Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2019.09
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0303649 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.

·

With the electrical key transmitter sub-assembly in the cabin, the power switch is pressed.

·

When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed with the electrical key transmitter sub-assembly held near the power switch.

·

When the entry and start system has been canceled, the brake pedal is depressed with the electrical key transmitter sub-assembly held near the power switch.


Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

IG Relay Monitor (Inside)

·

ACC Relay Monitor

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Power Supply Condition



WIRING DIAGRAM

E352018E09
0.042,1.125 0.906,1.719 0.865,0.594 10 false from Auxiliary Battery 1.323,1.281 1.698,1.448 0.375,0.167 10 false AM2 1.927,1.135 2.177,1.302 0.25,0.167 10 false F1 1.969,0.958 2.219,1.125 0.25,0.167 10 false 4 2.25,1.125 2.5,1.292 0.25,0.167 10 false +B 2.729,0.313 2.979,0.479 0.25,0.167 10 false +B 2.354,0.615 2.521,0.802 0.167,0.188 10 false IC 2.948,0.667 3.354,0.854 0.406,0.188 10 false ACCD 3.5,0.594 3.75,0.76 0.25,0.167 10 false 16 3.51,0.76 3.76,0.927 0.25,0.167 10 false F1 3.917,0.76 4.167,0.927 0.25,0.167 10 false 3A 3.917,0.313 4.167,0.479 0.25,0.167 10 false 3K 3.938,0.594 4.188,0.76 0.25,0.167 10 false 30 4.74,0.99 5.115,1.177 0.375,0.188 10 false ACC 5.708,0.458 6.448,0.667 0.74,0.208 10 false ECU-ACC 6.708,0.156 6.958,0.323 0.25,0.167 10 false 40 6.698,0.313 6.948,0.479 0.25,0.167 10 false 3A 2.354,1.656 2.521,1.844 0.167,0.188 10 false IC 2.729,1.302 2.979,1.469 0.25,0.167 10 false +B 3.021,1.698 3.385,1.865 0.365,0.167 10 false IG1D 3.5,1.792 3.75,1.958 0.25,0.167 10 false F1 3.927,1.792 4.177,1.958 0.25,0.167 10 false 3A 3.5,1.615 3.75,1.781 0.25,0.167 10 false 17 3.927,1.615 4.177,1.781 0.25,0.167 10 false 17 1.948,2.521 2.198,2.688 0.25,0.167 10 false 18 1.927,2.698 2.177,2.865 0.25,0.167 10 false F1 2.26,2.708 2.51,2.875 0.25,0.167 10 false E 4.563,2.031 5.26,2.198 0.698,0.167 10 false IG1-NO. 1 5.552,1.615 6.542,1.802 0.99,0.188 10 false ECU-IG1 NO. 3 6.698,1.479 6.948,1.646 0.25,0.167 10 false 3F 6.698,1.292 6.948,1.458 0.25,0.167 10 false 10 4.573,3.208 5.271,3.375 0.698,0.167 10 false IG1-NO. 2 5.719,2.708 6.417,2.875 0.698,0.167 10 false WIPER RR 6.708,2.375 6.958,2.542 0.25,0.167 10 false 12 6.708,2.563 6.958,2.729 0.25,0.167 10 false 3H 1.021,3.615 1.333,3.781 0.313,0.167 10 false SS1 1.385,3.604 1.698,3.771 0.313,0.167 10 false 5 1.021,4.24 1.333,4.406 0.313,0.167 10 false SS2 1.385,4.24 1.698,4.406 0.313,0.167 10 false 1 0.906,4.865 1.385,5.052 0.479,0.188 10 false AGND 1.396,4.854 1.708,5.021 0.313,0.167 10 false 6 1.958,3.521 2.271,3.688 0.313,0.167 10 false 23 1.938,4.156 2.25,4.323 0.313,0.167 10 false 21 1.958,3.708 2.208,3.875 0.25,0.167 10 false F1 1.958,4.344 2.208,4.51 0.25,0.167 10 false F1 1.948,4.969 2.198,5.135 0.25,0.167 10 false F1 2.25,3.594 2.719,3.75 0.469,0.156 10 false SSW1 2.25,4.24 2.719,4.396 0.469,0.156 10 false SSW2 2.271,4.865 2.74,5.021 0.469,0.156 10 false AGND 1.927,4.771 2.24,4.938 0.313,0.167 10 false 11 0.385,5.313 0.719,5.479 0.333,0.167 10 false F59 0.385,5.49 1.406,5.719 1.021,0.229 10 false Power Switch 3.115,4.01 3.323,4.229 0.208,0.219 10 false IC 2.667,3.083 2.917,3.25 0.25,0.167 10 false +B 3.938,3.49 4.115,3.708 0.177,0.219 10 false 1 3.927,3.688 4.125,3.875 0.198,0.188 10 false 3L 3.906,3.969 4.115,4.146 0.208,0.177 10 false 13 3.917,4.354 4.125,4.531 0.208,0.177 10 false 12 3.927,4.146 4.125,4.333 0.198,0.188 10 false 3F 3.938,4.531 4.135,4.719 0.198,0.188 10 false 3F 4.573,4.385 5.302,4.563 0.729,0.177 10 false IG2-NO. 2 5.563,3.844 6.604,4.042 1.042,0.198 10 false ECU-IG2 NO. 3 6.698,3.51 6.948,3.677 0.25,0.167 10 false 19 6.729,3.969 6.979,4.135 0.25,0.167 10 false 3 6.698,3.688 6.948,3.854 0.25,0.167 10 false 3D 6.708,4.146 6.958,4.313 0.25,0.167 10 false 3D 4.135,4.781 6.896,5.073 2.76,0.292 10 false Instrument Panel Junction Block Assembly 0.156,6.292 0.281,6.469 0.125,0.177 10 false 7 0.354,6.417 0.521,6.594 0.167,0.177 10 false B 1.313,6.448 1.479,6.625 0.167,0.177 10 false 2 1.302,6.156 1.469,6.333 0.167,0.177 10 false 3 1.125,6.177 1.292,6.354 0.167,0.177 10 false L 0.917,6.531 1.281,6.719 0.365,0.188 10 false GND 0.177,6.885 0.542,7.073 0.365,0.188 10 false A91 0.156,7.063 2.094,7.313 1.938,0.25 10 false Stop Light Switch Assembly 0.25,7.917 0.781,8.115 0.531,0.198 10 false STOP 1.094,7.781 1.969,8.323 0.875,0.542 10 false from Auxiliary Battery 1.958,6.083 2.125,6.26 0.167,0.177 10 false 25 1.906,6.271 2.229,6.479 0.323,0.208 10 false M67 2.25,6.167 2.885,6.333 0.635,0.167 10 false STP1 3.073,6.375 3.281,6.594 0.208,0.219 10 false IC 3.979,5.875 4.615,6.042 0.635,0.167 10 false WIPER 4.771,5.635 4.938,5.813 0.167,0.177 10 false 4 4.771,6.073 4.938,6.25 0.167,0.177 10 false 2 5.094,6.396 5.76,6.583 0.667,0.188 10 false IG1 NO. 3 4.75,6.906 4.99,7.094 0.24,0.188 10 false 10 3.917,7.135 4.615,7.313 0.698,0.177 10 false IG2-MAIN 4.802,7.302 4.969,7.479 0.167,0.177 10 false 7 5.063,7.646 5.729,7.833 0.667,0.188 10 false IG2 NO. 1 4.75,7.99 5.448,8.167 0.698,0.177 10 false 1A 5.917,7.292 6.156,7.479 0.24,0.188 10 false 8 5.917,6.906 6.156,7.094 0.24,0.188 10 false 9 5.906,6.052 6.146,6.24 0.24,0.188 10 false 1 5.917,5.594 6.156,5.781 0.24,0.188 10 false 3 6.094,7.135 7.125,7.333 1.031,0.198 10 false ECU-IG2 NO. 1 3.958,0.146 4.125,0.313 0.167,0.167 10 false 1 4.771,8.156 6.313,8.438 1.542,0.281 10 false No. 1 Integration Relay 2.094,7.75 3.625,8.177 1.531,0.427 10 false Certification ECU (Smart Key ECU Assembly)

B424461E13
4.99,0.854 5.448,1.052 0.458,0.198 10 false F1 4.979,2.01 5.438,2.208 0.458,0.198 10 false F1 4.938,3.552 5.396,3.75 0.458,0.198 10 false M67 4.948,4.698 5.406,4.896 0.458,0.198 10 false M67 4.938,6.208 5.396,6.406 0.458,0.198 10 false M67 4.938,7.365 5.396,7.563 0.458,0.198 10 false M67 4.99,7.156 5.448,7.354 0.458,0.198 10 false 10 4.99,6 5.448,6.198 0.458,0.198 10 false 11 5.031,4.51 5.49,4.708 0.458,0.198 10 false 6 5.031,3.365 5.49,3.563 0.458,0.198 10 false 5 5.021,0.667 5.479,0.865 0.458,0.198 10 false 8 5.021,1.802 5.479,2 0.458,0.198 10 false 9 5.302,0.76 5.76,0.958 0.458,0.198 10 false CLG5 5.302,1.906 5.76,2.104 0.458,0.198 10 false CG5B 5.313,3.438 5.771,3.635 0.458,0.198 10 false CLG6 5.302,4.604 5.76,4.802 0.458,0.198 10 false CG6B 5.313,6.094 5.771,6.292 0.458,0.198 10 false CLG7 5.302,7.26 5.76,7.458 0.458,0.198 10 false CG7B 5.844,6.781 6.302,6.979 0.458,0.198 10 false IC 5.844,4.125 6.302,4.323 0.458,0.198 10 false IC 5.833,1.396 6.292,1.594 0.458,0.198 10 false IC 5.104,7.958 6.646,8.385 1.542,0.427 10 false Certification ECU (Smart Key ECU Assembly) 0.385,7.719 0.844,7.917 0.458,0.198 10 false M37 0.24,5.031 0.698,5.229 0.458,0.198 10 false M10 0.229,2.292 0.688,2.49 0.458,0.198 10 false F58 1.208,0.75 1.833,0.948 0.625,0.198 10 false ANTE5 1.271,1.906 1.729,2.104 0.458,0.198 10 false CLGB 1.75,7.26 2.25,7.542 0.5,0.281 10 false 3 1.74,6.094 2.24,6.375 0.5,0.281 10 false 1 1.729,3.458 2.229,3.74 0.5,0.281 10 false 1 1.74,0.75 2.24,1.031 0.5,0.281 10 false 1 1.74,4.604 2.24,4.885 0.5,0.281 10 false 3 1.74,1.906 2.24,2.188 0.5,0.281 10 false 3 1.198,3.458 1.76,3.688 0.563,0.229 10 false ANTE6 1.198,6.094 1.771,6.292 0.573,0.198 10 false ANTE7 1.271,4.615 1.729,4.813 0.458,0.198 10 false CLGB 1.281,7.26 1.74,7.458 0.458,0.198 10 false CLGB 0.229,2.458 2.448,2.948 2.219,0.49 10 false No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) 0.24,5.198 2.479,5.635 2.24,0.438 10 false No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor) 0.385,7.875 2.094,8.427 1.708,0.552 10 false No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION

·

After completing repairs, confirm that the problem does not recur.



HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Press a switch of the electrical key transmitter sub-assembly.

OK:

The electrical key transmitter sub-assembly LED illuminates.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (KEY LOW BATTERY)

NG

28.INSPECT TRANSMITTER BATTERY
2.READ VALUE USING GTS (KEY LOW BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Low Battery Transmitter battery depleted No or Yes No: Transmitter battery not depleted
Yes: Transmitter battery depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
Body Electrical > Entry&Start > Data List
Tester Display
Key Low Battery
50003 125 23
OK:

"No" is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

3.CHECK POWER SWITCH CONDITION

NG

REPLACE TRANSMITTER BATTERY

3.CHECK POWER SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the power switch causes the power source mode to change.


Result:
Result Proceed to
The power source mode does not change A
The power source mode changes B



A

4.CHECK ENTRY AND START SYSTEM (for Start Function)

B

AFFECTED BY WAVE INTERFERENCE

4.CHECK ENTRY AND START SYSTEM (for Start Function)
a.

Remove the transmitter battery from the electrical key transmitter sub-assembly.


b.
E362385C02
0.5,0.438 0.927,0.688 false 2.49,0.792 2.917,1.042 false 0.271,0.313 0.583,0.51 0.313,0.198 10 false *1 3,1.01 3.313,1.208 0.313,0.198 10 false *2
*1 Power Switch
*2 Electrical Key Transmitter Sub-assembly


With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch and check if the power source mode changes.

HINT:

If the power source mode changes, the cabin verification is malfunctioning.


OK:

The power source mode changes.



Result:
Result Proceed to
The power source mode changes A
The power source mode does not change B



A

5.CHECK WAVE ENVIRONMENT

B

21.CHECK KEY DIAGNOSTIC MODE
5.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER>INSTALLATION


b.

Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform an entry and start system check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>OPERATION CHECK

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).



c.

Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (rear floor) and perform an entry and start system check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>OPERATION CHECK

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).


HINT:

Check that the customize setting "Ignition Available Area" is set to "All".



d.

Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key antenna assembly (inside luggage compartment) and perform an entry and start system check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>OPERATION CHECK

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 3 indoor electrical key antenna assembly (inside luggage compartment).


HINT:

Check that the customize setting "Ignition Available Area" is set to "All".



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

The hybrid control system starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the power switch is pressed with the brake pedal depressed.


Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

6.CHECK FOR DTC (ENTRY&START)
6.CHECK FOR DTC (ENTRY&START)
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

7.CHECK FOR DTC (POWER SOURCE CONTROL)

NG

7.CHECK FOR DTC (POWER SOURCE CONTROL)
a.

Check for DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

8.CHECK KEY DIAGNOSTIC MODE

NG

8.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which indoor electrical key antenna assembly (front floor, rear floor or inside luggage compartment) is operating by the sounding of the buzzer.

·

When the wireless buzzer sounds for all indoor electrical key antenna assemblies, they can be judged as operating properly and a malfunction in the certification ECU (smart key ECU assembly), which performs verification, is suspected.

·

When the wireless buzzer does not sound for all indoor electrical key antenna assemblies, it can be judged that the certification ECU (smart key ECU assembly), which controls the indoor electrical key antenna assemblies, is malfunctioning.




b.
E351995C05
0.573,0.708 2.656,0.281 2.656,0.281 1.938,0.698 true 2.719,0.177 3.031,0.333 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.


c.
E351996C05
0.573,0.552 2.531,0.188 2.531,0.188 1.906,0.563 true 2.594,0.094 2.906,0.25 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.


d.
E351998C05
1.24,1.75 2.479,0.313 2.479,0.313 1.854,1.219 true 2.531,0.219 2.844,0.375 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 3 indoor electrical key antenna assembly (inside luggage compartment).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.


Result:
Result Proceed to
The wireless buzzer does not sound for all indoor electrical key antenna assemblies A
The wireless buzzer does not sound for only the No. 1 indoor electrical key antenna assembly (front floor) B
The wireless buzzer does not sound for only the No. 2 indoor electrical key antenna assembly (rear floor) C
The wireless buzzer does not sound for only the No. 3 indoor electrical key antenna assembly (inside luggage compartment) D
The wireless buzzer sounds for all indoor electrical key antenna assemblies E



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

C

12.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

D

15.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))

E

18.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.

Using an oscilloscope, check the waveform.

B431370C35
1.625,0.49 2.01,0.729 0.385,0.24 1.417,2.083 1.604,1.615 true 2.25,2.083 2.031,1.615 true 0.448,0.271 0.76,0.427 0.313,0.156 10 false *a 3.604,0.271 3.917,0.427 0.313,0.156 10 false *b 4.75,1.969 5.063,2.125 0.313,0.156 10 false *c 5.552,1.979 5.865,2.135 0.313,0.156 10 false *d 1.708,0.521 2.042,0.729 0.333,0.208 10 false F58 2.104,2.125 2.833,2.406 0.729,0.281 10 false CLGB 3.99,1.292 4.302,1.448 0.313,0.156 10 false GND 1.219,2.125 1.958,2.406 0.74,0.281 10 false ANTE5
*a Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Front Floor))
*b Waveform 1
*c For 30 seconds after closing any door *d After 30 seconds or more have elapsed since any door closed


OK:
Tester Connection Condition Tool Setting Specified Condition
F58-1 (ANTE5) - F58-3 (CLGB) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

10.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)
a.

Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR (for Front Floor)>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK POWER SOURCE MODE
11.CHECK POWER SOURCE MODE
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Press the power switch with the brake pedal released and check that the power source mode changes.


Result:
Result Proceed to
The power source mode changes A
The power source mode does not change B



A

END (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR) WAS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Using an oscilloscope, check the waveform.

B431370C38
1.625,0.49 2.01,0.729 0.385,0.24 1.417,2.083 1.604,1.615 true 2.25,2.083 2.031,1.615 true 0.448,0.271 0.76,0.427 0.313,0.156 10 false *a 3.604,0.271 3.917,0.427 0.313,0.156 10 false *b 4.75,1.969 5.063,2.125 0.313,0.156 10 false *c 5.552,1.979 5.865,2.135 0.313,0.156 10 false *d 1.708,0.521 2.042,0.729 0.333,0.208 10 false M10 2.104,2.125 2.833,2.406 0.729,0.281 10 false CLGB 3.99,1.292 4.302,1.448 0.313,0.156 10 false GND 1.177,2.125 1.917,2.406 0.74,0.281 10 false ANTE6
*a Front view of wire harness connector
(to No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor))
*b Waveform 1
*c For 30 seconds after closing any door *d After 30 seconds or more have elapsed since any door closed


OK:
Tester Connection Condition Tool Setting Specified Condition
M10-1 (ANTE6) - M10-3 (CLGB) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

13.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

13.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)
a.

Temporarily replace the No. 2 indoor electrical key antenna assembly (rear floor) with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Rear Floor)>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK POWER SOURCE MODE
14.CHECK POWER SOURCE MODE
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Press the power switch with the brake pedal released and check that the power source mode changes.


Result:
Result Proceed to
The power source mode changes A
The power source mode does not change B



A

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR) WAS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

15.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT))
a.

Using an oscilloscope, check the waveform.

B431370C37
1.625,0.49 2.01,0.729 0.385,0.24 1.417,2.083 1.604,1.615 true 2.25,2.083 2.031,1.615 true 0.448,0.271 0.76,0.427 0.313,0.156 10 false *a 3.604,0.271 3.917,0.427 0.313,0.156 10 false *b 4.75,1.969 5.063,2.125 0.313,0.156 10 false *c 5.552,1.979 5.865,2.135 0.313,0.156 10 false *d 1.698,0.521 2.021,0.74 0.323,0.219 10 false M37 2.104,2.125 2.833,2.406 0.729,0.281 10 false CLGB 3.99,1.292 4.302,1.448 0.313,0.156 10 false GND 1.219,2.125 1.958,2.406 0.74,0.281 10 false ANTE7
*a Front view of wire harness connector
(to No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage Compartment))
*b Waveform 1
*c For 30 seconds after closing any door *d After 30 seconds or more have elapsed since any door closed


OK:
Tester Connection Condition Tool Setting Specified Condition
M37-1 (ANTE7) - M37-3 (CLGB) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

16.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

16.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT)
a.

Temporarily replace the No. 3 indoor electrical key antenna assembly (inside luggage compartment) with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR (for Luggage Compartment)>REMOVAL


Result:
Proceed to
NEXT



NEXT

17.CHECK POWER SOURCE MODE
17.CHECK POWER SOURCE MODE
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Press the power switch with the brake pedal released and check that the power source mode changes.


Result:
Result Proceed to
The power source mode changes A
The power source mode does not change B



A

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE COMPARTMENT) WAS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

18.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Power switch 1 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

If the power switch is pressed for a short time, the display may not change.

·

Use this item to determine if the power switch input signal is malfunctioning.


Start Switch2 Power switch 2 status OFF or ON OFF: Power switch not pressed
ON: Power switch pressed
·

Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.

·

Behaves the same way as power switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

NG

19.INSPECT POWER SWITCH
19.INSPECT POWER SWITCH


Result:
Result Proceed to
OK A
NG (for LHD with 2ZR-FXE) B
NG (for RHD with 2ZR-FXE) C
NG (for LHD with M20A-FXS) D
NG (for RHD with M20A-FXS) E



A

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)

B

C

D

E

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER SWITCH)
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F59 power switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-23 (SSW1) - F59-5 (SS1) Always Below 1 Ω
F1-21 (SSW2) - F59-1 (SS2) Always Below 1 Ω
F1-11 (AGND) - F59-6 (AGND) Always Below 1 Ω
F1-23 (SSW1) or F59-5 (SS1) - Body ground Always 10 kΩ or higher
F1-21 (SSW2) or F59-1 (SS2) - Body ground Always 10 kΩ or higher
F1-11 (AGND) or F59-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check if the transponder key amplifier built into the power switch is operating by the sounding of the buzzer.




b.
E362385C03
0.5,0.438 0.927,0.688 false 2.49,0.792 2.917,1.042 false 0.271,0.313 0.583,0.51 0.313,0.198 10 false *1 3,1.01 3.313,1.208 0.313,0.198 10 false *2
*1 Power Switch
*2 Electrical Key Transmitter Sub-assembly


Check the power switch.

Face the logo side of the electrical key transmitter sub-assembly toward the power switch, hold the electrical key transmitter sub-assembly near the power switch and check that the wireless buzzer sounds.


Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds (for LHD) B
The wireless buzzer sounds (for RHD) C



A

22.CHECK FOR DTC

B

C

22.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output A
Entry and start system (for Start Function) DTCs are output B



A

23.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

B

23.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

24.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

24.CHECK HARNESS AND CONNECTOR (GROUND)

OK

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 3A and 3D instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-16 (ACCD) - 3A-30 Always Below 1 Ω
F1-17 (IG1D) - 3A-17 Always Below 1 Ω
3D-3 - Body ground Always Below 1 Ω
F1-16 (ACCD) or 3A-30 - Body ground Always 10 kΩ or higher
F1-17 (IG1D) or 3A-17 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1-NO. 1, IG1-NO. 2, IG2-NO. 2, ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1-NO. 1, IG1-NO. 2, IG2-NO. 2, ACC RELAY)

b.

Measure the resistance according to the value(s) in the table below.

E352017C01
1.344,0.563 1.75,0.792 0.406,0.229 3.75,0.563 4.156,0.792 0.406,0.229 5.271,0.573 5.677,0.802 0.406,0.229 6.281,0.563 6.688,0.792 0.406,0.229 1.573,2.156 1.979,2.385 0.406,0.229 4.781,2.156 5.188,2.385 0.406,0.229 3.875,0.604 4.188,0.802 0.313,0.198 10 false 3F 1.438,0.594 1.75,0.792 0.313,0.198 10 false 3H 5.396,0.604 5.708,0.802 0.313,0.198 10 false 3L 6.406,0.604 6.719,0.802 0.313,0.198 10 false 3K 1.677,2.188 1.99,2.385 0.313,0.198 10 false 3D 4.885,2.188 5.198,2.385 0.313,0.198 10 false 3A 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3A-30 - 3D-3 20°C (68°F) 285.71 to 428.57 Ω
3A-17 - 3D-3 20°C (68°F) 85.69 to 124.1 Ω
3K-1 - 3A-40 Auxiliary battery voltage applied between terminals 3A-30 and 3D-3 Below 1 Ω
Auxiliary battery voltage not applied between terminals 3A-30 and 3D-3 10 kΩ or higher
3K-1 - 3F-10 Auxiliary battery voltage applied between terminals 3A-17 and 3D-3 Below 1 Ω
Auxiliary battery voltage not applied between terminals 3A-17 and 3D-3 10 kΩ or higher
3K-1 - 3H-12 Auxiliary battery voltage applied between terminals 3A-17 and 3D-3 Below 1 Ω
Auxiliary battery voltage not applied between terminals 3A-17 and 3D-3 10 kΩ or higher
3L-1 - 3D-19 Auxiliary battery voltage applied between terminals 3A-17 and 3D-3 Below 1 Ω
Auxiliary battery voltage not applied between terminals 3A-17 and 3D-3 10 kΩ or higher



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

27.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

27.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

b.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


c.

Measure the voltage while confirming the power source mode on the Data List.

B427583C33
4.458,0.354 4.896,0.615 0.438,0.26 3.958,2.073 4.25,1.219 true 4.552,2.073 4.344,1.219 true 4.438,2.125 5.052,2.323 0.615,0.198 10 false ACCD 3.813,2.125 4.427,2.323 0.615,0.198 10 false IG1D 4.594,0.406 5.208,0.604 0.615,0.198 10 false F1 0.177,0.094 0.49,0.25 0.313,0.156 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Power switch off
ACC ON: Power switch on (ACC)
IG ON: Power switch on (IG)
ST ON: Sending hybrid control system start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18
Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-17 (IG1D) - Body ground Power switch off 1 V or less
Power switch on (ACC) 1 V or less
Power switch on (IG) 9 V or higher
F1-16 (ACCD) - Body ground Power switch off 1 V or less
Power switch on (ACC) 8.5 V or higher
Power switch on (IG) 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

28.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER>INSPECTION

NOTICE:

Do not wrap the lead wire ground a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY