Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1860  Short in Knee Airbag (D Side) Squib Circuit  B1861  Open in Knee Airbag (D Side) Squib Circuit  B1862  Short in Knee Airbag (D Side) Squib Circuit (to Ground)  B1863  Short in Knee Airbag (D Side) Squib Circuit (to +B)  


DESCRIPTION

The driver side knee airbag squib circuit consists of the airbag sensor assembly and lower No. 1 instrument panel airbag assembly.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side knee airbag squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1860 Short in Knee Airbag (D Side) Squib Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the driver side knee airbag squib during the primary check.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Driver side knee airbag squib (Lower No. 1 instrument panel airbag assembly)

·

Airbag sensor assembly


Applies to check mode
B1861 Open in Knee Airbag (D Side) Squib Circuit Any of the following conditions is met:
·

The airbag sensor assembly detects an open in the driver side knee airbag squib.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Driver side knee airbag squib (Lower No. 1 instrument panel airbag assembly)

·

Airbag sensor assembly


Applies to check mode
B1862 Short in Knee Airbag (D Side) Squib Circuit (to Ground) Any of the following conditions is met:
·

The airbag sensor assembly detects a short to ground in the driver side knee airbag squib.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Driver side knee airbag squib (Lower No. 1 instrument panel airbag assembly)

·

Airbag sensor assembly


Applies to check mode
B1863 Short in Knee Airbag (D Side) Squib Circuit (to +B) Any of the following conditions is met:
·

The airbag sensor assembly detects a short to B+ in the driver side knee airbag squib.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Driver side knee airbag squib (Lower No. 1 instrument panel airbag assembly)

·

Airbag sensor assembly


Applies to check mode

DTC Detection Conditions (B1860):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the driver side knee airbag squib during the primary check ○ - -
Driver side knee airbag squib malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1861):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects an open in the driver side knee airbag squib ○ - -
Driver side knee airbag squib malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1862):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects a short to ground in the driver side knee airbag squib ○ - -
Driver side knee airbag squib malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

DTC Detection Conditions (B1863):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status The airbag sensor assembly detects a short to B+ in the driver side knee airbag squib ○ - -
Driver side knee airbag squib malfunction - ○ -
Airbag sensor assembly malfunction - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C386403E15
4.917,2.948 5.656,3.167 0.74,0.219 10 false F150 4.917,3.125 6.917,3.542 2,0.417 10 false Airbag Sensor Assembly 0.396,2.448 1.146,2.667 0.75,0.219 10 false F31 0.385,2.615 3.052,3.458 2.667,0.844 10 false Driver Side Knee Airbag Squib (Lower No. 1 Instrument Panel Airbag Assembly) 4.979,1.323 5.5,1.667 0.521,0.344 10 false DK+ 4.698,1.323 4.917,1.698 0.219,0.375 10 false 13 4.979,1.885 5.5,2.25 0.521,0.365 10 false DK- 4.698,1.885 4.906,2.26 0.208,0.375 10 false 12 2.083,1.333 2.25,1.75 0.167,0.417 10 false 1 2.094,1.885 2.333,2.25 0.24,0.365 10 false 2 1.677,1.323 2.083,1.667 0.406,0.344 10 false DK+ 1.698,1.885 2,2.25 0.302,0.365 10 false DK-

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C239229C01
0.552,1.115 0.552,1.542 false 1.313,0.979 1.313,0.604 1.313,0.604 1.146,0.604 false 0.469,1.573 0.958,1.958 0.49,0.385 10 *1 0.979,0.531 1.313,0.854 0.333,0.323 10 *3 2.313,0.969 2.625,1.344 0.313,0.375 10 *2 1.865,0.969 2.188,1.427 0.323,0.458 10 A 1.5,0.969 1.802,1.406 0.302,0.438 10 B 1.021,0.969 1.396,1.417 0.375,0.448 10 C 0.656,0.969 1.146,1.531 0.49,0.563 10 D
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the instrument panel wire connector (on the lower No. 1 instrument panel airbag assembly side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanism of the instrument panel wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

2.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
a.
C247056C14
0.448,2.24 0.833,2.479 0.385,0.24 0.667,0.906 0.667,1.302 false 1.844,2.26 2.021,2.26 false 0.594,1.313 0.938,1.656 0.344,0.344 10 false *1 2.25,0.75 2.573,1.115 0.323,0.365 10 false *2 1.813,0.76 2.083,1.094 0.271,0.333 10 false A 1.656,0.76 1.979,1.198 0.323,0.438 10 false B 1.146,0.76 1.385,1.156 0.24,0.396 10 false C 0.781,0.76 1.063,1.188 0.281,0.427 10 false D 0.531,2.281 0.813,2.51 0.281,0.229 10 false F31 2.063,2.177 2.542,2.552 0.479,0.375 10 false SST 0.313,1.698 0.625,2.146 0.313,0.448 10 false *a
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly)


Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the lower No. 1 instrument panel airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1860, B1861, B1862 or B1863 is not output.


HINT:

Codes other than DTCs B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

REPLACE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

NG

3.CHECK INSTRUMENT PANEL WIRE
3.CHECK INSTRUMENT PANEL WIRE
a.
C245639C18
0.51,2.219 0.875,2.458 0.365,0.24 1.469,2.323 1.073,2.563 true 1.698,2.323 2.042,2.563 true 0.51,0.875 0.51,0.458 0.51,0.458 0.375,0.458 false 1.354,0.875 1.354,0.458 1.354,0.458 1.219,0.458 false 0.635,0.865 1.135,1.208 0.5,0.344 10 false D 1.031,0.865 1.354,1.177 0.323,0.313 10 false C 1.594,0.875 1.927,1.167 0.333,0.292 10 false B 1.99,0.875 2.563,1.271 0.573,0.396 10 false A 2.406,0.875 2.74,1.135 0.333,0.26 10 false *2 0.938,2.573 1.396,2.875 0.458,0.302 10 false DK+ 0.583,2.26 0.844,2.458 0.26,0.198 10 false F31 2,2.573 2.635,2.885 0.635,0.313 10 false DK- 0.302,1.875 0.604,2.177 0.302,0.302 10 false *a 0.219,0.385 0.688,0.698 0.469,0.313 10 false *1 1.073,0.385 1.552,0.708 0.479,0.323 10 false *3
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly)


Disconnect the instrument panel wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F31-1 (DK+) - Body ground Power switch on (IG) Below 1 V
F31-2 (DK-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-1 (DK+) - F31-2 (DK-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-1 (DK+) - Body ground Always 1 MΩ or higher
F31-2 (DK-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-1 (DK+) - F31-2 (DK-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK DTC
a.
C238245C01
0.844,1.146 0.844,1.458 false 0.969,1 1.219,1.385 0.25,0.385 10 false D 1.125,1 1.333,1.417 0.208,0.417 10 false C 1.583,1 1.823,1.354 0.24,0.354 10 false B 1.74,1 2,1.323 0.26,0.323 10 false A 2.167,0.99 2.458,1.313 0.292,0.323 10 false *2 0.76,1.479 1.083,1.781 0.323,0.302 10 false *1
*1 Lower No. 1 Instrument Panel Airbag Assembly
*2 Airbag Sensor Assembly


Connect the connectors to the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1860, B1861, B1862 or B1863 is not output.


HINT:

Codes other than DTCs B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG