Home › Drivetrain › P711 (HYBRID TRANSMISSION / TRANSAXLE) › INPUT SHAFT OIL SEAL › 2019.09–2020.08
RM32K0E _52 Drivetrain _084042 P711 HYBRID TRANSMISSION / TRANSAXLE _0404756 INPUT SHAFT OIL SEAL A

P711 HYBRID TRANSMISSION / TRANSAXLE  INPUT SHAFT OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during input shaft type T oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: If the vehicle height has changed due to suspension or tire replacement.

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Initialize back door lock Power Door Lock Control System (Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:
(Click here)
for Calibration:
(Click here)
Suspension, tires, etc.*2
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.

·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.



PROCEDURE

Hide 30900 1.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 35710A 2.REMOVE INPUT SHAFT TYPE T OIL SEAL

a.
C377405C02
1.188,0.344 1.479,0.344 1.479,0.344 1.844,1 true 1.021,0.25 1.302,0.458 0.281,0.208 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the input shaft type T oil seal from the hybrid vehicle transaxle assembly.

NOTICE:

Be careful not to damage the input shaft assembly or hybrid vehicle transaxle assembly.



Hide 35710A 3.INSTALL INPUT SHAFT TYPE T OIL SEAL

a.

Coat the lip of a new input shaft type T oil seal with a small amount of MP grease.


b.
C377942C01
1.99,1.969 2.365,3.021 2.365,3.021 2.521,3.021 true 1.385,0.115 1.667,0.333 0.281,0.219 10 false *a 2.563,2.927 3.021,3.125 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, install the input shaft type T oil seal to the hybrid vehicle transaxle assembly.

SST
09608-04031  

Standard Depth:

1.9 to 2.7 mm (0.0748 to 0.106 in.)


NOTICE:
·

Do not allow foreign matter to attach to the lip of the input shaft type T oil seal.

·

Do not install the input shaft type T oil seal at an angle.




Hide 30900 4.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY