Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2019.09
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300711 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1498  Communication Malfunction (A/C Inverter Local)  


DESCRIPTION

The hybrid vehicle control ECU and compressor with motor assembly communicate via direct line. Compressor control is stopped and this DTC is stored if communication information is cut off or abnormal information is received.

This DTC is also detected if high-voltage electricity supplied from the inverter with converter assembly to the compressor control circuit is shut off.

This DTC will be stored as a history DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1498 Communication Malfunction (A/C Inverter Local)
Any of the following conditions is met:
·

Error in communication line between the hybrid vehicle control ECU and compressor with motor assembly

·

Open in communication line between the hybrid vehicle control ECU and compressor with motor assembly

·

High-voltage power source shut off


·

Harness or connector between compressor with motor assembly and body ground

·

Harness or connector between hybrid vehicle control ECU and compressor with motor assembly, battery state sensor assembly

·

Hybrid vehicle control ECU

·

Compressor with motor assembly

·

HV air conditioning wire (harness or connector between compressor with motor assembly and inverter with converter assembly)

·

CAN communication system

·

Hybrid control system


Memorized

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (READY) ○ ○ ○
Malfunction Status Error in communication line between the hybrid vehicle control ECU and compressor with motor assembly ○ - -
Open in communication line between the hybrid vehicle control ECU and compressor with motor assembly - ○ -
High-voltage power source shut off - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

CAUTION:
·
A361801

When troubleshooting, use either a tool wrapped with vinyl insulation tape or an insulated tool. (It is extremely dangerous when a high-voltage charge passes through a non-insulated tool causing a short.)

·
A340358

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks.

·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C28
1.531,0.75 1.948,0.333 true 1.958,0.219 2.271,0.417 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

for 2ZR-FXE (for LITHIUM-ION BATTERY):

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.





NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs for both systems are output simultaneously.

·

Depending on the timing of the power supply to the 12 V power supply circuit and high-voltage circuit when the power switch is turned on (READY), an abnormal information signal may be output, causing this DTC to be stored. If the output DTC is a code that was memorized in the past, check the fuses and wire harnesses. If there is no malfunction, clear the DTC.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.CHECK FOR DTC

B

2.CHECK FOR DTC
a.

Check if hybrid control system DTCs are output.


Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTC P058A01 and P162B87 are output A
Both DTC P058A01 and P162B87 are not output B



A

3.CHECK FOR DTC

B

6.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND)
3.CHECK FOR DTC
a.

Disconnect the C20 battery state sensor assembly connector.


b.

Check if air conditioning system DTCs are output.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B1498 is output A
DTC B1498 is not output B



A

4.CHECK FOR DTC

B

4.CHECK FOR DTC
a.

Reconnect the C20 battery state sensor assembly connector.


b.

Disconnect the C13 compressor with motor assembly connector.


c.

Check if hybrid control system DTCs are output.


Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTC P058A01 and P162B87 are output A
Both DTC P058A01 and P162B87 are not output B



A

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY, BATTERY STATE SENSOR ASSEMBLY)

B

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY, BATTERY STATE SENSOR ASSEMBLY)
a.

Disconnect the A49 hybrid vehicle control ECU connector.


b.

Disconnect the C20 battery state sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-17 (LIN3) - C13-3 (DOUT) Always Below 1 Ω
A49-17 (LIN3) - C20-2 (LIN) Always Below 1 Ω
A49-17 (LIN3) or C13-3 (DOUT) - Body ground Always 10 kΩ or higher
A49-17 (LIN3) or C20-2 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (for M20A-FXS) A
OK (for 2ZR-FXE) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND)
CAUTION:

Do not disconnect the connector on the high-voltage side.


a.

Disconnect the C13 compressor with motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C13-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - IG CIRCUIT, GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - IG CIRCUIT, GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C13-1 (IG1) - C13-2 (GND) Power switch on (IG) 11 to 14 V
C13-1 (IG1) - C13-2 (GND) Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
a.

Disconnect the A49 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-17 (LIN3) - C13-3 (DOUT) Always Below 1 Ω
A49-17 (LIN3) or C13-3 (DOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT HV AIR CONDITIONING WIRE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT HV AIR CONDITIONING WIRE
CAUTION:
·
A340358

Be sure to wear insulated gloves.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U1-2 (PB) - U2-1 (ACPB) Always Below 1 Ω
U1-2 (PB) or U2-1 (ACPB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT HV AIR CONDITIONING WIRE

NG

11.INSPECT HV AIR CONDITIONING WIRE
10.INSPECT HV AIR CONDITIONING WIRE
CAUTION:
·
A340358

Be sure to wear insulated gloves.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U1-1 (PE) - U2-2 (ACPE) Always Below 1 Ω
U1-1 (PE) or U2-2 (ACPE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK A
NG (for M20A-FXS) B
NG (for 2ZR-FXE) C



A

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

B

C

11.INSPECT HV AIR CONDITIONING WIRE
CAUTION:
·
A340358

Be sure to wear insulated gloves.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U1-2 (PB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK A
NG (for M20A-FXS) B
NG (for 2ZR-FXE) C



A

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

B

C