Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2019.09
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1214  Hydraulic Control System Malfunction  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) controls braking force according to the hybrid control system regenerative braking force and provides the hydraulic pressure necessary for operating the master cylinder and each wheel cylinder according to the servo pressure sensor.

DTCs may be stored if one of the following occurs:

·

Brake fluid leaks.

·

Wheel cylinder vibrates due to uneven wear of a brake disc.

·

Foreign matter enters a solenoid valve.

·

Line pressure drops during air bleeding.

·

Brake pads are replaced.

·

Rotors are replaced.

HINT:

When replacing the brake pads, retracting the brake caliper pistons and installing new brake pads will greatly increase the clearance between the brake pads and brake discs. This will result in a significant possibility of this DTC being stored the next time the brake pedal is depressed. As this is not a malfunction, clear the DTC if it is stored for this reason.



DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1214 Hydraulic Control System Malfunction 431
432
436
438
439
440
441
442
·

INF Code: 431

-

Fluid pressure control performance degraded (high pressure).


·

INF Code: 432

-

Fluid pressure control performance degraded (low pressure).


·

INF Code: 436

-

SLA valve malfunction (stuck, etc.).


·

INF Code: 438

-

Malfunction in one of the two circuits (leakage, etc.).


·

INF Code: 439

-

Valve malfunction (stuck, etc.).


·

INF Code: 440

-

SSA valve malfunction (stuck, etc.).


·

INF Code: 441

-

SGH valve malfunction (stuck, etc.).


·

INF Code: 442

-

Malfunction (leakage, etc.) detected in the ABS decrease pressure valve in the brake actuator assembly.



·

INF Code: 431, 432, 436, 438, 439, 440, 441

-

Brake fluid leaks

-

Uneven brake disc rotor wear

-

Brake actuator (brake booster with master cylinder assembly)


·

INF Code: 442

-

Brake actuator assembly



Electronically controlled brake system DTC

CAUTION / NOTICE / HINT

NOTICE:

After replacing the brake booster with master cylinder assembly or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS (CHECK CONDITION WHEN MALFUNCTION OCCURRED) AND FREEZE FRAME DATA
a.

Interview the customer to check the vehicle conditions when the brake warning light / yellow (minor malfunction) illuminated.


b.

Using the GTS, read the "Shift Lever Position", "Vehicle Speed", "Yaw Rate Sensor", "Steering Angle Sensor", "Reaction Force Pressure", "Servo Pressure" and "Accumulator Pressure" of the Freeze Frame Data stored when the DTC was stored.

Also, read the Freeze Frame Data stored when the DTC was stored and make a note of the INF codes.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>FREEZE FRAME DATA

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
NOTICE:

Make sure to make a note of the INF codes as they are used in a following step.


HINT:
·

Freeze Frame Data is only stored once when a DTC is stored.

·

If other DTCs are output, repair any malfunctions related to those DTCs first, and then reproduce the conditions that caused DTC C1214 to be stored based on the interview with the customer.




Result:
Proceed to
NEXT



NEXT

2.CHECK FOR FLUID LEAK
2.CHECK FOR FLUID LEAK
a.

Check that there are no fluid leaks in the brake lines between the brake booster with master cylinder assembly and the wheel cylinders.


b.

Check that there is no brake fluid leaks from the brake booster with master cylinder assembly or brake actuator assembly body.


c.

Check that the brakes are not dragging.

OK:

There are no fluid leaks or dragging.



Result:
Proceed to
OK
NG



OK

3.PERFORM AIR BLEEDING

NG

REPAIR OR REPLACE APPLICABLE PART

3.PERFORM AIR BLEEDING
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Perform the air bleeding procedure in Bleed Brake System.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


Result:
Proceed to
NEXT



NEXT

4.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE ACTUATOR ASSEMBLY (ACTUATOR SIDE)
4.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY AND BRAKE ACTUATOR ASSEMBLY (ACTUATOR SIDE)
a.

Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector 2 minutes after the power switch is turned off.


d.

Disconnect the A85 brake actuator assembly connector (for LHD).


e.

Disconnect the A84 brake actuator assembly connector (for RHD).


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Result:
Result Proceed to
OK A
NG (skid control ECU (brake booster with master cylinder assembly)) (for LHD) B
NG (skid control ECU (brake booster with master cylinder assembly)) (for RHD) C
NG(brake actuator assembly) (for LHD) D
NG(brake actuator assembly) (for RHD) E



A

5.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

D

E

5.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)
a.

Reconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the A85 brake actuator assembly connector (for LHD).


c.

Reconnect the A84 brake actuator assembly connector (for RHD).


d.

Measure the voltage and resistance on the wire harness side.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU

OK:

Voltage and resistance readings are all normal.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A85 brake actuator assembly connector (for LHD).


e.

Disconnect the A84 brake actuator assembly connector (for RHD).


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A39-14 (+BS) - A85-5 (+BS) Always Below 1 Ω
A39-14 (+BS) or A85-5 (+BS) - Body ground Always 10 kΩ or higher
A39-48 (SFRH) - A85-31 (SFRH) Always Below 1 Ω
A39-48 (SFRH) or A85-31 (SFRH) - Body ground Always 10 kΩ or higher
A39-49 (SFLH) - A85-28 (SFLH) Always Below 1 Ω
A39-49 (SFLH) or A85-28 (SFLH) - Body ground Always 10 kΩ or higher
A39-50 (SRRH) - A85-29 (SRRH) Always Below 1 Ω
A39-50 (SRRH) or A85-29 (SRRH) - Body ground Always 10 kΩ or higher
A39-51 (SRLH) - A85-30 (SRLH) Always Below 1 Ω
A39-51 (SRLH) or A85-30 (SRLH) - Body ground Always 10 kΩ or higher
A39-44 (SFRR) - A85-15 (SFRR) Always Below 1 Ω
A39-44 (SFRR) or A85-15 (SFRR) - Body ground Always 10 kΩ or higher
A39-45 (SFLR) - A85-18 (SFLR) Always Below 1 Ω
A39-45 (SFLR) or A85-18 (SFLR) - Body ground Always 10 kΩ or higher
A39-46 (SRRR) - A85-17 (SRRR) Always Below 1 Ω
A39-46 (SRRR) or A85-17 (SRRR) - Body ground Always 10 kΩ or higher
A39-47 (SRLR) - A85-16 (SRLR) Always Below 1 Ω
A39-47 (SRLR) or A85-16 (SRLR) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A39-14 (+BS) - A84-5 (+BS) Always Below 1 Ω
A39-14 (+BS) or A84-5 (+BS) - Body ground Always 10 kΩ or higher
A39-48 (SFRH) - A84-28 (SFRH) Always Below 1 Ω
A39-48 (SFRH) or A84-28 (SFRH) - Body ground Always 10 kΩ or higher
A39-49 (SFLH) - A84-31 (SFLH) Always Below 1 Ω
A39-49 (SFLH) or A84-31 (SFLH) - Body ground Always 10 kΩ or higher
A39-50 (SRRH) - A84-30 (SRRH) Always Below 1 Ω
A39-50 (SRRH) or A84-30 (SRRH) - Body ground Always 10 kΩ or higher
A39-51 (SRLH) - A84-29 (SRLH) Always Below 1 Ω
A39-51 (SRLH) or A84-29 (SRLH) - Body ground Always 10 kΩ or higher
A39-44 (SFRR) - A84-18 (SFRR) Always Below 1 Ω
A39-44 (SFRR) or A84-18 (SFRR) - Body ground Always 10 kΩ or higher
A39-45 (SFLR) - A84-15 (SFLR) Always Below 1 Ω
A39-45 (SFLR) or A84-15 (SFLR) - Body ground Always 10 kΩ or higher
A39-46 (SRRR) - A84-16 (SRRR) Always Below 1 Ω
A39-46 (SRRR) or A84-16 (SRRR) - Body ground Always 10 kΩ or higher
A39-47 (SRLR) - A84-17 (SRLR) Always Below 1 Ω
A39-47 (SRLR) or A84-17 (SRLR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK INFORMATION CODE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INFORMATION CODE
a.

Reconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the A85 brake actuator assembly connector (for LHD).


c.

Reconnect the A84 brake actuator assembly connector (for RHD).


d.

Reconfirm the INF codes noted in step 1.


Result:
Result Proceed to
INF codes 431, 432 and/or 436 were output in step 1. A
INF code 438 was output in step 1. B
INF codes 440 and/or 441 were output in step 1. C
INF code 442 was output in step 1. D



A

8.READ VALUE USING GTS (SERVO PRESSURE)

B

11.READ VALUE USING GTS (SERVO PRESSURE)

C

15.RECONFIRM DTC

D

16.INSPECT BRAKE PEDAL STROKE SENSOR ASSEMBLY OUTPUT VOLTAGES AND WHEEL CYLINDER PRESSURE
8.READ VALUE USING GTS (SERVO PRESSURE)
a.

Connect an LSPV gauge set.


b.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 to 2.10 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > ABS/VSC/TRC > Data List
Tester Display
Servo Pressure
50003 105 501

c.

Depress the brake pedal slowly and check the servo pressure output values with respect to the wheel cylinder pressure values for each wheel.

Standard Pressure*1:
Servo Pressure (for Front Right Wheel)
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
Servo Pressure
[MPa]
2.0 (20.4, 290) 0.3 to 4.3
5.0 (51.0, 725) 3.3 to 7.3
7.0 (71.4, 1015) 5.3 to 9.3

Servo Pressure (for Front Left Wheel)
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
Servo Pressure
[MPa]
2.0 (20.4, 290) 0.3 to 4.3
5.0 (51.0, 725) 3.3 to 7.3
7.0 (71.4, 1015) 5.3 to 9.3


Standard Pressure*2:
Servo Pressure (for Front Right Wheel)
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
Servo Pressure
[MPa]
2.0 (20.4, 290) 0.3 to 4.3
5.0 (51.0, 725) 3.3 to 7.3
7.0 (71.4, 1015) 5.3 to 9.3

Servo Pressure (for Front Left Wheel)
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
Servo Pressure
[MPa]
2.0 (20.4, 290) 0.3 to 4.3
5.0 (51.0, 725) 3.3 to 7.3
7.0 (71.4, 1015) 5.3 to 9.3


*1: for TMMT Made

*2: for TMC Made



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

9.CHECK BRAKE DISC

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

9.CHECK BRAKE DISC
a.

Turn the power switch off.


b.

Disconnect the A44 brake pedal stroke sensor assembly connector.


c.

Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.

OK:

Brake pedal does not vibrate during braking.


HINT:
·

An unevenly worn disc may vibrate the caliper piston and cause fluctuations in brake line pressure, triggering a malfunction detection condition.

·

The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.

·

If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.

·

The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.

·

for TMC Made

Uneven disc wear can be checked by measuring the disc thickness variation.

for Front Brake: Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for TMC Made)>INSPECTION

for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMC Made)>INSPECTION

·

for TMMT Made

Uneven disc wear can be checked by measuring the disc thickness variation.

for Front Brake: Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for TMMT Made)>INSPECTION

for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMMT Made)>INSPECTION




Result:
Proceed to
OK
NG



OK

10.RECONFIRM DTC

NG

REPLACE BRAKE DISC

10.RECONFIRM DTC
a.

Turn the power switch off.


b.

Reconnect the A44 brake pedal stroke sensor assembly connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


e.

Turn the power switch off and wait for 2 minutes or more.


f.

Turn the power switch on (IG).


g.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1214 is not output. A
DTC C1214 is output. (for LHD) B
DTC C1214 is output. (for RHD) C


HINT:

If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

11.READ VALUE USING GTS (SERVO PRESSURE)
a.

Connect an LSPV gauge set.


b.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Servo Pressure Pressure value of servo Min.: 0.00 MPa, Max.: 24.48 MPa Brake pedal released: 0.00 to 2.10 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > ABS/VSC/TRC > Data List
Tester Display
Servo Pressure
50003 105 501

c.

Depress the brake pedal slowly and check the servo pressure output values with respect to the wheel cylinder pressure values for each wheel.

Standard Pressure*1:
Servo Pressure (for Front Right Wheel)
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
Servo Pressure
[MPa]
2.0 (20.4, 290) 0.3 to 4.3
5.0 (51.0, 725) 3.3 to 7.3
7.0 (71.4, 1015) 5.3 to 9.3

Servo Pressure (for Front Left Wheel)
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
Servo Pressure
[MPa]
2.0 (20.4, 290) 0.3 to 4.3
5.0 (51.0, 725) 3.3 to 7.3
7.0 (71.4, 1015) 5.3 to 9.3


Standard Pressure*2:
Servo Pressure (for Front Right Wheel)
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
Servo Pressure
[MPa]
2.0 (20.4, 290) 0.3 to 4.3
5.0 (51.0, 725) 3.3 to 7.3
7.0 (71.4, 1015) 5.3 to 9.3

Servo Pressure (for Front Left Wheel)
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
Servo Pressure
[MPa]
2.0 (20.4, 290) 0.3 to 4.3
5.0 (51.0, 725) 3.3 to 7.3
7.0 (71.4, 1015) 5.3 to 9.3


*1: for TMMT Made

*2: for TMC Made



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

12.CHECK BRAKE DISC

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

12.CHECK BRAKE DISC
a.

Turn the power switch off.


b.

Disconnect the A44 brake pedal stroke sensor assembly connector.


c.

Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.

OK:

Brake pedal does not vibrate during braking.


HINT:
·

An unevenly worn disc may vibrate the caliper piston and cause fluctuations in brake line pressure, triggering a malfunction detection condition.

·

The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.

·

If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.

·

The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.

·

for TMC Made

Uneven disc wear can be checked by measuring the disc thickness variation.

for Front Brake: Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for TMC Made)>INSPECTION

for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMC Made)>INSPECTION

·

for TMMT Made

Uneven disc wear can be checked by measuring the disc thickness variation.

for Front Brake: Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for TMMT Made)>INSPECTION

for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMMT Made)>INSPECTION




Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (STROKE SENSOR AND STROKE SENSOR2)

NG

REPLACE BRAKE DISC

13.READ VALUE USING GTS (STROKE SENSOR AND STROKE SENSOR2)
a.

Turn the power switch off.


b.

Reconnect the A44 brake pedal stroke sensor assembly connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the power switch off.


e.

Mount a pedal effort gauge.


f.

Turn the power switch on (READY) and depress the brake pedal once.

HINT:

Depress the brake pedal after turning the power switch on (READY) to set the vehicle to linear mode (switching solenoid (SSA) on).



g.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor assembly Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Stroke Sensor2 Brake pedal stroke sensor assembly 2 Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 105 11,12

h.

Depress the brake pedal slowly and check the brake pedal stroke sensor assembly output voltages with respect to brake pedal depression force.

NOTICE:

Perform this procedure in linear mode (switching solenoid (SSA) on).


Standard Pressure*1:
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Stroke Sensor2
[V]
50 (5, 11.2) 1.05 to 1.75 3.25 to 3.95
100 (10, 22.5) 1.18 to 1.88 3.12 to 3.82
150 (15, 33.7) 1.28 to 1.98 3.02 to 3.72
200 (20, 45.0) 1.34 to 2.04 2.96 to 3.66


Standard Pressure*2:
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Stroke Sensor2
[V]
50 (5, 11.2) 1.03 to 1.73 3.27 to 3.97
100 (10, 22.5) 1.15 to 1.85 3.15 to 3.85
150 (15, 33.7) 1.23 to 1.93 3.07 to 3.77
200 (20, 45.0) 1.28 to 1.98 3.02 to 3.72


*1: for TMMT Made

*2: for TMC Made



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

14.RECONFIRM DTC

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

14.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


c.

Turn the power switch off and wait for 2 minutes or more.


d.

Turn the power switch on (IG).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1214 is not output. A
DTC C1214 is output. (for LHD) B
DTC C1214 is output. (for RHD) C


HINT:

If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

15.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


c.

Turn the power switch off and wait for 2 minutes or more.


d.

Turn the power switch on (IG).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1214 is not output. A
DTC C1214 is output. (for LHD) B
DTC C1214 is output. (for RHD) C


HINT:

If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

16.INSPECT BRAKE PEDAL STROKE SENSOR ASSEMBLY OUTPUT VOLTAGES AND WHEEL CYLINDER PRESSURE
a.

Mount a pedal effort gauge.


b.

Disconnect the A12 brake booster pump assembly connector.


c.

Depress the brake pedal 10 times or more until it becomes hard.

HINT:

Depressing the brake pedal with the connector of the brake booster pump assembly disconnected drops the accumulator pressure to approximately 0 MPa.



d.

Connect an LSPV gauge set.


e.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor assembly Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
50003 105 11

f.

Slowly depress the brake pedal and check the brake pedal stroke sensor assembly output voltages and the wheel cylinder pressure with respect to brake pedal depression force.

NOTICE:

Check the wheel cylinder pressure with the switching solenoid (SSA, SGH) off and an accumulator pressure of 0 MPa.


Standard Pressure*1:
for Front Right Wheel
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
200 (20, 45.0) 1.14 to 1.84 0.03 (0.3, 4.4) to 2.03 (20.7, 294)
500 (51, 112.4) 1.31 to 2.01 2.00 (20.4, 290) to 4.00 (40.8, 580)

for Front Left Wheel
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
200 (20, 45.0) 1.14 to 1.84 0.03 (0.3, 4.4) to 2.03 (20.7, 294)
500 (51, 112.4) 1.31 to 2.01 2.00 (20.4, 290) to 4.00 (40.8, 580)


Standard Pressure*2:
for Front Right Wheel
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
200 (20, 45.0) 1.09 to 1.79 0.04 (0.4, 6.0) to 2.03 (20.7, 294)
500 (51, 112.4) 1.24 to 1.94 2.07 (21.1, 300) to 4.07 (41.5, 590)

for Front Left Wheel
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
Hydraulic Pressure
[MPa (kgf/cm2, psi)]
200 (20, 45.0) 1.09 to 1.79 0.04 (0.4, 6.0) to 2.03 (20.7, 294)
500 (51, 112.4) 1.24 to 1.94 2.07 (21.1, 300) to 4.07 (41.5, 590)


*1: for TMMT Made

*2: for TMC Made



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

17.RECONFIRM DTC

B

C

17.RECONFIRM DTC
a.

Turn the power switch off.


b.

Reconnect the A12 brake booster pump assembly connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


e.

Turn the power switch off and wait for 2 minutes or more.


f.

Turn the power switch on (IG).


g.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1214 is not output. A
DTC C1214 is output. (for LHD) B
DTC C1214 is output. (for RHD) C


HINT:

If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE




A

B

C