Home › Engine / Hybrid System › 2ZR-FXE (EMISSION CONTROL) › EGR COOLER › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _060064 2ZR-FXE EMISSION CONTROL _0294227 EGR COOLER A

2ZR-FXE EMISSION CONTROL  EGR COOLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR pipe with cooler sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


·

for Nickel Metal Hydride Battery:

(Click here)

·

for Lithium-ion Battery:

(Click here)


Replacement of ECM Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)
·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

PROCEDURE

Hide 16671 1.REMOVE FLOW SHUTTING VALVE (WATER VALVE)

Hide 16261 3.DISCONNECT WATER BY-PASS HOSE

a.
A377758

Slide the clip and disconnect the water by-pass hose from the EGR valve assembly.


Hide 87245A 4.DISCONNECT INLET HEATER WATER HOSE A

a.
A377707

Slide the clip and disconnect the inlet heater water hose A from the EGR pipe with cooler sub-assembly.


Hide 16281 5.DISCONNECT NO. 4 WATER BY-PASS HOSE

a.
A377709

Slide the clip and disconnect the No. 4 water by-pass hose from the EGR pipe with cooler sub-assembly.


Hide 25601L 6.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY

a.
A377699

Disconnect the EGR valve assembly connector.


b.
A377711

Remove the 2 nuts and disconnect the EGR pipe with cooler sub-assembly from the exhaust manifold (TWC: Front Catalyst).


c.
A377713C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and 2 nuts and disconnect the EGR pipe with cooler sub-assembly with the EGR valve assembly from the cylinder head sub-assembly and camshaft housing sub-assembly.


d.
A377714

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the cylinder head sub-assembly and camshaft housing sub-assembly.

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.



e.
A377759

Remove the EGR pipe with cooler sub-assembly with the EGR valve assembly.


f.
A377712

Remove the EGR cooler gasket from the EGR pipe with cooler sub-assembly.


g.
A377715

Slide the clip and disconnect the No. 6 water by-pass hose from the EGR pipe with cooler sub-assembly.


h.
A377717

Remove the 2 nuts and EGR pipe with cooler sub-assembly from the EGR valve assembly.


i.
A377704

Remove the EGR valve gasket from the EGR valve assembly.


j.
A379108

Using an E8 "TORX" socket wrench, remove the 3 stud bolts from the EGR pipe with cooler sub-assembly.

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.