Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2019.09–2020.08
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 1 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Millimeter wave radar sensor assembly

(w/ Toyota Safety Sense)

·

Forward recognition camera

(w/ Toyota Safety Sense)

·

Clearance warning ECU assembly

(w/ TOYOTA Parking Assist-sensor System)

·

Parking assist ECU

(w/ Panoramic View Monitor System)

·

Blind spot monitor sensor LH

(w/ Blind Spot Monitor System)

·

No. 1 CAN junction connector

·

No. 6 CAN junction connector

(w/ Blind Spot Monitor System)



WIRING DIAGRAM

w/o Blind Spot Monitor System


C360936E12
0.677,0.979 1.448,1.177 0.771,0.198 10 false 120 Ω 0.677,5.271 1.448,5.469 0.771,0.198 10 false 120 Ω 1.375,0.625 2.146,0.823 0.771,0.198 10 false CA1H 1.354,1.156 2.125,1.354 0.771,0.198 10 false CA1L 1.354,4.906 2.125,5.104 0.771,0.198 10 false CAXH 1.354,5.438 2.125,5.635 0.771,0.198 10 false CAXL 1.854,0.615 2.125,0.813 0.271,0.198 10 false 23 1.854,1.156 2.125,1.354 0.271,0.198 10 false 8 1.854,4.906 2.125,5.104 0.271,0.198 10 false 9 1.854,5.448 2.125,5.646 0.271,0.198 10 false 24 2.813,5.448 3.083,5.646 0.271,0.198 10 false 20 2.813,4.906 3.083,5.104 0.271,0.198 10 false 10 2.802,1.156 3.073,1.354 0.271,0.198 10 false 19 2.875,0.615 3.146,0.813 0.271,0.198 10 false 9 4.188,0.615 4.458,0.813 0.271,0.198 10 false 3 4.198,1.156 4.469,1.354 0.271,0.198 10 false 13 5.219,0.615 5.49,0.813 0.271,0.198 10 false 3 5.219,1.156 5.49,1.354 0.271,0.198 10 false 2 5.448,0.708 6.219,0.906 0.771,0.198 10 false CA2H 5.448,1.24 6.219,1.438 0.771,0.198 10 false CA2L 5.188,1.802 6.688,2.344 1.5,0.542 10 false Millimeter Wave Radar Sensor Assembly*1 5.188,1.635 5.958,1.833 0.771,0.198 10 false A2 4.188,2.76 4.458,2.958 0.271,0.198 10 false 2 4.177,3.292 4.448,3.49 0.271,0.198 10 false 12 4.188,4.906 4.458,5.104 0.271,0.198 10 false 1 4.188,5.438 4.458,5.635 0.271,0.198 10 false 11 5.219,2.76 5.49,2.958 0.271,0.198 10 false 5 5.146,3.292 5.417,3.49 0.271,0.198 10 false 11 5.146,5.438 5.417,5.635 0.271,0.198 10 false 18 5.146,4.906 5.417,5.104 0.271,0.198 10 false 17 5.448,2.865 6.219,3.063 0.771,0.198 10 false CA1P 5.448,3.396 6.219,3.594 0.771,0.198 10 false CA1N 5.448,5 6.219,5.198 0.771,0.198 10 false R1 5.448,5.542 6.219,5.74 0.771,0.198 10 false R2 5.271,3.938 6.583,4.5 1.313,0.563 10 false Forward Recognition Camera*1 5.271,3.781 6.042,3.979 0.771,0.198 10 false R5 5.313,6.083 6.552,6.698 1.24,0.615 10 false Clearance Warning ECU Assembly*2 5.313,5.927 6.083,6.125 0.771,0.198 10 false F142 2.594,5.896 3.365,6.094 0.771,0.198 10 false F111 2.594,6.063 4.625,6.698 2.031,0.635 10 false No. 1 CAN Junction Connector 0.188,6.083 2.167,6.479 1.979,0.396 10 false Central Gateway ECU (Network Gateway ECU) 0.188,5.917 0.958,6.115 0.771,0.198 10 false F74 0.177,6.917 4.156,7.115 3.979,0.198 10 false *1: w/ Toyota Safety Sense 0.177,7.25 4.156,7.448 3.979,0.198 10 false *2: w/ TOYOTA Parking Assist-sensor System 0.073,0.042 1.542,0.281 1.469,0.24 12 false for LHD:

C360936E13
0.677,0.979 1.448,1.177 0.771,0.198 10 false 120 Ω 0.677,5.271 1.448,5.469 0.771,0.198 10 false 120 Ω 1.354,0.615 2.125,0.813 0.771,0.198 10 false CA1H 1.354,1.156 2.125,1.354 0.771,0.198 10 false CA1L 1.354,4.906 2.125,5.104 0.771,0.198 10 false CAXH 1.354,5.438 2.125,5.635 0.771,0.198 10 false CAXL 1.854,0.615 2.125,0.813 0.271,0.198 10 false 23 1.854,1.156 2.125,1.354 0.271,0.198 10 false 8 1.854,4.906 2.125,5.104 0.271,0.198 10 false 9 1.854,5.448 2.125,5.646 0.271,0.198 10 false 24 2.813,5.448 3.083,5.646 0.271,0.198 10 false 11 2.875,4.906 3.146,5.104 0.271,0.198 10 false 5 2.802,1.156 3.073,1.354 0.271,0.198 10 false 12 2.875,0.615 3.146,0.813 0.271,0.198 10 false 6 4.188,0.615 4.458,0.813 0.271,0.198 10 false 3 4.198,1.156 4.469,1.354 0.271,0.198 10 false 9 5.219,0.615 5.49,0.813 0.271,0.198 10 false 3 5.219,1.156 5.49,1.354 0.271,0.198 10 false 2 5.448,0.708 6.219,0.906 0.771,0.198 10 false CA2H 5.448,1.24 6.219,1.438 0.771,0.198 10 false CA2L 5.188,1.802 6.688,2.344 1.5,0.542 10 false Millimeter Wave Radar Sensor Assembly*1 5.188,1.635 5.958,1.833 0.771,0.198 10 false A2 4.188,2.76 4.458,2.958 0.271,0.198 10 false 2 4.177,3.292 4.448,3.49 0.271,0.198 10 false 8 4.188,4.906 4.458,5.104 0.271,0.198 10 false 1 4.188,5.438 4.458,5.635 0.271,0.198 10 false 7 5.219,2.76 5.49,2.958 0.271,0.198 10 false 5 5.146,3.292 5.417,3.49 0.271,0.198 10 false 11 5.146,5.438 5.417,5.635 0.271,0.198 10 false 18 5.146,4.906 5.417,5.104 0.271,0.198 10 false 17 5.448,2.865 6.219,3.063 0.771,0.198 10 false CA1P 5.448,3.396 6.219,3.594 0.771,0.198 10 false CA1N 5.448,5 6.219,5.198 0.771,0.198 10 false R1 5.448,5.542 6.219,5.74 0.771,0.198 10 false R2 5.271,3.938 6.583,4.5 1.313,0.563 10 false Forward Recognition Camera*1 5.271,3.781 6.042,3.979 0.771,0.198 10 false R5 5.313,6.083 6.552,6.698 1.24,0.615 10 false Clearance Warning ECU Assembly*2 5.313,5.927 6.083,6.125 0.771,0.198 10 false F142 2.594,5.896 3.365,6.094 0.771,0.198 10 false F164 2.594,6.063 4.625,6.698 2.031,0.635 10 false No. 1 CAN Junction Connector 0.188,6.083 2.167,6.479 1.979,0.396 10 false Central Gateway ECU (Network Gateway ECU) 0.188,5.917 0.958,6.115 0.771,0.198 10 false F74 0.177,6.917 4.156,7.115 3.979,0.198 10 false *1: w/ Toyota Safety Sense 0.177,7.25 4.156,7.448 3.979,0.198 10 false *2: w/ TOYOTA Parking Assist-sensor System 0.063,0.042 1.531,0.281 1.469,0.24 12 false for RHD:


w/ Blind Spot Monitor System


C360938E07
1.354,0.708 1.969,0.906 0.615,0.198 10 false CA2H 1.354,1.25 1.969,1.448 0.615,0.198 10 false CA2L 1.854,0.615 2.219,0.854 0.365,0.24 10 false 3 1.854,1.146 2.219,1.385 0.365,0.24 10 false 2 1.854,2.76 2.219,3 0.365,0.24 10 false 9 1.854,3.281 2.219,3.521 0.365,0.24 10 false 24 1.854,5.396 2.219,5.635 0.365,0.24 10 false 23 1.854,5.927 2.219,6.167 0.365,0.24 10 false 8 1.354,2.76 1.969,2.958 0.615,0.198 10 false CAXH 1.354,3.292 1.969,3.49 0.615,0.198 10 false CAXL 1.354,5.396 1.969,5.594 0.615,0.198 10 false CA1H 1.354,5.927 1.969,6.125 0.615,0.198 10 false CA1L 0.698,3.125 1.313,3.323 0.615,0.198 10 false 120 Ω 0.698,5.771 1.313,5.969 0.615,0.198 10 false 120 Ω 0.208,6.583 2.177,7.031 1.969,0.448 10 false Central Gateway ECU (Network Gateway ECU) 0.208,6.417 0.583,6.667 0.375,0.25 10 false F74 2.688,0.615 3.052,0.854 0.365,0.24 10 false 3 2.615,1.146 2.979,1.385 0.365,0.24 10 false 13 2.625,2.76 2.99,3 0.365,0.24 10 false 10 2.615,3.292 2.979,3.531 0.365,0.24 10 false 20 2.615,5.938 2.979,6.177 0.365,0.24 10 false 21 2.604,5.396 2.969,5.635 0.365,0.24 10 false 10 2.333,4.479 4.313,4.771 1.979,0.292 10 false No. 1 CAN Junction Connector 2.333,4.313 2.948,4.49 0.615,0.177 10 false F111 2.333,7.656 4.625,7.948 2.292,0.292 10 false No. 6 CAN Junction Connector 2.333,7.49 2.948,7.667 0.615,0.177 10 false M104 3.99,0.615 4.396,0.813 0.406,0.198 10 false 2 3.99,1.146 4.448,1.323 0.458,0.177 10 false 12 3.99,2.76 4.396,2.948 0.406,0.188 10 false 1 3.99,3.292 4.406,3.469 0.417,0.177 10 false 11 3.99,3.563 4.5,3.75 0.51,0.188 10 false 19 3.99,3.823 4.448,4.01 0.458,0.188 10 false 9 3.99,5.396 4.458,5.583 0.469,0.188 10 false 11 3.99,5.927 4.427,6.115 0.438,0.188 10 false 22 4,6.469 4.469,6.646 0.469,0.177 10 false 9 3.99,7 4.406,7.177 0.417,0.177 10 false 12 5.219,0.615 5.625,0.813 0.406,0.198 10 false 5 5.146,1.156 5.552,1.354 0.406,0.198 10 false 11 5.146,2.76 5.552,2.958 0.406,0.198 10 false 17 5.146,3.292 5.552,3.49 0.406,0.198 10 false 18 5.219,6.469 5.625,6.667 0.406,0.198 10 false 2 5.219,7 5.625,7.198 0.406,0.198 10 false 7 5.448,0.719 6.063,0.917 0.615,0.198 10 false CA1P 5.448,1.25 6.052,1.448 0.604,0.198 10 false CA1N 5.448,2.854 6.083,3.073 0.635,0.219 10 false R1 5.448,3.385 6.01,3.625 0.563,0.24 10 false R2 5.448,6.563 6.104,6.771 0.656,0.208 10 false CA1P 5.448,7.104 6.104,7.302 0.656,0.198 10 false CA1N 5.292,1.635 5.896,1.833 0.604,0.198 10 false R5 5.292,1.792 6.604,2.323 1.313,0.531 10 false Forward Recognition Camera*1 5.313,3.927 6.542,4.458 1.229,0.531 10 false Clearance Warning ECU Assembly*2 5.313,3.771 5.875,4.01 0.563,0.24 10 false F142 5.344,7.656 6.563,8.188 1.219,0.531 10 false Blind Spot Monitor Sensor LH 5.344,7.49 6,7.688 0.656,0.198 10 false M62 0.208,7.417 2.5,7.708 2.292,0.292 10 false *1: w/ Toyota Safety Sense 0.208,7.75 1.698,8.313 1.49,0.563 10 false *2: w/ TOYOTA Parking Assist-sensor System 0.552,1.635 1.167,1.833 0.615,0.198 10 false A2 0.552,1.802 1.979,2.396 1.427,0.594 10 false Millimeter Wave Radar Sensor Assembly*1 0.063,0.031 2.635,0.271 2.573,0.24 12 false for LHD:

C366135E13
1.385,0.615 2,0.813 0.615,0.198 10 false CA1H 0.698,0.979 1.313,1.177 0.615,0.198 10 false 120 Ω 0.667,3.719 1.281,3.917 0.615,0.198 10 false 120 Ω 1.385,1.167 2,1.365 0.615,0.198 10 false CA1L 1.365,3.365 1.979,3.563 0.615,0.198 10 false CAXH 1.375,3.906 1.99,4.104 0.615,0.198 10 false CAXL 1.833,0.604 2.083,0.802 0.25,0.198 10 false 23 1.854,1.156 2.104,1.354 0.25,0.198 10 false 8 1.875,3.354 2.125,3.552 0.25,0.198 10 false 9 1.844,3.885 2.094,4.083 0.25,0.198 10 false 24 2.24,0.615 2.99,0.802 0.75,0.188 10 false 8*1, 10*2 2.167,1.167 2.906,1.365 0.74,0.198 10 false 19*1, 21*2 3.979,0.604 4.229,0.802 0.25,0.198 10 false 9 3.979,1.156 4.229,1.354 0.25,0.198 10 false 20 4,1.458 4.25,1.656 0.25,0.198 10 false 22 3.99,1.781 4.24,1.979 0.25,0.198 10 false 11 5.219,0.615 5.469,0.813 0.25,0.198 10 false 2 5.219,1.156 5.469,1.354 0.25,0.198 10 false 7 5.438,0.719 6.021,0.917 0.583,0.198 10 false CA1P 5.438,1.25 6.021,1.448 0.583,0.198 10 false CA1N 5.177,1.615 5.76,1.813 0.583,0.198 10 false M62 5.177,1.771 7.104,2.021 1.927,0.25 10 false Blind Spot Monitor Sensor LH 4,3.344 4.25,3.542 0.25,0.198 10 false 5 3.979,3.906 4.229,4.104 0.25,0.198 10 false 11 2.635,3.896 2.885,4.094 0.25,0.198 10 false 12 2.698,3.365 2.948,3.563 0.25,0.198 10 false 6 0.344,4.344 0.677,4.542 0.333,0.198 10 false F74 0.333,4.51 2.333,4.875 2,0.365 10 false Central Gateway ECU (Network Gateway ECU) 2.438,2.229 2.854,2.479 0.417,0.25 10 false M104 2.438,2.396 4.438,2.646 2,0.25 10 false No. 6 CAN Junction Connector 3.99,4.604 5.99,4.854 2,0.25 10 false No. 1 CAN Junction Connector 3.99,4.438 4.573,4.635 0.583,0.198 10 false F164 0.063,0.042 1.531,0.281 1.469,0.24 12 false for RHD: 0.354,5.427 1.688,5.625 1.333,0.198 10 false *1: for TMC Made 1.802,5.427 3.135,5.625 1.333,0.198 10 false *2: for TMMT Made

C366136E08
1.365,1.26 1.979,1.458 0.615,0.198 10 false CA2H 1.396,1.781 2.01,1.979 0.615,0.198 10 false CA2L 0.583,2.146 1.198,2.344 0.615,0.198 10 false A2 0.563,2.313 2.479,2.729 1.917,0.417 10 false Millimeter Wave Radar Sensor Assembly*1 1.833,1.135 2.083,1.302 0.25,0.167 10 false 3 1.854,1.688 2.104,1.854 0.25,0.167 10 false 2 2.708,1.135 2.958,1.302 0.25,0.167 10 false 3 2.698,1.688 2.948,1.854 0.25,0.167 10 false 9 3.99,1.135 4.24,1.302 0.25,0.167 10 false 1 3.99,1.667 4.24,1.833 0.25,0.167 10 false 7 5,1.146 5.25,1.313 0.25,0.167 10 false 17 4.99,1.667 5.24,1.833 0.25,0.167 10 false 18 5.26,1.25 5.594,1.417 0.333,0.167 10 false R1 5.26,1.792 5.594,1.958 0.333,0.167 10 false R2 5.083,2.146 5.417,2.313 0.333,0.167 10 false F142 5.083,2.302 6.667,2.719 1.583,0.417 10 false Clearance Warning ECU Assembly*2 5.01,3.302 5.26,3.469 0.25,0.167 10 false 40 4.99,3.802 5.24,3.969 0.25,0.167 10 false 18 5.25,3.396 5.833,3.563 0.583,0.167 10 false CANH 5.25,3.938 5.833,4.104 0.583,0.167 10 false CANL 5.063,4.292 5.646,4.458 0.583,0.167 10 false M116 5.073,4.469 7.156,4.719 2.083,0.25 10 false Parking Assist ECU*3 2.573,4.292 3.156,4.458 0.583,0.167 10 false F164 2.594,4.448 4.594,4.698 2,0.25 10 false No. 1 CAN Junction Connector 4,3.281 4.25,3.448 0.25,0.167 10 false 4 3.979,3.823 4.229,3.99 0.25,0.167 10 false 10 2.698,3.281 2.948,3.448 0.25,0.167 10 false 2 2.677,3.813 2.927,3.979 0.25,0.167 10 false 8 1.854,3.292 2.104,3.458 0.25,0.167 10 false 5 1.844,3.813 2.094,3.979 0.25,0.167 10 false 11 1.365,3.417 1.948,3.583 0.583,0.167 10 false CA1P 1.354,3.917 1.938,4.083 0.583,0.167 10 false CA1N 0.417,4.26 1,4.427 0.583,0.167 10 false R5 0.427,4.417 2.427,4.667 2,0.25 10 false Forward Recognition Camera*1 0.417,4.833 2.417,5.083 2,0.25 10 false *1: w/ Toyota Safety Sense 0.417,5.156 4,5.406 3.583,0.25 10 false *2: w/ TOYOTA Parking Assist-sensor System 0.438,5.458 4.073,5.677 3.635,0.219 10 false *3: w/ Panoramic View Monitor System 0.073,0.063 1.313,0.448 1.24,0.385 12 false for RHD:


CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the LDA main switch on and then drive the vehicle at a speed of 5 km/h (3 mph) or more for approximately 52 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK VEHICLE TYPE

B

10.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/o Blind Spot Monitor System A
w/ Blind Spot Monitor System B



A

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)

B

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C317371C92
2.052,0.917 2.552,1.167 0.5,0.25 5.521,0.917 6.021,1.167 0.5,0.25 3.594,1.896 4.083,0.792 true 1.365,1.917 0.698,0.583 true 1.01,1.906 0.563,0.948 true 1.083,3.219 1.365,2.177 true 0.646,2.979 0.969,2.198 true 3.615,2.156 3.802,3.083 true 5.688,1.625 6.448,1.198 true 3.948,1.896 4.271,1.094 true 4.021,2.198 4.188,2.802 true 0.313,2.74 0.656,2.188 true 0.677,1.927 0.583,1.323 true 4.115,0.656 5.031,0.854 0.917,0.198 10 false CANH*e 0.167,0.479 1.083,0.677 0.917,0.198 10 false CANH*d 0.042,0.833 0.958,1.031 0.917,0.198 10 false CANH*c 0.313,3.021 1.229,3.219 0.917,0.198 10 false CANL*c 0.813,3.26 1.729,3.458 0.917,0.198 10 false CANL*d 3.552,3.115 4.469,3.313 0.917,0.198 10 false CANL*e 2.135,0.958 2.594,1.156 0.458,0.198 10 false F111 5.594,0.948 6.052,1.146 0.458,0.198 10 false F144 6.5,1.073 7.01,1.271 0.51,0.198 10 false CG 4.729,0.177 5.042,0.375 0.313,0.198 10 false *1 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 4.323,0.948 5.24,1.146 0.917,0.198 10 false CANH*e 3.948,2.844 4.865,3.042 0.917,0.198 10 false CANL*e 0.031,1.219 0.948,1.417 0.917,0.198 10 false CANH*b 0.031,2.74 0.948,2.938 0.917,0.198 10 false CANL*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to Central Gateway ECU (Network Gateway ECU) - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-1 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Clearance warning ECU assembly*1
F111-11 (CANL) - F144-4 (CG)
F111-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward recognition camera*2
F111-12 (CANL) - F144-4 (CG)
F111-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*2
F111-13 (CANL) - F144-4 (CG)
F111-9 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F111-19 (CANL) - F144-4 (CG)
F111-10 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F111-20 (CANL) - F144-4 (CG)



*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense


Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
4.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C317371C93
2.052,0.917 2.552,1.167 0.5,0.25 5.521,0.917 6.021,1.167 0.5,0.25 3.604,1.906 4.125,0.948 true 3.594,2.177 3.813,3.042 true 5.708,1.604 6.365,1.208 true 3.958,1.906 4.229,1.271 true 3.99,2.135 4.188,2.667 true 4.188,0.833 5.104,1.031 0.917,0.198 10 false CANH*b 3.583,3.083 4.5,3.281 0.917,0.198 10 false CANL*b 2.146,0.958 2.604,1.156 0.458,0.198 10 false F111 5.604,0.948 6.063,1.146 0.458,0.198 10 false F144 6.417,1.094 6.927,1.292 0.51,0.198 10 false CG 4.729,0.177 5.042,0.375 0.313,0.198 10 false *1 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 4.292,1.167 5.208,1.365 0.917,0.198 10 false CANH*b 3.948,2.708 4.865,2.906 0.917,0.198 10 false CANL*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F111-9 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F111-19 (CANL) - F144-4 (CG)
F111-10 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F111-20 (CANL) - F144-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 6 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C425191C69
5.542,1 6.042,1.25 0.5,0.25 1.75,1.083 2.25,1.333 0.5,0.25 2.948,2.823 2.5,2.052 true 6.406,1.25 5.698,1.635 true 3.052,2.531 2.635,2.042 true 2.771,3.021 2.354,2.073 true 2.938,0.917 2.354,1.833 true 3.073,1.427 2.625,1.854 true 3.073,1.135 2.479,1.833 true 3.115,1.281 4.031,1.479 0.917,0.198 10 false CANH*d 3.146,1.01 4.063,1.208 0.917,0.198 10 false CANH*c 3.01,0.781 3.927,0.979 0.917,0.198 10 false CANH*b 2.542,3.052 3.458,3.25 0.917,0.198 10 false CANL*b 3.01,2.75 3.927,2.948 0.917,0.198 10 false CANL*c 3.104,2.5 4.021,2.698 0.917,0.198 10 false CANL*d 6.469,1.146 6.865,1.417 0.396,0.271 10 false CG 5.625,1.031 6.292,1.302 0.667,0.271 10 false F144 1.823,1.115 2.49,1.385 0.667,0.271 10 false M104 0.198,0.167 1.115,0.365 0.917,0.198 10 false *a 4.583,0.229 5.5,0.427 0.917,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Blind Spot Monitor Sensor LH
*c to Central Gateway ECU (Network Gateway ECU) *d to No. 1 CAN Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
M104-9 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor LH
M104-20 (CANL) - F144-4 (CG)
M104-10 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
M104-21 (CANL) - F144-4 (CG)
M104-11 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 1 CAN junction connector
M104-22 (CANL) - F144-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 1 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)

D

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
6.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C425191C70
5.542,1 6.042,1.25 0.5,0.25 1.75,1.083 2.25,1.333 0.5,0.25 6.427,1.26 5.729,1.615 true 3.031,2.26 2.521,2.042 true 2.542,1.865 3.031,1.656 true 3.125,1.563 4.042,1.76 0.917,0.198 10 false CANH*b 3.083,2.208 4,2.406 0.917,0.198 10 false CANL*b 6.49,1.135 7.01,1.385 0.521,0.25 10 false CG 5.625,1.031 6.292,1.302 0.667,0.271 10 false F144 1.844,1.115 2.51,1.385 0.667,0.271 10 false M104 0.146,0.125 1.063,0.323 0.917,0.198 10 false *a 4.51,0.146 5.427,0.344 0.917,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
M104-10 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M104-21 (CANL) - F144-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C317371C94
2.052,0.917 2.552,1.167 0.5,0.25 5.521,0.917 6.021,1.167 0.5,0.25 3.594,1.896 4.094,0.938 true 1.354,1.906 0.708,0.563 true 1.021,1.906 0.604,0.844 true 1.177,3.208 1.375,2.198 true 0.76,2.927 0.979,2.177 true 3.615,2.156 3.875,2.927 true 5.719,1.635 6.25,1.177 true 3.969,1.906 4.219,1.302 true 3.979,2.167 4.146,2.583 true 0.25,2.719 0.625,2.188 true 0.677,1.896 0.583,1.198 true 4.135,0.823 5.052,1.021 0.917,0.198 10 false CANH*e 0.167,0.458 1.083,0.656 0.917,0.198 10 false CANH*d 0.063,0.75 0.979,0.948 0.917,0.198 10 false CANH*c 0.552,2.938 1.469,3.135 0.917,0.198 10 false CANL*c 0.906,3.24 1.823,3.438 0.917,0.198 10 false CANL*d 3.927,2.865 4.844,3.063 0.917,0.198 10 false CANL*e 2.135,0.958 2.594,1.156 0.458,0.198 10 false F111 5.604,0.948 6.063,1.146 0.458,0.198 10 false F144 6.323,1.073 6.833,1.271 0.51,0.198 10 false CG 4.729,0.177 5.042,0.375 0.313,0.198 10 false *1 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 4.271,1.198 5.188,1.396 0.917,0.198 10 false CANH*f 4.219,2.552 5.135,2.75 0.917,0.198 10 false CANL*f 0.042,1.104 0.958,1.302 0.917,0.198 10 false CANH*b 0.031,2.729 0.948,2.927 0.917,0.198 10 false CANL*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to No. 6 CAN Junction Connector *f to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F111-1 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Clearance Warning ECU assembly*1
F111-11 (CANL) - F144-4 (CG)
F111-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward recognition camera*2
F111-12 (CANL) - F144-4 (CG)
F111-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*2
F111-13 (CANL) - F144-4 (CG)
F111-9 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 6 CAN junction connector
F111-19 (CANL) - F144-4 (CG)
F111-10 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F111-20 (CANL) - F144-4 (CG)


*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 6 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

D

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C317371C95
2.052,0.917 2.552,1.167 0.5,0.25 5.521,0.917 6.021,1.167 0.5,0.25 5.719,1.625 6.417,1.229 true 3.969,1.896 4.219,1.271 true 3.979,2.167 4.313,2.813 true 2.167,0.958 2.625,1.156 0.458,0.198 10 false F111 5.615,0.948 6.073,1.146 0.458,0.198 10 false F144 6.469,1.135 6.979,1.333 0.51,0.198 10 false CG 4.729,0.177 5.042,0.375 0.313,0.198 10 false *1 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 4.26,1.146 5.177,1.344 0.917,0.198 10 false CANH*b 4.083,2.833 5,3.031 0.917,0.198 10 false CANL*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F111-10 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F111-20 (CANL) - F144-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C425199C02
4.958,0.5 5.458,0.75 0.5,0.25 1.625,0.5 2.125,0.75 0.5,0.25 5.823,0.708 5.135,1.135 true 1.313,1.229 1.094,0.635 true 0.938,2.042 1.25,1.396 true 0.729,0.552 1.344,0.75 0.615,0.198 10 false CA1L 0.708,2.073 1.323,2.271 0.615,0.198 10 false CA1H 5.042,0.542 5.656,0.74 0.615,0.198 10 false F144 1.74,0.542 2.354,0.74 0.615,0.198 10 false F74 5.865,0.604 6.479,0.802 0.615,0.198 10 false CG 4.115,0.198 4.427,0.396 0.313,0.198 10 false *1 0.177,0.188 0.49,0.385 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F74-23 (CA1H) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-8 (CA1L) - F144-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/o Blind Spot Monitor System A
w/ Blind Spot Monitor System B



A

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)

B

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR)
11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C404459C49
1.75,0.5 2.25,0.75 0.5,0.25 5,0.5 5.5,0.75 0.5,0.25 5.115,1.125 5.875,0.74 true 1.146,1.354 0.792,1.177 true 1.438,1.365 0.833,0.896 true 1.771,1.354 1.063,0.646 true 1.135,1.552 0.844,1.833 true 1.458,1.583 1.01,2.135 true 1.792,1.573 1.344,2.302 true 2.813,1.365 3.083,1.198 true 2.802,1.563 3.135,1.698 true 2.479,1.583 3.021,1.99 true 2.458,1.344 3.052,0.896 true 4.063,0.271 4.375,0.427 0.313,0.156 10 false *1 0.281,0.104 0.594,0.26 0.313,0.156 10 false *a 0.302,1.75 0.885,1.958 0.583,0.208 10 false CANL*b 0.438,2.052 1.021,2.26 0.583,0.208 10 false CANL*c 1.104,2.333 1.688,2.542 0.583,0.208 10 false CANL*d 3.094,1.906 3.677,2.115 0.583,0.208 10 false CANL*e 0.25,1.094 0.833,1.302 0.583,0.208 10 false CANH*b 0.281,0.802 0.865,1.01 0.583,0.208 10 false CANH*c 0.49,0.542 1.073,0.75 0.583,0.208 10 false CANH*d 1.833,0.542 2.417,0.75 0.583,0.208 10 false F164 5.104,0.542 5.688,0.75 0.583,0.208 10 false F144 5.948,0.615 6.531,0.823 0.583,0.208 10 false CG 3.188,1.604 3.771,1.813 0.583,0.208 10 false CANL*e 3.135,1.094 3.719,1.302 0.583,0.208 10 false CANH*e 3.115,0.771 3.698,0.979 0.583,0.208 10 false CANH*e
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to Central Gateway ECU (Network Gateway ECU) - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F164-1 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Clearance warning ECU assembly*1
F164-7 (CANL) - F144-4 (CG)
F164-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward recognition camera*2
F164-8 (CANL) - F144-4 (CG)
F164-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*2
F164-9 (CANL) - F144-4 (CG)
F164-5 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F164-11 (CANL) - F144-4 (CG)
F164-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F164-12 (CANL) - F144-4 (CG)



*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense


Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

17.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C404459C50
1.75,0.5 2.25,0.75 0.5,0.25 5,0.5 5.5,0.75 0.5,0.25 5.167,1.104 5.958,0.719 true 2.813,1.365 3.083,1.198 true 2.802,1.563 3.135,1.698 true 2.479,1.583 3.021,1.99 true 2.458,1.344 3.052,0.896 true 4.063,0.271 4.375,0.427 0.313,0.156 10 false *1 0.281,0.104 0.594,0.26 0.313,0.156 10 false *a 3.094,1.906 3.677,2.115 0.583,0.208 10 false CANL*b 1.833,0.542 2.417,0.75 0.583,0.208 10 false F164 5.104,0.542 5.688,0.75 0.583,0.208 10 false F144 6.021,0.625 6.604,0.833 0.583,0.208 10 false CG 3.188,1.604 3.771,1.813 0.583,0.208 10 false CANL*b 3.135,1.083 3.719,1.292 0.583,0.208 10 false CANH*b 3.115,0.771 3.698,0.979 0.583,0.208 10 false CANH*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F164-5 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F164-11 (CANL) - F144-4 (CG)
F164-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F164-12 (CANL) - F144-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the No. 6 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C425191C71
5.542,1 6.042,1.25 0.5,0.25 1.75,1.083 2.25,1.333 0.5,0.25 2.938,2.813 2.406,2.073 true 6.302,1.26 5.677,1.615 true 3.052,2.531 2.51,2.042 true 2.823,3.083 2.25,2.073 true 2.833,0.854 2.281,1.844 true 3.073,1.427 2.531,1.854 true 2.969,1.115 2.375,1.844 true 3.115,2.375 2.625,2.042 true 3.115,1.604 2.646,1.875 true 3.115,1.281 4.031,1.479 0.917,0.198 10 false CANH*d 3.031,1 3.948,1.198 0.917,0.198 10 false CANH*c 2.896,0.729 3.813,0.927 0.917,0.198 10 false CANH*b 2.906,3.063 3.823,3.26 0.917,0.198 10 false CANL*b 2.969,2.75 3.885,2.948 0.917,0.198 10 false CANL*c 3.104,2.5 4.021,2.698 0.917,0.198 10 false CANL*d 6.375,1.146 6.771,1.417 0.396,0.271 10 false CG 5.625,1.031 6.292,1.302 0.667,0.271 10 false F144 1.823,1.115 2.49,1.385 0.667,0.271 10 false M104 0.198,0.167 1.115,0.365 0.917,0.198 10 false *a 4.583,0.229 5.5,0.427 0.917,0.198 10 false *1 3.167,2.313 4.083,2.51 0.917,0.198 10 false CANL*e 3.167,1.531 4.083,1.729 0.917,0.198 10 false CANH*e
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU) (for TMC Made)
*c to Blind Spot Monitor Sensor LH *d to Central Gateway ECU (Network Gateway ECU) (for TMMT Made)
*e to No. 1 CAN Junction Connector - -


Standard Resistance:
for TMC Made
Tester Connection Condition Specified Condition Connected to
M104-8 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
M104-19 (CANL) - F144-4 (CG)
M104-9 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor LH
M104-20 (CANL) - F144-4 (CG)
M104-11 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 1 CAN junction connector
M104-22 (CANL) - F144-4 (CG)

for TMMT Made
Tester Connection Condition Specified Condition Connected to
M104-9 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Blind spot monitor sensor LH
M104-20 (CANL) - F144-4 (CG
M104-10 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
M104-21 (CANL) - F144-4 (CG)
M104-11 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher No. 1 CAN junction connector
M104-22 (CANL) - F144-4 (CG)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 1 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)

D

17.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C425191C72
5.542,1 6.042,1.25 0.5,0.25 1.75,1.083 2.25,1.333 0.5,0.25 6.26,1.219 5.708,1.615 true 3.073,2.375 2.49,2.042 true 2.521,1.875 3.083,1.635 true 2.792,2.677 2.271,2.052 true 2.25,1.854 2.865,1.198 true 2.948,1.083 3.865,1.281 0.917,0.198 10 false CANH*b 3.125,2.323 4.042,2.521 0.917,0.198 10 false CANL*c 6.313,1.104 6.833,1.354 0.521,0.25 10 false CG 5.615,1.031 6.281,1.302 0.667,0.271 10 false F144 1.844,1.115 2.51,1.385 0.667,0.271 10 false M104 0.146,0.125 1.063,0.323 0.917,0.198 10 false *a 4.51,0.146 5.427,0.344 0.917,0.198 10 false *1 3.146,1.542 4.063,1.74 0.917,0.198 10 false CANH*c 2.875,2.625 3.792,2.823 0.917,0.198 10 false CANL*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU) (for TMC Made)
*c to Central Gateway ECU (Network Gateway ECU) (for TMMT Made) - -


Standard Resistance:
for TMC Made
Tester Connection Condition Specified Condition
M104-8 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M104-19 (CANL) - F144-4 (CG)

for TMMT Made
Tester Connection Condition Specified Condition
M104-10 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M104-21 (CANL) - F144-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C404459C51
1.75,0.5 2.25,0.75 0.5,0.25 5,0.5 5.5,0.75 0.5,0.25 5.177,1.115 6.052,0.729 true 1.146,1.354 0.792,1.177 true 1.438,1.365 0.833,0.896 true 1.771,1.354 1.063,0.646 true 1.135,1.552 0.844,1.833 true 1.458,1.583 1.01,2.135 true 1.792,1.573 1.344,2.302 true 2.813,1.365 3.083,1.198 true 2.802,1.563 3.135,1.698 true 2.479,1.583 3.021,1.99 true 2.458,1.344 3.052,0.896 true 2.146,1.354 2.917,0.604 true 2.146,1.583 2.531,2.25 true 4.063,0.271 4.375,0.427 0.313,0.156 10 false *1 0.281,0.104 0.594,0.26 0.313,0.156 10 false *a 0.302,1.75 0.885,1.958 0.583,0.208 10 false CANL*b 0.438,2.052 1.021,2.26 0.583,0.208 10 false CANL*c 1.104,2.333 1.688,2.542 0.583,0.208 10 false CANL*d 3.094,1.896 3.677,2.104 0.583,0.208 10 false CANL*f 0.25,1.094 0.833,1.302 0.583,0.208 10 false CANH*b 0.281,0.802 0.865,1.01 0.583,0.208 10 false CANH*c 0.49,0.542 1.073,0.75 0.583,0.208 10 false CANH*d 1.833,0.542 2.417,0.75 0.583,0.208 10 false F164 5.083,0.542 5.667,0.75 0.583,0.208 10 false F144 6.125,0.635 6.708,0.844 0.583,0.208 10 false CG 3.188,1.604 3.771,1.813 0.583,0.208 10 false CANL*g 3.135,1.094 3.719,1.302 0.583,0.208 10 false CANH*g 3.115,0.771 3.698,0.979 0.583,0.208 10 false CANH*f 2.979,0.469 3.563,0.677 0.583,0.208 10 false CANH*e 2.365,2.313 2.948,2.521 0.583,0.208 10 false CANL*e
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to Parking Assist ECU
(w/ Panoramic View Monitor System)
*f to No. 6 CAN Junction Connector
*g to Central Gateway ECU (Network Gateway ECU) - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F164-1 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Clearance Warning ECU assembly*1
F164-7 (CANL) - F144-4 (CG)
F164-2 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Forward recognition camera*2
F164-8 (CANL) - F144-4 (CG)
F164-3 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*2
F164-9 (CANL) - F144-4 (CG)
F164-4 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Parking assist ECU*3
F164-10 (CANL) - F144-4 (CG)
F164-5 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 6 CAN junction connector
F164-11 (CANL) - F144-4 (CG)
F164-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F164-12 (CANL) - F144-4 (CG)


*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense

*3: w/ Panoramic View Monitor System



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 6 CAN junction connector) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

16.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

D

17.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
16.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C404459C52
1.75,0.5 2.25,0.75 0.5,0.25 5,0.5 5.5,0.75 0.5,0.25 5.156,1.115 5.896,0.75 true 2.813,1.365 3.083,1.198 true 2.802,1.563 3.135,1.698 true 4.063,0.271 4.375,0.427 0.313,0.156 10 false *1 0.281,0.104 0.594,0.26 0.313,0.156 10 false *a 1.833,0.542 2.417,0.75 0.583,0.208 10 false F164 5.094,0.542 5.677,0.75 0.583,0.208 10 false F144 5.979,0.656 6.563,0.865 0.583,0.208 10 false CG 3.188,1.604 3.771,1.813 0.583,0.208 10 false CANL*b 3.135,1.083 3.719,1.292 0.583,0.208 10 false CANH*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F164-6 (CANH) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F164-12 (CANL) - F144-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

17.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C425199C02
4.958,0.5 5.458,0.75 0.5,0.25 1.625,0.5 2.125,0.75 0.5,0.25 5.823,0.708 5.135,1.135 true 1.313,1.229 1.094,0.635 true 0.938,2.042 1.25,1.396 true 0.729,0.552 1.344,0.75 0.615,0.198 10 false CA1L 0.708,2.073 1.323,2.271 0.615,0.198 10 false CA1H 5.042,0.542 5.656,0.74 0.615,0.198 10 false F144 1.74,0.542 2.354,0.74 0.615,0.198 10 false F74 5.865,0.604 6.479,0.802 0.615,0.198 10 false CG 4.115,0.198 4.427,0.396 0.313,0.198 10 false *1 0.177,0.188 0.49,0.385 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F74-23 (CA1H) - F144-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F74-8 (CA1L) - F144-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR