Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › MOTOR GENERATOR CONTROL SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404412 MOTOR GENERATOR CONTROL SYSTEM C

M20A-FXS HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL SYSTEM  P1CCC96  DC/DC Converter Enable Component Internal Failure  


DESCRIPTION

The DC/DC converter converts the DC 216.0 V of the HV battery into DC 12 V in order to supply power to areas such as the vehicle lighting system, audio system and various ECUs. Additionally, it charges the auxiliary battery.

A transistor bridge circuit initially converts DC 216.0 V into alternating current, and a transformer lowers the voltage.

The DC/DC converter controls the output voltage in order to keep a constant voltage at the terminals of the auxiliary battery.

Then, it is rectified and smoothed (into direct current) and converted into DC 12 V.

The motor generator control ECU sends a signal to the DC/DC converter to prohibit its control and receives signals indicating a normal or abnormal condition of the 12 V charging system via the NODD signal line.

If the DC/DC converter malfunctions, the vehicle will become inoperative. Therefore, the motor generator control ECU monitors the operation of the DC/DC converter and detects malfunctions.

This DTC is stored when the DC/DC converter circuit has a malfunction or its operation is prohibited by a fail-safe function, or the auxiliary battery voltage drops to 11 V or less with the power switch on (READY).

If a DC/DC converter malfunction occurs, DC/DC converter malfunction signals are sent from the DC/DC converter to the MG ECU via the NODD signal line.

This DTC may also be stored if a malfunction of the inverter cooling system (blockage, inverter water pump malfunction, etc.) or a high-voltage insulation malfunction occurs.

A414648E02
1.021,0.948 1.792,1.146 0.771,0.198 10 false DC/DC 2.052,0.906 2.823,1.104 0.771,0.198 10 false AMD 5.229,0.292 6.042,0.479 0.813,0.188 10 false DC 216.0 V 4.115,2.177 4.885,2.375 0.771,0.198 10 false NODD 4.615,2.177 5.385,2.375 0.771,0.198 10 false VLO 2.469,2.427 3.771,2.615 1.302,0.188 10 false DC/DC Converter 3.167,2.844 5.26,3.073 2.094,0.229 10 false Motor Generator Control ECU 4.167,3.448 6.333,3.688 2.167,0.24 10 false Inverter with Converter Assembly 3.302,4.104 5.104,4.323 1.802,0.219 10 false Hybrid Vehicle Control ECU 1.052,3.594 2.75,3.802 1.698,0.208 10 false from IGCT NO. 2 Fuse 0.104,3.917 1.542,4.156 1.438,0.24 10 false from Auxiliary Battery

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1CCC96 DC/DC Converter Enable Component Internal Failure Both of the following conditions are met:
·

The DC/DC converter is malfunctioning and the auxiliary battery voltage is 11 V or less.*1

·

The inverter coolant temperature is 70 °C or lower for 60 seconds.


(1 trip detection logic)
·

DC/DC fuse

·

Engine wire

·

Inverter cooling system

·

Cooling fan system

·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Motor cable


Does not come on Master Warning:
Comes on

HINT:

*1: If the DC/DC converter is malfunctioning, its operation and charging will be stopped and the auxiliary battery voltage will drop.


WIRING DIAGRAM

Refer to the wiring diagram for the Generator High-voltage Circuit.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>Generator High-voltage Circuit

Refer to the wiring diagram for the Motor High-voltage Circuit.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>Motor High-voltage Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C56
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

After repair, clear the DTCs, turn the power switch off and wait for 30 seconds or more and perform the following procedure to confirm that the auxiliary battery low voltage indicated by this DTC has been repaired.

(a)

Wait for 2 minutes with the shift lever in P, the power switch on (READY) and the following conditions met, then confirm that Data List item "BATT Voltage (Hybrid control system)" is between 13.0 and 15.0 V.

(If charging is not performed and the electrical load increases, +B voltage may not be steady and will gradually drop.)

(1)

Headlight switch is in the HI position.

(2)

A/C blower fan switch is in the HI position.

(3)

Window defogger switch is turned on.



·

By performing the following procedure, the DC/DC converter function can be checked.

(a)

Connect the AC/DC 400 A probe to the positive (+) auxiliary battery cable.

(1)

Turn the power switch on (READY) and leave the vehicle as is until the electric current flowing to the auxiliary battery becomes 10 A or less.

(2)

Turn the power switch on (READY) and turn the headlight switch and A/C blower fan switch to the HI position and the window defogger on.

(3)

Confirm that the current drawn from the auxiliary battery is 0 A or lower and the auxiliary battery voltage is between 12.5 and 15.0 V.




·

This DTC may be also stored when a part other than the DC/DC converter is malfunctioning or depending on user operation.


·

If this vehicle is used to jump start another vehicle with a discharged battery, a fuse may blow due to overcurrent or the DC/DC converter self-protection may be activated. Also, if this vehicle is jump started by a vehicle with a 24 V battery, the same malfunction may occur and this DTC may be stored. (The suspended DC/DC converter control will return to normal by clearing the DTCs and turning the power switch off.)


·

Confirm that high electrical load equipment such as a high-capacitance audio device or electric kettle is used in the vehicle. (A fuse of the auxiliary battery may be blown due to overcurrent.)


·

If the DC/DC converter is malfunctioning, the auxiliary battery cannot be charged. Therefore, once the power switch is turned off, it may be impossible to turn it on (READY) again if the auxiliary battery is completely discharged. In this case, charge the auxiliary battery. Be careful as charging is not performed during the inspection.


·

If the power switch turns off immediately after it is turned on (READY), the auxiliary battery voltage may be low. Charge the auxiliary battery.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > Motor Generator > Trouble Codes
50001 395
Result:
Result Proceed to
P1CCC96 only is output, or DTCs except the ones in the table below are also output. A
DTCs of hybrid control system in the table below are output. B
DTCs of motor generator control system in the table below are output. C


Table 1
Malfunction Content System Relevant DTC
Insulation Malfunction Hybrid control system P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure
P1C7D49 Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure
P1C7E49 Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure
P1C7F49 Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure
High Voltage Circuit Malfunction Hybrid control system P0AA649 Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure
P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0AE411 Hybrid/EV Battery Precharge Contactor Circuit Short to Ground
P1C8449 High Voltage Power Resource Circuit Short during Ready ON
P300449 High Voltage Power Resource Circuit Short during Pre-Charge

Table 2
Malfunction Content System Relevant DTC
System malfunction Hybrid control system P0A9300 Inverter "A" Cooling System Performance
P0C7396 Motor Electronics Coolant Pump "A" Component Internal Failure
P314A31 Motor Electronics Coolant Pump "A" No Signal
Motor generator control system P0E5717 DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold

HINT:

P1CCC96 may be output as a result of the malfunction indicated by the DTCs above.

1.

The chart above is listed in inspection order of priority.

2.

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)




e.

Turn the power switch off.



A

2.CHECK AMD TERMINAL VOLTAGE

B

C

2.CHECK AMD TERMINAL VOLTAGE
CAUTION:

Be sure to wear insulated gloves.


a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.
A452304C02
0.802,0.833 0.458,0.448 true 2.563,0.646 2.302,0.396 true 0.292,0.302 0.51,0.479 0.219,0.177 10 true *1 2.104,0.198 2.333,0.417 0.229,0.219 10 true *2 2.958,0.208 3.188,0.406 0.229,0.198 10 true 1F
*1 AMD Terminal (Inverter with Converter Assembly Side)
*2 AMD Terminal (No. 1 Engine Room Relay Block Side)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1F-1 (AMD) - Body ground Power switch off Same as auxiliary battery voltage



c.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

3.CHECK AMD TERMINAL CONNECTION CONDITION

NG

7.CHECK FUSE (DC/DC)
3.CHECK AMD TERMINAL CONNECTION CONDITION
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A452304C01
0.802,0.833 0.458,0.448 true 2.563,0.646 2.302,0.396 true 0.292,0.302 0.51,0.479 0.219,0.177 10 true *1 2.104,0.198 2.333,0.417 0.229,0.219 10 true *2
*1 AMD Terminal (Inverter with Converter Assembly Side)
*2 AMD Terminal (No. 1 Engine Room Relay Block Side)


Check that the bolts for the AMD terminal are tightened to the specified torque, the AMD terminal is connected securely, and there are no contact problems.

Torque:

T=8.0 N*m (82 kgf*cm, 71 in.*lbf)


Result:
Result Proceed to
There are no arc marks. The terminal is connected securely and there are no contact problems. A
There are no arc marks. The terminal is not connected securely and there is a contact problem. B
There are arc marks. - C




A

4.CHECK ENGINE WIRE

B

CONNECT SECURELY

C

REPLACE MALFUNCTIONING PARTS

4.CHECK ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the engine wire from the AMD terminal (inverter with converter assembly side and auxiliary battery side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C102-1 (AMD) - 1F-1 (AMD) Always Below 1 Ω



d.

Install the engine wire.


Result:
Proceed to
OK
NG



OK

5.CHECK COOLING SYSTEM

NG

5.CHECK COOLING SYSTEM

NEXT

6.CHECK DC/DC CONVERTER FUNCTION
6.CHECK DC/DC CONVERTER FUNCTION
HINT:

The current at the AMD terminal cannot be measured directly because of space limitations. Measure the current flowing at the auxiliary battery instead.


a.

Connect the AC/DC 400 A probe of the tester to the positive (+) auxiliary battery cable.


b.

Install the service plug grip.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (READY) and leave the vehicle as it is until the electric current flowing to the auxiliary battery becomes 10 A or less.

HINT:

If the power switch turns off immediately after it is turned on (READY), auxiliary battery voltage may be low. Recharge the auxiliary battery and perform this procedure again.



e.
A111747C08
0.688,1.031 1.146,0.646 1.146,0.646 1.281,0.646 true 1.177,1.26 0.896,1.656 0.896,1.656 0.75,1.656 false 1.302,0.563 1.49,0.719 0.188,0.156 10 false *a 0.552,1.563 0.75,1.708 0.198,0.146 10 false *b
*a Probe Direction
*b Current Flowing to Auxiliary Battery


A111748C08
0.729,1.042 1.146,0.646 1.146,0.646 1.281,0.646 false 1.281,1.26 0.896,1.656 0.896,1.656 0.75,1.656 false 1.302,0.563 1.479,0.719 0.177,0.156 10 false *a 0.552,1.563 0.729,1.719 0.177,0.156 10 false *b
*a Probe Direction
*b Current Flowing from Auxiliary Battery


Measure the current flowing from the auxiliary battery with the power switch on (READY), the headlight position switch and blower motor switch in the HI position, and the rear window defogger turned on.

Standard Current:
Item Condition Specified Condition
Current flowing from auxiliary battery Power switch on (READY)
(The headlight position switch and blower motor switch are in the HI position, and the rear window defogger is turned on.)
0 A or less
(no current from auxiliary battery)



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Item Condition Specified Condition
Auxiliary battery voltage Power switch on (READY)
(The headlight position switch and blower motor switch are in the HI position, and the rear window defogger is turned on.)
12.5 to 15 V



g.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

8.CHECK HIGH VOLTAGE INSULATION
7.CHECK FUSE (DC/DC)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A436199C01
0.958,4.188 1.427,3.271 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *1 0.885,4.198 1.198,4.396 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block Assembly
*2 DC/DC fuse


Remove the DC/DC fuse from No. 1 engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DC/DC fuse Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE WIRE HARNESS

NG

REPLACE FUSE (DC/DC)

8.CHECK HIGH VOLTAGE INSULATION
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the inverter cover from the inverter with converter assembly.


c.
A376322E11
1.198,0.26 1.542,0.51 0.344,0.25 1.25,0.292 1.51,0.469 0.26,0.177 10 true i4 2.813,0.823 2.969,1.021 0.156,0.198 10 true 1 2.281,1.24 2.438,1.438 0.156,0.198 10 true 2 1.521,1.396 1.677,1.594 0.156,0.198 10 true 4 1.156,1.375 1.313,1.573 0.156,0.198 10 true 5 0.552,0.948 0.708,1.146 0.156,0.198 10 true 6 1.917,1.365 2.073,1.563 0.156,0.198 10 true 3

Using a megohmmeter set to 500 V, measure the insulation resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
i4-1 (W) - Body ground and shield ground Power switch off 1 MΩ or higher
i4-2 (U) - Body ground and shield ground Power switch off 1 MΩ or higher
i4-3 (V) - Body ground and shield ground Power switch off 1 MΩ or higher
i4-4 (W) - Body ground and shield ground Power switch off 1 MΩ or higher
i4-5 (U) - Body ground and shield ground Power switch off 1 MΩ or higher
i4-6 (V) - Body ground and shield ground Power switch off 1 MΩ or higher


HINT:

Perform this inspection while the motor cable are connected.



d.

Install the inverter cover to the inverter with converter assembly.


Result:
Proceed to
OK
NG



OK

NG

9.CHECK GENERATOR HIGH-VOLTAGE CIRCUIT
9.CHECK GENERATOR HIGH-VOLTAGE CIRCUIT

NEXT

10.CHECK MOTOR HIGH-VOLTAGE CIRCUIT
10.CHECK MOTOR HIGH-VOLTAGE CIRCUIT

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>Motor High-voltage Circuit

HINT:

If the "Motor High-voltage Circuit" inspection results are normal, perform the next step.


Result:
Proceed to
NEXT



NEXT