Home › Drivetrain › P711 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID VEHICLE TRANSAXLE › from 2019.09
RM32K0E _52 Drivetrain _084042 P711 HYBRID TRANSMISSION / TRANSAXLE _0404750 HYBRID VEHICLE TRANSAXLE A

P711 HYBRID TRANSMISSION / TRANSAXLE  HYBRID VEHICLE TRANSAXLE  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 1.INSTALL UNION

HINT:

Perform this procedure only when replacement of the union or O-ring is necessary.


a.

Coat a new O-ring with ATF.


b.

Install the union and O-ring to the hybrid vehicle transaxle assembly.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 2.INSTALL STUD BOLT

a.
C412617

Clean and degrease the 2 stud bolt holes of the hybrid vehicle transaxle assembly.


b.
C412618C01
1.906,1.615 1.906,1.854 false 1.854,1.865 2.104,2.094 0.25,0.229 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the ends of the 2 stud bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper sealing of the 2 stud bolts, install them within 10 minutes of applying adhesive.



c.

Using a E8 "TORX" socket wrench, install the 2 stud bolts to the hybrid vehicle transaxle assembly.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 3.INSTALL TRANSAXLE HOUSING PLUG

a.

Install the transaxle housing plug and a new gasket to the hybrid vehicle transaxle assembly.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 2 wire harness clamp brackets to the hybrid vehicle transaxle assembly with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 33823 5.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the hybrid vehicle transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 44781E 6.INSTALL HOSE BRACKET

a.
C406264E01
1.219,1.052 1.375,1.25 0.156,0.198 10 true 1 2.396,1.229 2.552,1.427 0.156,0.198 10 true 2

Temporarily install the hose bracket to the hybrid vehicle transaxle assembly with the 2 bolts.


b.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


Hide 16575C 7.INSTALL NO. 1 WATER HOSE CLAMP BRACKET

a.

Install the No. 1 water hose clamp bracket to the hybrid vehicle transaxle assembly with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide G1251B 8.INSTALL NO. 1 MOTOR COOLING PIPE

a.

Temporarily install the No. 1 motor cooling pipe to the union with the flare nut.


b.

Install the No. 1 oil cooler tube clamp to the No. 1 transmission control cable bracket with the bolt.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


c.
C406267C01
2.729,1.656 3.042,1.813 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the flare nut to install the No. 1 motor cooling pipe.

Torque:
Specified Tightening Torque : 34.3 N*m (350 kgf*cm, 25 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

29.4 N*m (300 kgf*cm, 22 ft.*lbf)




Hide G125A 9.INSTALL MOTOR COOLING COOLER

a.
C406268E01
0.344,0.833 0.5,1.031 0.156,0.198 10 true 1 1.396,0.896 1.552,1.094 0.156,0.198 10 true 2 1.781,1.76 1.938,1.958 0.156,0.198 10 true 3

Temporarily install the motor cooling cooler with No. 2 motor cooling pipe to the hybrid vehicle transaxle assembly with the 3 bolts.


b.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


c.

Temporarily install the No. 2 motor cooling pipe to the hybrid vehicle transaxle assembly with the oil cooler union bolt and a new gasket.


d.

Install the No. 1 oil cooler tube clamp to the hose bracket with the bolt.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


e.

Tighten the oil cooler union bolt to install the No. 2 motor cooling pipe.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


f.
C406269C02
2.656,0.781 2.406,0.615 2.406,0.615 2.646,0.615 true 3.094,1.094 3.344,1.292 0.25,0.198 10 false *a 2.24,0.552 2.458,0.729 0.219,0.177 10 false *b
*a 2 to 7 mm (0.0787 to 0.276 in.)
*b Paint Mark


Connect the No. 1 motor cooling hose to the No. 1 motor cooling pipe and slide the clip to secure it.

NOTICE:

Make sure to align the paint mark on the No. 1 motor cooling pipe with the paint mark on the No. 1 motor cooling hose.



Hide 12364B 11.INSTALL NO. 2 ENGINE MOVING CONTROL ROD

a.
C406257C01
1.854,0.146 2.427,0.344 0.573,0.198 10 true 1 (*a), 6 2.583,1.167 2.76,1.354 0.177,0.188 10 true 5 1.927,1.74 2.104,1.927 0.177,0.188 10 true 2 0.948,0.875 1.125,1.063 0.177,0.188 10 true 3 1.219,0.448 1.396,0.635 0.177,0.188 10 true 4
*a Temporarily Tighten


Install the No. 2 engine moving control rod to the hybrid vehicle transaxle assembly with the 5 bolts in the order shown in the illustration.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 51201 12.TEMPORARILY INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Temporarily install the front suspension crossmember sub-assembly to the No. 2 engine moving control rod with the bolt.


Hide 13.INSTALL ENGINE ASSEMBLY

a.
C406270C01
0.219,0.76 0.385,0.948 0.167,0.188 10 true *1 2.531,0.229 2.698,0.417 0.167,0.188 10 true *1
*1 Knock Pin


Make sure that the knock pins are installed to the engine assembly.


b.
C379785N01
2.75,0.333 2.906,0.531 0.156,0.198 10 true A

Align the knock pins with the holes in the hybrid transaxle assembly and, while keeping the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly in close contact with one another, temporarily install the bolt (A).

NOTICE:
·

When tightening the bolts, be sure that the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly are in close contact with one another.

·

Do not apply grease to the inner splines of the transmission input damper assembly or input shaft assembly.

·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excessive force when installing the engine assembly.

·

Make sure to align the hybrid vehicle transaxle assembly so that the input shaft assembly of the hybrid vehicle transaxle assembly will be inserted straight into the inner splines of the transmission input damper assembly.

·

When inserting the input shaft assembly of the hybrid vehicle transaxle assembly into the inner splines of the transmission input damper assembly, do not shake the engine assembly.

·

When installing the engine assembly to the hybrid vehicle transaxle assembly, make sure to securely fit the knock pins into the knock pin holes.




c.
C379393N01
2.646,0.427 2.802,0.625 0.156,0.198 10 true A 1.854,0.063 2.01,0.26 0.156,0.198 10 false B 1.021,0.344 1.177,0.542 0.156,0.198 10 true C 2.365,1.958 2.552,2.135 0.188,0.177 10 true D 0.844,1.01 1,1.208 0.156,0.198 10 true C 1.073,1.833 1.229,2.031 0.156,0.198 10 true C 1.802,2.01 1.969,2.177 0.167,0.167 10 true C 2.615,1.75 2.771,1.948 0.156,0.198 10 true C

While keeping the contact surfaces of the engine assembly and hybrid vehicle transaxle assembly in close contact with one another, install the 8 bolts.

Bolt Bolt Length Torque
(A), (B) 50 mm (1.97 in.) 64 N*m (653 kgf*cm, 47 ft.*lbf)
(C) 45 mm (1.77 in.) 46 N*m (469 kgf*cm, 34 ft.*lbf)
(D) 35 mm (1.38 in.) 25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 14.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

a.
C411131C01
0.292,0.698 0.844,0.896 0.552,0.198 10 true 1 (*a), 3 2.635,0.563 2.792,0.771 0.156,0.208 10 true 2 0.75,0.094 0.896,0.281 0.146,0.188 10 true 4
*a Temporarily Tighten


Install the drive shaft heat insulator sub-assembly to the cylinder block sub-assembly with the 3 bolts in the order shown in the illustration.

Torque:
17.6 N*m (179 kgf*cm, 13 ft.*lbf)


Hide 11363A 16.INSTALL FLYWHEEL HOUSING SIDE COVER

a.

Install the flywheel housing side cover to the engine assembly.


Hide 28193 17.INSTALL STARTER HOLE INSULATOR

a.

Install the starter hole insulator to the engine assembly with the 2 bolts.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 821H2 18.INSTALL HV AIR CONDITIONING WIRE

a.
A407268C03
1.313,0.552 1.583,0.26 1.583,0.26 1.708,0.26 true 1.771,0.188 2.083,0.385 0.313,0.198 10 false *a
*a Green-colored Lock
V100137

Slide


Connect the connector and slide the green-colored lock as shown in the illustration to lock it securely.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Make sure that the connector is connected securely.



b.

Engage the clamp.


c.

Engage the guide to install the HV air conditioning wire to the hybrid vehicle transaxle assembly.


d.

Install the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 82121 19.CONNECT ENGINE WIRE

a.
C406279C02
2.813,1.74 3.042,1.927 0.229,0.188 10 true *1 1,1.729 1.219,1.906 0.219,0.177 10 true *2 2.49,0.219 2.688,0.396 0.198,0.177 10 true *3
*1 Resolver (Transmission Fluid Temperature Sensor) Connector
*2 Shift Lever Position Sensor Connector
*3 Generator Temperature Sensor Connector


Connect the generator temperature sensor connector.


b.

Confirm that no foreign matter or water has entered the connector of the shift lever position sensor and connect the connector.


c.

Connect the resolver (transmission fluid temperature sensor) connector.


d.

Install the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


e.

Engage the clamp.


f.

Engage the 5 clamps.


Hide 21.INSTALL SENSOR BRACKET

a.

Install the sensor bracket to the cylinder head sub-assembly with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 89481B 22.INSTALL DIFFERENTIAL PRESSURE SENSOR

a.

Install the differential pressure sensor to the sensor bracket with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the differential pressure sensor connector.


Hide 24.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 25. PERFORM RESOLVER LEARNING

NOTICE:

If the hybrid vehicle transaxle assembly has been replaced, make sure to perform resolver learning.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>UTILITY