Home › Drivetrain › P711 (HYBRID TRANSMISSION / TRANSAXLE) › OIL COOLER › from 2019.09
RM32K0E _52 Drivetrain _084042 P711 HYBRID TRANSMISSION / TRANSAXLE _0404754 OIL COOLER A

P711 HYBRID TRANSMISSION / TRANSAXLE  OIL COOLER  INSTALLATION  


PROCEDURE

Hide G1271C 1.INSTALL NO. 1 MOTOR COOLING HOSE

HINT:

Perform this procedure only when replacement of the motor cooling cooler is necessary.


a.
C403273C01
0,0 0,0 false
V100155

ATF Application Area


Coat a small amount of ATF as shown in the illustration.


b.
C403274C02
2.073,0.969 1.917,0.698 1.917,0.698 2.25,0.948 true 1.198,1.292 1.448,1.427 true 2.427,0.344 2.74,0.5 0.313,0.156 10 false *a 2.542,1.469 2.854,1.625 0.313,0.156 10 false *b 1.75,0.615 2.063,0.771 0.313,0.156 10 false *c 1.5,0.906 1.698,1.063 0.198,0.156 10 true *d 1.51,1.365 1.823,1.521 0.313,0.156 10 false *e
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d Center of Paint Mark
*e 180°
V100145

Claw of Clip Location


Install the No. 1 motor cooling hose to the motor cooling cooler and slide the clip to secure it.

NOTICE:
·

Be careful not to deform the motor cooling cooler.

·

Make sure to align the paint mark on the No. 1 motor cooling hose with the paint mark on the motor cooling cooler.

·

Make sure that the claws of the clip are positioned within the area shown in the illustration.




Hide G1272C 2.INSTALL NO. 2 MOTOR COOLING HOSE

HINT:

Perform this procedure only when replacement of the motor cooling cooler is necessary.


a.
C403275C01
0,0 0,0 false
V100155

ATF Application Area


Coat a small amount of ATF as shown in the illustration.


b.
C403276C02
2.083,0.958 1.938,0.625 1.938,0.625 2.24,0.958 true 1.208,1.271 1.417,1.396 true 2.427,0.344 2.74,0.5 0.313,0.156 10 false *a 2.521,1.479 2.833,1.635 0.313,0.156 10 false *b 1.76,0.531 2.073,0.688 0.313,0.156 10 false *c 1.479,0.906 1.688,1.042 0.208,0.135 10 true *d 1.458,1.344 1.771,1.5 0.313,0.156 10 false *e
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d Center of Paint Mark
*e 180°
V100145

Claw of Clip Location


Install the No. 2 motor cooling hose to the motor cooling cooler and slide the clip to secure it.

NOTICE:
·

Be careful not to deform the motor cooling cooler.

·

Make sure to align the paint mark on the No. 2 motor cooling hose with the paint mark on the motor cooling cooler.

·

Make sure that the claws of the clip are positioned within the area shown in the illustration.




Hide G125A 3.INSTALL MOTOR COOLING COOLER

a.
C403277N01
0.615,0.5 0.771,0.698 0.156,0.198 10 true 1 1.729,0.385 1.885,0.583 0.156,0.198 10 true 2 2.354,1.26 2.51,1.458 0.156,0.198 10 true 3

Temporarily install the motor cooling cooler to the hybrid vehicle transaxle assembly with the 3 bolts.


b.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


c.
C403278C01
2.583,1.063 2.25,0.958 2.25,0.958 2.583,0.958 true 3.042,1.354 3.354,1.51 0.313,0.156 10 false *a 2.094,0.885 2.406,1.042 0.313,0.156 10 false *b
*a 2 to 7 mm (0.0787 to 0.276 in.)
*b Paint Mark


Install the No. 2 motor cooling pipe to the No. 2 motor cooling hose and slide the clip to secure it.

NOTICE:

Make sure to align the paint mark on the No. 2 motor cooling pipe with the paint mark on the No. 2 motor cooling hose.



d.

Temporarily install the No. 2 motor cooling pipe to the hybrid vehicle transaxle assembly with the oil cooler union bolt and a new gasket.


e.

Install the No. 1 oil cooler tube clamp to the hose bracket with the bolt.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


f.

Tighten the oil cooler union bolt to install the No. 2 motor cooling pipe.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


g.
C406269C03
2.688,0.771 2.302,0.604 2.302,0.604 2.667,0.604 true 3.083,1.052 3.26,1.219 0.177,0.167 10 false *a 2.146,0.542 2.458,0.698 0.313,0.156 10 false *b
*a 2 to 7 mm (0.0787 to 0.276 in.)
*b Paint Mark


Connect the No. 1 motor cooling hose to the No. 1 motor cooling pipe and slide the clip to secure it.

NOTICE:

Make sure to align the paint mark on the No. 1 motor cooling pipe with the paint mark on the No. 1 motor cooling hose.



Hide G922F 4.CONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

Hide G922H 5.CONNECT INLET HYBRID RADIATOR HOSE

Hide 8.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 51444A 9.INSTALL REAR ENGINE UNDER COVER LH

Hide 51410 10.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY