This DTC is stored when the SSW1 contact signal and SSW2 contact signal, which are detected when the power switch is operated, do not match.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2278 | Engine/Power Switch Malfunction | When the power switch is operated, the SSW1 contact signal and SSW2 contact signal do not match (1-trip detection logic*). | ·
AM2 fuse ·
Power switch ·
Certification ECU (smart key ECU assembly) ·
Wire harness or connector |
DTC Output Confirmation Operation:
Turn the power switch on (IG). |
*: Only detected while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| If either the SSW1 contact signal or SSW2 contact signal is stuck on, the power source mode cannot be changed by pressing the power switch. If either the SSW1 contact signal or SSW2 contact signal is stuck off, emergency stop by pressing and holding the power switch for 2 seconds or more cannot be operated. | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2278 | Power Source Control
·
Starter Switch1 ·
Starter Switch2 |
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Start Function) Precaution.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Start Switch1 | Power switch 1 status | OFF or ON | OFF: Power switch not pressed
ON: Power switch pressed |
·
If the power switch is pressed for a short time, the display may not change. ·
Use this item to determine if the power switch input signal is malfunctioning. |
| Start Switch2 | Power switch 2 status | OFF or ON | OFF: Power switch not pressed
ON: Power switch pressed |
·
Backup for power switch 1. However, when the power switch is pressed and held, the power source mode can only be changed when both power switch 1 and 2 are normal. ·
Behaves the same way as power switch 1. |
| Tester Display |
|---|
| Start Switch1 |
| Start Switch2 |
The GTS display changes correctly in response to the power switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List while wiggling the wire harness.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Start Switch1 | Power switch 1 status | OFF or ON | OFF: Power switch not pressed
ON: Power switch pressed |
·
If the power switch is pressed for a short time, the display may not change. ·
Use this item to determine if the power switch input signal is malfunctioning. |
| Start Switch2 | Power switch 2 status | OFF or ON | OFF: Power switch not pressed
ON: Power switch pressed |
·
Backup for power switch 1. However, when the power switch is pressed and held, the power source mode can only be changed when both power switch 1 and 2 are normal. ·
Behaves the same way as power switch 1. |
| Tester Display |
|---|
| Start Switch1 |
| Start Switch2 |
The GTS display changes correctly in response to the power switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F1 certification ECU (smart key ECU assembly) connector.
Disconnect the F59 power switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-23 (SSW1) - F59-5 (SS1) | Always | Below 1 Ω |
| F1-21 (SSW2) - F59-1 (SS2) | Always | Below 1 Ω |
| F1-11 (AGND) - F59-6 (AGND) | Always | Below 1 Ω |
| F1-23 (SSW1) or F59-5 (SS1) - Body ground | Always | 10 kΩ or higher |
| F1-21 (SSW2) or F59-1 (SS2) - Body ground | Always | 10 kΩ or higher |
| F1-11 (AGND) or F59-6 (AGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power switch.
for LHD with 2ZR-FXE: Click hereEngine / Hybrid System>2ZR-FXE (STARTING)>POWER SWITCH (for LHD)>REMOVAL
for RHD with 2ZR-FXE: Click hereEngine / Hybrid System>2ZR-FXE (STARTING)>POWER SWITCH (for RHD)>REMOVAL
for LHD with M20A-FXS: Click hereEngine / Hybrid System>M20A-FXS (STARTING)>POWER SWITCH (for LHD)>REMOVAL
for RHD with M20A-FXS: Click hereEngine / Hybrid System>M20A-FXS (STARTING)>POWER SWITCH (for RHD)>REMOVAL
Inspect the power switch.
for LHD with 2ZR-FXE: Click hereEngine / Hybrid System>2ZR-FXE (STARTING)>POWER SWITCH (for LHD)>INSPECTION
for RHD with 2ZR-FXE: Click hereEngine / Hybrid System>2ZR-FXE (STARTING)>POWER SWITCH (for RHD)>INSPECTION
for LHD with M20A-FXS: Click hereEngine / Hybrid System>M20A-FXS (STARTING)>POWER SWITCH (for LHD)>INSPECTION
for RHD with M20A-FXS: Click hereEngine / Hybrid System>M20A-FXS (STARTING)>POWER SWITCH (for RHD)>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD with 2ZR-FXE) | B |
| NG (for RHD with 2ZR-FXE) | C |
| NG (for LHD with M20A-FXS) | D |
| NG (for RHD with M20A-FXS) | E |
A
B
C
D
E