When the electrical key transmitter sub-assembly is in the cabin and the power switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever is in P and the brake pedal is depressed, the hybrid control system can be started by pressing the power switch. If the steering is unlocked, the hybrid control system can also be started by pressing the power switch with the shift lever in P and the brake pedal depressed.
| Problem Symptom | Data List and Active Test |
|---|---|
| Power source mode does not change to ON (READY) | Power Source Control
·
Stop Light Switch1 ·
Steering Unlock Switch ·
Shift P Signal ·
IG Relay Monitor (Inside) ·
IG Relay Monitor (Outside) ·
Latch Circuit ·
Starter Request Signal ·
Power Supply Condition Entry&Start
·
Immobiliser ·
Engine Start Request ·
S Code Check ·
L Code Check |
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to entry and start system (for Start Function) Precaution.
After completing repairs, confirm that the problem does not recur.
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
If the power switch is turned from on (IG) to on (ACC) with the shift lever in any position other than P, and then the shift lever is moved to P and the power switch is pressed with the brake pedal depressed, the power switch will turn off.
Press a switch of the electrical key transmitter sub-assembly.
The electrical key transmitter sub-assembly LED illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Key Low Battery | Transmitter battery depleted | No or Yes | No: Transmitter battery not depleted
Yes: Transmitter battery depleted |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new). |
| Tester Display |
|---|
| Key Low Battery |
| Result | Proceed to |
|---|---|
| "No" is displayed on the GTS screen | A |
| "Yes" is displayed on the GTS screen | B |
A
B
If the problem occurs in certain locations or times of day, the possibility of wave interference is high.
Whether the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the door control receiver.
Power source mode changes to on (READY).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P.
With the brake pedal released, check that pressing the power switch causes the power source mode to change.
| Result | Proceed to |
|---|---|
| Power source mode changes : Off → on (ACC) → on (IG) → off | A |
| Power source mode does not change to on (ACC) or on (IG) | B |
| Power source mode changes to on (IG) but not to on (ACC) | C |
| Power source mode changes to on (ACC) but not to on (IG) | D |
A
B
C
D
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift P Signal | Shift position P | OFF or ON | OFF: Shift lever not in P
ON: Shift lever in P |
Use this item to determine whether the shift lever position switch (P) is malfunctioning. |
| Tester Display |
|---|
| Shift P Signal |
The GTS display changes correctly in response to the shift lever operation.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 2ZR-FXE with Nickel Metal Hydride Battery) | B |
| NG (for 2ZR-FXE with Lithium-ion Battery) | C |
| NG (for M20A-FXS) | D |
A
B
C
D
Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Entry and start system (for Start Function) DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Switch1 | State of brake pedal | OFF or ON | OFF: Brake pedal released
ON: Brake pedal depressed |
·
Use this item to determine if the stop light switch assembly is malfunctioning. ·
The hybrid control system cannot be started when this item is OFF. ·
If the stop light switch assembly is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time. |
| Tester Display |
|---|
| Stop Light Switch1 |
The GTS display changes correctly in response to the brake pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F1-3 (IGB) - Body ground | Power switch off → Power switch on (IG) | 1 V or less → 8.5 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter Request Signal | Hybrid control system start request signal status | OFF or ON | OFF: The power switch is not pressed
ON: With the shift lever in P and the brake pedal depressed, the power switch is pressed and held |
·
When the hybrid control system cannot be started due to a start request signal malfunction, OFF is displayed. ·
When the power switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the power switch needs to be pressed and held for a certain period of time. |
| Tester Display |
|---|
| Starter Request Signal |
Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the power switch.
The GTS display changes correctly in response to the power switch operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F1 certification ECU (smart key ECU assembly) connector.
Disconnect the F2*1 or F161*2 hybrid vehicle control ECU connector.
*1: for 2ZR-FXE
*2: for M20A-FXS
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-27 (ST2) - F2-9 (ST2) | Always | Below 1 Ω |
| F1-27 (ST2) or F2-9 (ST2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-27 (ST2) - F161-4 (ST2) | Always | Below 1 Ω |
| F1-27 (ST2) or F161-4 (ST2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F1 certification ECU (smart key ECU assembly) connector.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-27 (ST2) - Body ground | Power switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after power switch released (starter off) | 8.5 V or higher → 1.0 V or less |
| Result | Proceed to |
|---|---|
| OK (for 2ZR-FXE with Nickel Metal Hydride Battery) | A |
| OK (for 2ZR-FXE with Lithium-ion Battery) | B |
| OK (for M20A-FXS) | C |
| NG | D |
A
B
C
D
Inspect the transmitter battery.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER>INSPECTION
Do not wrap the lead wire ground a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the steering unlocks when the power switch is turned on (ACC).
The steering unlocks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P.
Press the power switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
The security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>PROBLEM SYMPTOMS TABLE
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A91-7 (B) - Body ground | Power switch off | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A91-2 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M67 certification ECU (smart key ECU assembly) connector.
Disconnect the A91 stop light switch assembly connector.
Disconnect the A49*1 or A97*2 hybrid vehicle control ECU connector.
*1: for 2ZR-FXE
*2: for M20A-FXS
Disconnect the A39 brake booster with master cylinder assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M67-25 (STP1) - A91-3 (L) | Always | Below 1 Ω |
| M67-25 (STP1) or A91-3 (L) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG