There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| No resistance exists between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3. | ·
Short to +B in CAN main bus line ·
Short to +B in CAN branch line ·
Central gateway ECU (network gateway ECU) ·
Millimeter wave radar sensor assembly (w/ Toyota Safety Sense) ·
Forward recognition camera (w/ Toyota Safety Sense) ·
Clearance warning ECU assembly (w/ TOYOTA Parking Assist-sensor System) ·
Parking assist ECU (w/ Panoramic View Monitor System) ·
Blind spot monitor sensor LH (w/ Blind Spot Monitor System) ·
No. 1 CAN junction connector ·
No. 6 CAN junction connector (w/ Blind Spot Monitor System) |
w/o Blind Spot Monitor System
w/ Blind Spot Monitor System
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the LDA main switch on and then drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 52 seconds or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Check vehicle type.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/o Blind Spot Monitor System | A |
| w/ Blind Spot Monitor System | B |
A
B
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System) |
| *c | to Forward Recognition Camera
(w/ Toyota Safety Sense) |
*d | to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense) |
| *e | to Central Gateway ECU (NetworkGateway ECU) | - | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F111-1 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Clearance warning ECU assembly*1 |
| F111-11 (CANL) - F144-16 (BAT) | |||
| F111-2 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Forward recognition camera*2 |
| F111-12 (CANL) - F144-16 (BAT) | |||
| F111-3 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Millimeter wave radar sensor assembly*2 |
| F111-13 (CANL) - F144-16 (BAT) | |||
| F111-9 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| F111-19 (CANL) - F144-16 (BAT) | |||
| F111-10 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| F111-20 (CANL) - F144-16 (BAT) |
*1: w/ TOYOTA Parking Assist-sensor System
*2: w/ Toyota Safety Sense
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to ECU or sensor) | C |
A
B
C
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F111-9 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F111-19 (CANL) - F144-16 (BAT) | ||
| F111-10 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F111-20 (CANL) - F144-16 (BAT) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the No. 6 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to Blind Spot Monitor Sensor LH |
| *c | to Central Gateway ECU (Network Gateway ECU) | *d | to No. 1 CAN Junction Connector |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| M104-9 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Blind spot monitor sensor LH |
| M104-20 (CANL) - F144-16 (BAT) | |||
| M104-10 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| M104-21 (CANL) - F144-16 (BAT) | |||
| M104-11 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 1 CAN junction connector |
| M104-22 (CANL) - F144-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 1 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M104-10 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M104-21 (CANL) - F144-16 (BAT) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System) |
| *c | to Forward Recognition Camera
(w/ Toyota Safety Sense) |
*d | to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense) |
| *e | to No. 6 CAN Junction Connector | *f | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F111-1 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Clearance warning ECU assembly*1 |
| F111-11 (CANL) - F144-16 (BAT) | |||
| F111-2 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Forward recognition camera*2 |
| F111-12 (CANL) - F144-16 (BAT) | |||
| F111-3 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Millimeter wave radar sensor assembly*2 |
| F111-13 (CANL) - F144-16 (BAT) | |||
| F111-9 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 6 CAN junction connector |
| F111-19 (CANL) - F144-16 (BAT) | |||
| F111-10 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| F111-20 (CANL) - F144-16 (BAT) |
*1: w/ TOYOTA Parking Assist-sensor System
*2: w/ Toyota Safety Sense
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 6 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F111-10 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F111-20 (CANL) - F144-16 (BAT) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F74-23 (CA1H) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F74-8 (CA1L) - F144-16 (BAT) |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.
| Result |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/o Blind Spot Monitor System | A |
| w/ Blind Spot Monitor System | B |
A
B
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System) |
| *c | to Forward Recognition Camera
(w/ Toyota Safety Sense) |
*d | to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense) |
| *e | to Central Gateway ECU (NetworkGateway ECU) | - | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F164-1 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Clearance warning ECU assembly*1 |
| F164-7 (CANL) - F144-16 (BAT) | |||
| F164-2 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Forward recognition camera*2 |
| F164-8 (CANL) - F144-16 (BAT) | |||
| F164-3 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Millimeter wave radar sensor assembly*2 |
| F164-9 (CANL) - F144-16 (BAT) | |||
| F164-5 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| F164-11 (CANL) - F144-16 (BAT) | |||
| F164-6 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| F164-11 (CANL) - F144-16 (BAT) |
*1: w/ TOYOTA Parking Assist-sensor System
*2: w/ Toyota Safety Sense
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to ECU or sensor) | C |
A
B
C
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F164-5 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F164-11 (CANL) - F144-16 (BAT) | ||
| F164-6 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F164-12 (CANL) - F144-16 (BAT) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the No. 6 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) (for TMC Made) |
| *c | to Blind Spot Monitor Sensor LH | *d | to Central Gateway ECU (Network Gateway ECU) (for TMMT Made) |
| *e | to No. 1 CAN Junction Connector | - | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| M104-8 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| M104-19 (CANL) - F144-16 (BAT) | |||
| M104-9 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Blind spot monitor sensor LH |
| M104-20 (CANL) - F144-16 (BAT) | |||
| M104-11 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 1 CAN junction connector |
| M104-22 (CANL) - F144-16 (BAT) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| M104-9 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Blind spot monitor sensor LH |
| M104-20 (CANL) - F144-16 (BAT) | |||
| M104-10 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| M104-21 (CANL) - F144-16 (BAT) | |||
| M104-11 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 1 CAN junction connector |
| M104-22 (CANL) - F144-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 1 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) (for TMC Made) |
| *c | to Central Gateway ECU (Network Gateway ECU) (for TMMT Made) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M104-8 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M104-19 (CANL) - F144-16 (BAT) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M104-10 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M104-21 (CANL) - F144-16 (BAT) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System) |
| *c | to Forward Recognition Camera
(w/ Toyota Safety Sense) |
*d | to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense) |
| *e | to Parking Assist ECU
(w/ Panoramic View Monitor System) |
*f | to No. 6 CAN Junction Connector |
| *g | to Central Gateway ECU (Network Gateway ECU) | - | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F164-1 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Clearance warning ECU assembly*1 |
| F164-7 (CANL) - F144-16 (BAT) | |||
| F164-2 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Forward recognition camera*2 |
| F164-8 (CANL) - F144-16 (BAT) | |||
| F164-3 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Millimeter wave radar sensor assembly*2 |
| F164-9 (CANL) - F144-16 (BAT) | |||
| F164-4 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Parking assist ECU*3 |
| F164-10 (CANL) - F144-16 (BAT) | |||
| F164-5 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | No. 6 CAN junction connector |
| F164-11 (CANL) - F144-16 (BAT) | |||
| F164-6 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| F164-12 (CANL) - F144-16 (BAT) |
*1: w/ TOYOTA Parking Assist-sensor System
*2: w/ Toyota Safety Sense
*3: w/ Panoramic View Monitor System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to No. 6 CAN junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F164-6 (CANH) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F164-12 (CANL) - F144-16 (BAT) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F74-23 (CA1H) - F144-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| F74-8 (CA1L) - F144-16 (BAT) |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.
| Result |
|---|
| OK |
| NG |
OK
NG