Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0410446 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1688  Camera Supply Voltage Malfunction (Back or Front or RH Side or LH Side)  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a problem with the current supplied from the rear television camera assembly, front television camera assembly, side television camera assembly RH and side television camera assembly LH to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1688 Camera Supply Voltage Malfunction (Back or Front or RH Side or LH Side) Camera current malfunction
·

Harness or connector

·

Parking assist ECU

·

Rear television camera assembly

·

Front television camera assembly

·

Side television camera assembly RH

·

Outer rear view mirror assembly with cover RH

·

Side television camera assembly LH

·

Outer rear view mirror assembly with cover LH



WIRING DIAGRAM

E403268E07
0.385,1.708 2.76,1.948 2.375,0.24 10 false Rear Television Camera Assembly 1.688,1.198 2.135,1.354 0.448,0.156 10 false CGND 1.781,0.729 2.083,0.906 0.302,0.177 10 false CB+ 2.156,0.615 2.365,0.781 0.208,0.167 10 false 6 0.385,1.531 0.865,1.698 0.479,0.167 10 false S11 2.156,1.083 2.365,1.25 0.208,0.167 10 false 5 5.073,0.604 5.281,0.771 0.208,0.167 10 false 8 5.26,0.719 5.563,0.896 0.302,0.177 10 false CB+ 4.99,1.083 5.198,1.25 0.208,0.167 10 false 25 5.24,1.177 5.667,1.354 0.427,0.177 10 false CGND 0.365,3.698 2.698,3.927 2.333,0.229 10 false Front Television Camera Assembly 0.375,3.542 0.885,3.771 0.51,0.229 10 false B17 1.656,2.76 2.083,2.938 0.427,0.177 10 false BCB+ 1.656,3.24 2.083,3.417 0.427,0.177 10 false BGND 2.146,2.667 2.354,2.833 0.208,0.167 10 false 6 2.156,3.135 2.365,3.302 0.208,0.167 10 false 5 5.073,2.656 5.281,2.823 0.208,0.167 10 false 7 5.25,2.781 5.677,2.958 0.427,0.177 10 false BCB+ 5.281,3.24 5.708,3.417 0.427,0.177 10 false BGND 5,3.125 5.208,3.292 0.208,0.167 10 false 24 0.094,5.302 1.552,5.708 1.458,0.406 10 false Side Television Camera Assembly RH 1.615,5.292 2.323,5.469 0.708,0.177 10 false I7 1.604,5.458 4.677,5.677 3.073,0.219 10 false Outer Rear View Mirror Assembly with Cover RH 2.094,4.375 2.521,4.552 0.427,0.177 10 false RCB+ 2.083,4.854 2.51,5.031 0.427,0.177 10 false RGND 2.563,4.26 3.229,4.438 0.667,0.177 10 false 5 2.552,4.75 3.219,4.927 0.667,0.177 10 false 14 5.25,4.396 5.677,4.573 0.427,0.177 10 false RCB+ 5.063,4.25 5.271,4.417 0.208,0.167 10 false 6 5.25,4.854 5.677,5.031 0.427,0.177 10 false RGND 5.01,4.75 5.219,4.917 0.208,0.167 10 false 23 1.625,7.073 2.365,7.25 0.74,0.177 10 false J11 5.25,6.177 5.677,6.354 0.427,0.177 10 false LCB+ 5.063,6.042 5.271,6.208 0.208,0.167 10 false 9 5.25,6.625 5.677,6.802 0.427,0.177 10 false LGND 5,6.521 5.208,6.688 0.208,0.167 10 false 26 5.448,7.354 5.917,7.521 0.469,0.167 10 false M116 5.458,7.51 6.854,7.844 1.396,0.333 10 false Parking Assist ECU 2.563,6.052 3.229,6.229 0.667,0.177 10 false 5 2.542,6.521 3.208,6.698 0.667,0.177 10 false 14 2.115,6.156 2.542,6.333 0.427,0.177 10 false LCB+ 2.073,6.635 2.5,6.813 0.427,0.177 10 false LGND 0.115,7.115 1.573,7.521 1.458,0.406 10 false Side Television Camera Assembly LH 1.625,7.24 4.698,7.458 3.073,0.219 10 false Outer Rear View Mirror Assembly with Cover LH

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1688 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - PARKING ASSIST ECU)
2.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the S11 rear television camera assembly connector.


b.

Disconnect the M116 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S11-6 (CB+) - M116-8 (CB+) Always Below 1 Ω
S11-5 (CGND) - M116-25 (CGND) Always Below 1 Ω
S11-6 (CB+) or M116-8 (CB+) - Body ground Always 10 kΩ or higher
S11-5 (CGND) or M116-25 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the M116 parking assist ECU connector.


b.

Disconnect the B17 front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-7 (BCB+) - B17-6 (BCB+) Always Below 1 Ω
M116-24 (BGND) - B17-5 (BGND) Always Below 1 Ω
M116-7 (BCB+) or B17-6 (BCB+) - Body ground Always 10 kΩ or higher
M116-24 (BGND) or B17-5 (BGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH)
a.

Disconnect the M116 parking assist ECU connector.


b.

Disconnect the I7 outer rear view mirror assembly with cover RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-6 (RCB+) - I7-5 (RCB+) Always Below 1 Ω
M116-23 (RGND) - I7-14 (RGND) Always Below 1 Ω
M116-6 (RCB+) or I7-5 (RCB+) - Body ground Always 10 kΩ or higher
M116-23 (RGND) or I7-14 (RGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH)
a.

Disconnect the M116 parking assist ECU connector.


b.

Disconnect the J11 outer rear view mirror assembly with cover LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-9 (LCB+) - J11-5 (LCB+) Always Below 1 Ω
M116-26 (LGND) - J11-14 (LGND) Always Below 1 Ω
M116-9 (LCB+) or J11-5 (LCB+) - Body ground Always 10 kΩ or higher
M116-26 (LGND) or J11-14 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK PARKING ASSIST ECU
a.
E348000C57
1.51,0.365 1.917,0.604 0.406,0.24 2.083,1.271 1.031,0.417 true 2.156,1.281 1.646,1.521 true 2.25,1.302 1.406,1.948 true 2.344,1.313 2.552,2 true 2.552,0.625 2.385,1.125 true 2.458,0.417 2.302,1.125 true 2.375,0.26 2.219,1.125 true 1.938,0.198 2.135,1.104 true 1.542,0.396 1.927,0.552 0.385,0.156 10 false M116 0.115,0.063 0.313,0.24 0.198,0.177 10 false *a 2.354,0.073 2.667,0.229 0.313,0.156 10 false CB+ 2.51,0.281 2.927,0.438 0.417,0.156 10 false BCB+ 2.594,0.5 3.01,0.656 0.417,0.156 10 false RCB+ 1.594,0.031 2.01,0.188 0.417,0.156 10 false LCB+ 2.594,1.927 3.01,2.083 0.417,0.156 10 false RGND 1.104,1.958 1.521,2.115 0.417,0.156 10 false BGND 1.375,1.51 1.792,1.667 0.417,0.156 10 false CGND 0.625,0.313 1.042,0.469 0.417,0.156 10 false LGND
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-25 (CGND) - Body ground Always Below 1 Ω
M116-24 (BGND) - Body ground Always Below 1 Ω
M116-23 (RGND) - Body ground Always Below 1 Ω
M116-26 (LGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M116-8 (CB+) - M116-25 (CGND) Power switch on (IG) 5.5 to 7.05 V
M116-7 (BCB+) - M116-24 (BGND) Power switch on (IG) 5.5 to 7.05 V
M116-6 (RCB+) - M116-23 (RGND) Power switch on (IG) 5.5 to 7.05 V
M116-12 (LCB+) - M116-26 (LGND) Power switch on (IG) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

7.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

7.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Disconnect the B17 front television camera assembly connector.


b.

Disconnect the I7 outer rear view mirror assembly with cover RH connector.


c.

Disconnect the J11 outer rear view mirror assembly with cover LH connector.


d.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

e.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353

Result:
Result Proceed to
The rear view screen is displayed and DTC C1688 is not output A
The rear view screen is not displayed and DTC C1688 is output B



A

8.CHECK FRONT TELEVISION CAMERA ASSEMBLY

B

8.CHECK FRONT TELEVISION CAMERA ASSEMBLY
a.

Disconnect the S11 rear television camera assembly connector.


b.

Disconnect the I7 outer rear view mirror assembly with cover RH connector.


c.

Disconnect the J11 outer rear view mirror assembly with cover LH connector.


d.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

e.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353

Result:
Result Proceed to
The front view screen is displayed and DTC C1688 is not output A
The front view screen is not displayed and DTC C1688 is output B



A

9.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

B

9.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Disconnect the B17 front television camera assembly connector.


b.

Disconnect the I7 outer rear view mirror assembly with cover RH connector.


c.

Disconnect the S11 rear television camera assembly connector.


d.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

e.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353

Result:
Result Proceed to
The side view screen is displayed and DTC C1688 is not output A
The side view screen is not displayed and DTC C1688 is output B



A

10.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH

B

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
10.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1688 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER RH

12.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1688 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH