Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY › 2019.09–2020.08
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0303873 KNEE AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  KNEE AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the lower No. 1 instrument panel airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55545 3.REMOVE FUSE BOX OPENING COVER

Hide 55470 4.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Hide 55434B 5.REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL

Hide 73900 6.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY WITH DOOR

CAUTION:
B417755C02
0.604,0.521 0.76,0.719 0.156,0.198 10 false .
V100155

Deployment Side


When storing the lower No. 1 instrument panel airbag assembly with door, keep the airbag deployment side facing upward.


a.

Check that the power switch off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B454046

Remove the 2 bolts.


d.

Disengage the hooks to separate the lower No. 1 instrument panel airbag assembly with door.

NOTICE:

When separating the lower No. 1 instrument panel airbag assembly with door, do not pull the airbag wire harness.



e.
B454047C01
0.406,2.313 0.719,2.208 true 0.604,3.094 0.99,2.469 true 1.51,1.167 1.167,0.917 true 0.188,2.229 0.5,2.385 0.313,0.156 10 false *a 0.427,3.021 0.74,3.177 0.313,0.156 10 false *b 1.542,1.094 1.854,1.25 0.313,0.156 10 false *c
*a Protective Tape
*b Airbag Connector
*c Airbag Connector Lock


Using a screwdriver with its tip wrapped in protective tape, release the airbag connector lock.


f.

Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly with door.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



Hide 73997 7.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG DOOR

a.
B460342

Disengage the hooks.


b.
B460341

Disengage the hooks to remove the lower No. 1 instrument panel airbag door from the lower No. 1 instrument panel airbag assembly.