Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP(for RHD) › 2019.09–2020.08
RM32K0E _54 Brake _060045 BRAKE SYSTEM (OTHER) _0299586 BRAKE BOOSTER PUMP(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light/yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:(Click here)
for Calibration:(Click here)

NOTICE:

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


PROCEDURE

Hide 1.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

Hide 86510A 2.REMOVE SECURITY HORN ASSEMBLY (w/ Security Horn)

Hide 3.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (for M20A-FXS)

Hide 4.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (for 2ZR-FXE)

Hide 5.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 44571A 6.SEPARATE NO. 1 BRAKE ACTUATOR HOSE

a.
C366960

Slide the clip and separate the No. 1 brake actuator hose from the No. 1 brake actuator tube.


Hide 473A1 7.SEPARATE ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C366961

Using a union nut wrench, disconnect the accumulator to brake master cylinder tube from the brake booster pump assembly.


b.
C366962

Remove the bolt to separate the accumulator to brake master cylinder tube.


Hide 8.REMOVE BRAKE ACTUATOR WITH BRAKE BOOSTER PUMP ASSEMBLY

a.
C343268C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake booster pump assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C366963C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



c.

Disengage the clamp to separate the engine room main wire.


d.
C366964C01
1.333,1.552 1.531,1.302 true 2.385,1.51 2.073,1.073 true 2.219,0.698 1.906,0.802 true 2.01,0.448 1.729,0.854 true 0.958,0.469 1.479,0.927 true 0.969,0.875 1.281,1.021 true 1.188,1.604 1.427,1.813 0.24,0.208 10 true *a 2.396,1.552 2.635,1.75 0.24,0.198 10 true *b 2.24,0.604 2.5,0.813 0.26,0.208 10 true *c 2.052,0.302 2.271,0.5 0.219,0.198 10 true *d 0.74,0.344 0.927,0.542 0.188,0.198 10 true *e 0.698,0.76 0.927,0.99 0.229,0.229 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Use tags or make a memo to identify the places to reconnect the brake lines.


e.
C343270

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.


f.
C366965

Disengage the 2 clamps to separate the 2 brake lines from the No. 4 brake tube clamp.


g.

Disengage the clamp to remove the No. 4 brake tube clamp from the brake actuator bracket assembly.


h.
C366966

Remove the 2 bolts, 2 nuts and brake actuator with brake booster pump assembly from the vehicle body.

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake booster pump assembly by the connector, union or wire harness.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with brake booster pump assembly when carrying it.



HINT:

Remove the brake actuator with brake booster pump assembly while avoiding the brake lines.



Hide 44571A 9.REMOVE NO. 1 BRAKE ACTUATOR HOSE

a.
C343276

Slide the clip and remove the No. 1 brake actuator hose from the brake booster pump assembly.


b.
C343278

Remove the No. 1 brake actuator hose from the brake actuator hose clamp.


Hide 47381 10.REMOVE NO. 1 BRAKE TUBE CLAMP BRACKET

a.
C343275

Remove the bolt and No. 1 brake tube clamp bracket from the brake booster pump assembly.


Hide 47070 11.REMOVE BRAKE BOOSTER PUMP ASSEMBLY

a.
C343280

Disengage the claw and 4 clamps to separate the brake booster pump assembly wire harness from the brake actuator assembly bracket.


b.
C343281

Remove the nut from the brake booster pump assembly.


c.
C343282C02
2.927,2.813 2.635,2.813 false 2.49,4.073 2.198,4.073 false 1.042,4.26 1.042,4.469 1.042,4.469 0.854,4.469 false 1.104,3.938 1.104,3.75 1.104,3.75 0.917,3.75 false 2.521,4 2.833,4.156 0.313,0.156 10 false *1 2.969,2.75 3.281,2.906 0.313,0.156 10 false *2 0.75,3.688 1.063,3.844 0.313,0.156 10 false *3 0.698,4.406 1.01,4.563 0.313,0.156 10 false *4
*1 Union
*2 Connector
*3 Wire Harness
*4 Stud


Remove the brake booster pump assembly, brake booster pump bushing and brake actuator case collar from the brake actuator bracket assembly.

NOTICE:
·

Do not carry the brake booster pump assembly by the parts shown in the illustration.

·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.