PROBLEMS
a.

Check for intermittent problems.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

i.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 1 engine room relay block.


ii.

When the power switch is on (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 1 engine room relay block.




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR