There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| No resistance exists between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3. | ·
Short to ground in CAN main bus line ·
Short to ground in CAN branch line ·
Main body ECU (multiplex network body ECU) ·
Certification ECU (smart key ECU assembly) ·
Central gateway ECU (network gateway ECU) ·
Combination meter assembly ·
Air conditioning amplifier assembly ·
Headlight ECU sub-assembly LH (for LED Headlight) ·
No. 3 CAN junction connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the LDA main switch on and wait for approximately 20 seconds or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the No. 3 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to Combination Meter Assembly |
| *c | to Main Body ECU (Multiplex Network Body ECU) | *d | to Headlight ECU Sub-assembly LH
(for LED Headlight) |
| *e | to Air Conditioning Amplifier Assembly | *f | to Certification ECU (Smart Key ECU Assembly) |
| *g | to Central Gateway ECU (Network Gateway ECU) | - | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F114-1 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Combination meter assembly |
| F114-12 (CANL) - F144-4 (CG) | |||
| F114-2 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Main body ECU (multiplex network body ECU) |
| F114-13 (CANL) - F144-4 (CG) | |||
| F114-3 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Headlight ECU sub-assembly LH*1 |
| F114-14 (CANL) - F144-4 (CG) | |||
| F114-4 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Air conditioning amplifier assembly |
| F114-15 (CANL) - F144-4 (CG) | |||
| F114-5 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Certification ECU (smart key ECU assembly) |
| F114-16 (CANL) - F144-4 (CG) | |||
| F114-6 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Central gateway ECU (network gateway ECU) |
| F114-17 (CANL) - F144-4 (CG) |
*1: for LED Headlight
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to ECU or sensor) | C |
A
B
C
Disconnect the F74 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F114-6 (CANH) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F114-17 (CANL) - F144-4 (CG) |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F74-15 (CA5H) - F144-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| F74-16 (CA5L) - F144-4 (CG) |
If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to ground in the wire harness and repair or replace the wire harness or connector if necessary.
| Result |
|---|
| OK |
| NG |
OK
NG